Related Manuals for Zeeko IRP600 FL
Summary of Contents for Zeeko IRP600 FL
- Page 1 Transport & Installation Manual IRP600 FL Version 2, Rev c X-Y Linear Axis Dec 2024...
-
Page 2: Table Of Contents
Connecting the polishing fluid drain hose ..............14 Connecting the compressed air supply ................15 Electrical connection ...................... 15 Operation at startup ........................ 16 Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 3: Preface
Transport and Installation manual, the user documentation is comprised of the following: ◼ Operation manual. ◼ Software manuals. ◼ Maintenance manual. Zeeko LTD Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 4: Instructions For This Manual
NOTE: Identifies application instructions and other useful and important information. TIP: Specifies information that could be useful and save you unnecessary time and effort. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 5: Installation Requirement
Please observe your local COSHH and health & safety regulations before using any chemicals. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 6: Electromagnetic Influence
The overall height of the machine is 3000 mm. 2700 mm 2700 mm 750 mm Figure 1 - Machine dimensions Slurry 750 mm delivery system Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 7: Accessibility
If a supply transformer is required, the secondary voltage supply to the machine must match the machine voltage specification. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 8: Delivery
ATTENTION: Please observe all instructions for transport of the machine if you are responsible for unloading. Immediately notify the carrier or Railroad Company and Zeeko Ltd of any damages and other defects, e.g. missing items. Version 2 – Rev c - Copyright © Zeeko Limited 2024... -
Page 9: Transport
SIDE OF THE GRANITE BASE (SEVERE DAMAGE WILL BE CAUSED!) ◼ Remove the packaging materials from the machine (shrink wrap) – NOT THE PALLET. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... - Page 10 Risk of Tipping Over! Figure 4 - Pallet forklift zones ◼ Slowly lift the pallet and carefully move it to the installation site. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual...
-
Page 11: Lifting The Machine From The Floor Onto The Pallet
Lifting the machine from the pallet onto the floor. Lifting the machine from the floor onto the pallet ATTENTION: Do not use other pallets than those provided by Zeeko. Risk of Tipping Over! The machine MUST ONLY be lifted, NOT TRANSPORTED without the pallet. - Page 12 Move the forks of the lift truck or forklift as far as possible under the machine. Figure 5 See ( Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual...
-
Page 13: Installation
A Torx #8 tool with extension can then be passed above the chamber lamp to manually unlock the door interlocks. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 14: Connection
Connect the drainpipe to the pipe fitting (DN40) in the paneling and to the polishing fluid unit. See Figure 2 Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 15: Electrical Connection
Figure 7 - Electrical connection of the machine The standard mains voltage is: ◼ 400 v/50/60 *Hz: 3-PE ±5 %. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual... -
Page 16: Operation At Startup
Fill the polishing fluid (lubricant) supply unit and connect it to the machine. ◼ Connect the compressed air supply Connect the machine to the power supply. Version 2 – Rev c - Copyright © Zeeko Limited 2024 IRP600 FL X-Y Linear Axis- Transport & Installation Manual...
Need help?
Do you have a question about the IRP600 FL and is the answer not in the manual?
Questions and answers