Senix PDHX2-M2-EU Instruction Manual page 5

a. Never operate at higher speed than the
maximum speed rating of the drill bit. At
higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
b. Always start drilling at low speed and with
the bit tip in contact with the workpiece.
At higher speeds, the bit is likely to bend if
allowed to rotate freely without contacting
the workpiece, resulting in personal injury.
c. Apply pressure only in direct line with the
bit and do not apply excessive pressure.
Bits can bend and cause breakage or loss
of control, resulting in personal injury.
3. Dust/Chip Extraction
Dust from materials such as lead-containing
coatings, some wood types, minerals
and metal can be harmful to one's health.
Touching or breathing in the dust can cause
allergic reactions and/ or lead to respiratory
infections of the user or bystanders. Certain
dust, such as oak or beech dust, is considered
carcinogenic, especially in connection with
wood-treatment additives (chromate, wood
preservative). Materials containing asbestos
may only be worked on by specialists.
a. Ensure the workplace is properly ventilated
at all times.
b. Wearing a P2 filter-class respirator is rec-
ommended while working in a dusty envi-
ronment.
c. Observe the relevant regulations in your
country for the materials to be worked on.
d. Avoid dust accumulation at the workplace.
Dust can easily ignite.
ADDITIONAL SAFETY
INFORMATION FOR DRILL
a. Secure the workpiece. A workpiece
clamped with clamping devices or in a vice
is held more securely than by hand.
b. Always wait until the power tool has come
to a complete stop before placing it down.
The drill or driving bit can jam and cause
you to lose control of the power tool.
c. Switch the power tool off immediately if
the drill or driving bit becomes blocked. Be
prepared for high torque reactions which
cause kickback. The drill or driving bit be-
comes blocked when it becomes jammed
in the workpiece or when the power tool
becomes overloaded.
d. Use suitable detectors to determine if
there are hidden supply lines or contact the
SENIX.COM.AU
local utility company for assistance. Con-
tact with electric cables can cause fire and
electric shock. Damaging gas lines can lead
to explosion. Breaking water pipes causes
property damage.
e. Hold the power tool securely. When tight-
ening and loosening screws be prepared
for temporarily high torque reactions.
f. In case of damage or improper use of the
battery, vapors may be emitted. The battery
can be set aflame or explode. Ensure the
area is well ventilated and seek medical
attention should you experience any ad-
verse effects. The vapors may irritate the
respiratory system.
g. Do not open the battery. There is a risk of
short-circuiting.
h. The battery can be damaged by pointed
objects such as nails or screwdrivers or by
force applied externally. An internal short
circuit may occur, causing the battery to
burn, smoke, explode or overheat.
i. Only use the battery with products from the
manufacturer. This is the only way in which
you can protect the battery against dan-
gerous overload.
SAFETY WARNING FOR
BATTERY PACK AND
BATTERY CHARGER
• Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack may
create a risk of fire when used with another
battery pack.
• Use appliances only with specifically des-
ignated battery packs. Use of any other
battery packs may create a risk of injury
and fire.
WARNING!
Only use following batteries: B20X2/B25X2/
B40X2/B50X2/B60X2/B80X2 and chargers:
CHX2/CHQX2/CHQX2-M-EU/CHDX2-M-EU.
• When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or oth-
er small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
• Under abusive conditions, liquid may be
5 - EN