Download
Share
Print this page
Husqvarna 333R Mark II Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 333R Mark II
  6. Operator's manual
Husqvarna 333R Mark II Operator's Manual

Husqvarna 333R Mark II Operator's Manual

Hide thumbs Also See for 333R Mark II:

Advertisement

Quick Links

Download this manual
333R Mark II, 333RB Mark II
EN
Operator's manual
10-25

Advertisement

loading
Need help?

Need help?

Do you have a question about the 333R Mark II and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Husqvarna 333R Mark II

Summary of Contents for Husqvarna 333R Mark II

  • Page 1 333R Mark II, 333RB Mark II Operator's manual 10-25...
  • Page 2 333R Mark II 333RB Mark II...
  • Page 3 333R Mark II 333RB Mark II 333R Mark II 333RB Mark II...
  • Page 4 333R Mark II 333RB Mark II...
  • Page 5 1-2mm...

  • Page 10: Table Of Contents

    Contents Introduction..............10 Transportation and storage...........23 Safety................11 Technical data.............. 23 Assembly..............15 Accessories..............25 Operation..............17 EC Declaration of Conformity........25 Maintenance..............20 Appendix ..............26 Troubleshooting............22 Introduction Product description the product for other tasks than grass trimming and grass clearing. Use a grass blade or trimmer head to This product is a brushcutter with a combustion engine.

  • Page 11: Product Damage

    We are not responsible for damages to our product if: • the product is incorrectly repaired. (Fig. 12) Air purge bulb. (333R Mark II) • the product is repaired with parts that are not from the manufacturer or not approved by the (Fig.

  • Page 12: Safety Instructions For Operation

    can cause injury or death because of asphyxiation or will operate the product before you start to operate carbon monoxide. the product. • When you use this product the engine makes an • Do not turn with the product before you make sure electromagnetic field.
  • Page 13 • Make sure that you have a first aid kit near. (Fig. 21) Protective devices on the product Harness quick release (333R Mark II) • Make sure that you regularly do the maintenance to WARNING: the product. Do not use the harness if the harness quick release (A) is damaged.

  • Page 14: Trimmer Head

    To attach and remove the locknut completely and disconnect the spark plug cap before you start to work on it. WARNING: Stop the engine, use Cutting equipment protective gloves and be careful around the sharp edges of the cutting attachment. •...

  • Page 15: Fuel Safety

    3. Put on the harness and hang the product from the To install the main body (333R Mark II) support hook. 1. Connect the engine (A) to the tube (B) with four 4. Make a last adjustment to make sure the product screws (C).

  • Page 16: To Install The Transport Guard

    2. Put the loop handle on the shaft and put the lower 6. Put the support cup (F) on the output shaft with the clamp below the shaft. not flat side against the blade. 3. Align the lower clamp pin with the correct hole in the 7.

  • Page 17: To Adjust The Harness

    (333R Mark II) (Fig. 45) 6. When the hole (H) moves directly below the stopper b) (333RB Mark II) (Fig. 46) (I), you can hear a click which means the stopper 5.

  • Page 18: To Start And Stop

    • Shake the fuel container before you add the fuel • If Husqvarna two-stroke oil is not available, you can mixture to the fuel tank. use another two-stroke oil of good quality that is intended for air cooled engines. Contact your dealer To start and stop when you select oil.

  • Page 19: To Operate The Grass Trimmer

    To clear grass with a grass blade these instructions can cause damage to the engine. 1. Keep your feet apart during operation of the product. 5. Set the choke control to the run position, then pull Make sure feet are tightly against the ground. the start rope until the engine starts.

  • Page 20: Maintenance

    To sweep the grass line to prevent unbalance and vibrations in the handles. Also do a check of the other The airflow from the rotating trimmer line can be used to parts of the trimmer head and clean it if remove cut grass from an area.

  • Page 21: To Adjust The Idle Speed

    Maintenance schedule Daily Weekly Monthly Clean the external part of the spark plug. Remove it and check the electrode gap. Adjust the distance to 0.6-0.7 mm or replace the spark √ plug. Install a suppressor to the spark plug. Clean the cooling system. √...

  • Page 22: Troubleshooting

    Make sure that the air filter is clean. • If the spark plug is dirty, clean it and make sure that 7. Use Husqvarna two-stroke oil to put oil on the filter. Technical data the electrode gap is correct, refer to Make sure that you remove excessive oil before you on page 23 .

  • Page 23: Transportation And Storage

    Keep the product and equipment in a dry and frost- does not keep moisture. proof area. • Keep the product tightly attached during transport. • Clean the product. Technical data unit 333R Mark II 333RB Mark II Engine specifications Cylinder displacement 32.6 32.6 1157 - 009 - 21.03.2025...
  • Page 24 Cylinder bore 36.0 36.0 Stroke 32.0 32.0 Idling speed 3000±300 3000±300 Maximum speed 10600 10600 Speed of output shaft 7800 7800 Maximum engine output kW/rpm 1.0/7000 1.0/7000 Spark plug NGK BPMR7A NGK BPMR7A Electrode gap 0.6-0.7 0.6-0.7 Fuel tank capacity 1100 1100 Vibration data...

  • Page 25: Accessories

    GZ32B representing model(s) certificates are applicable to all manufacturing locations Husqvarna 333R Mark II, 333RB Mark II, from 2024 and Countries of Origin, as stated on the product. The serial numbers and onwards. The platform number and...

  • Page 26: Appendix

    593707601 1157 - 009 - 21.03.2025...
  • Page 27 1157 - 009 - 21.03.2025...
  • Page 28 Original instructions 1144653-26 Rev. A 2025-03-25...

This manual is also suitable for:

333rb mark ii