Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for General Pipe Cleaners JM-3080
Summary of Contents for General Pipe Cleaners JM-3080
- Page 1 OPERATOR'S MANUAL FOR JM-3080 GAS JET COLD WATER PRESSURE WASHER CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! This manual is an important part of the pressure washer and must remain with this unit! Operator's Manual ©Copyright 2006 Form #37-1154-E/S-032725...
-
Page 2: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ......................3 IMPORTANT SAFETY INSTRUCTIONS .................4 FEATURES ........................7 INSTALLATION & PREPARATION ..................8 OPERATION ........................12 MAINTENANCE ......................16 TROUBLESHOOTING ....................17 NOTES ...........................19 FRAME ASSEMBLY ......................20 PUMP/GEARBOX ASSEMBLY ..................22 PUMP ASSEMBLY ......................24 HOSE REEL ASSEMBLY ....................26 FUEL TANK ASSEMBLY ....................28 WATER TANK ASSEMBLY ....................30 WARNING WARNING: This product can expose you to... -
Page 3: Introduction
INTRODUCTION Your JM-3080 Jet-Set gas-powered water jet is designed to give you years of trouble-free, profitable service. However, no machine is better than its operator. Read, understand and follow all safety warnings and instructions provided with the product. Failure to follow the warnings and instructions may result in electric shock and/or serious injury. -
Page 4: Important Safety Instructions
PERSONNEL WITH SAFE OPERATION MAINTENANCE PROCEDURES FOR THE JM-3080. RISK OF ASPHYXIATION Serious injury or death may occur from inhaling engine exhaust or danger- ous vapors. Use this product only in a well ventilated area. This water jet is designed for outdoor use only. Always make sure there is adequate ventila- tion (fresh outside air) for breathing and combustion. - Page 5 IMPORTANT SAFETY INSTRUCTIONS PERSONAL SAFETY 1. High pressure developed by jet machines will cause personal injury. Water spray should not be pointed at any person. High pressure spray can result in serious injury. If fluid seems to have penetrated the skin, seek emergency medical attention at once.
- Page 6 IMPORTANT SAFETY INSTRUCTIONS in upright position or oil may leak from pump. If low, fill with SAE 30 weight non-detergent oil. • Gas jets are shipped with oil in the engine. Consult motor manufac- turer’s guide for oil requirements. • Jet machines are meant to be used at or near the working area and under operator supervision.
-
Page 7: Features
FEATURES Swivel 400 ft. Hose Reel Pressure Gauge Output Valve Hose Reel Release Knob Pump Engine Water Inlet Inlet Filter Battery Box 12 Gallon Buffer Tank Pulse Valve Buffer Tank Outlet Valve Operator's Manual... -
Page 8: Buffer Tank
• Battery should have lifting strap for easy installation. BUFFER TANK The JM-3080 is equipped with a 12 gallon buffer tank. If the incoming water flow is less than 8 gpm required by the pump, the buffer tank will protect the pump from cavatation and damage. - Page 9 INSTALLATION & PREPARATION 2. Make sure the nozzle you are using matches the pump size. A 3000 psi pump requires a different nozzle orifice than a 1500 psi pump. Mismatching nozzles with pump size will either cause too little pressure, which may not clear the drain, or too much pressure, which may damage the machine.
- Page 10 INSTALLATION & PREPARATION NOZZLE SELECTION GUIDE HOSE SIZE 1/4" 3/8" CAT# CAT# Thruster Nozzle JN-101 JN-111 Flusher Nozzle JN-102 JN-112 High Thrust Degreaser Nozzle JN-103 JN-113 Monster Nozzle JN-104 JN-114 Rotary Nozzle (Optional) JNRB-7 JNRB-11 Chain Saw Nozzle (Optional) JCSN-11 Operator's Manual...
- Page 11 WARNING THE FOLLOWING PAGES CONTAIN OPERATING AND MAINTENANCE INSTRUCTIONS. DO NOT ATTEMPT TO OPERATE THIS PRESSURE WASHER UNTIL YOU HAVE READ AND UNDERSTOOD ALL SAFETY PRECAUTIONS AND INSTRUCTIONS LISTED IN THIS MANUAL. INCORRECT OPERATION OF THIS UNIT CAN CAUSE SERIOUS INJURY!! DO NOT ALTER OR MODIFY THIS EQUIPMENT IN ANY MANNER! Operator's Manual...
-
Page 12: Operation
OPERATION SET-UP 1. Locate the jet near the drain line on a level surface with drainage. Tip: Ideally, the drain line should be cleared from the downstream side, that is, from the street back toward the house. If you must clear the line from the drain toward the street, you may need to use a siphon pump to clear away excess water. -
Page 13: Shut Down Instructions
OPERATION 10. When the jet hose encounters a bend, it’s advance will usually slow or stop. The hose has a slight bend in it from the hose reel. It may be necessary to manually feed or rotate the jet hose to work it around the bends. If the hose won’t advance, put the hose in a loop and rotate it a quarter to half turn so the curve of the hose matches the pipe. - Page 14 OPERATION attach a short garden hose (not to exceed four feet) to inlet on the pump and put other end into the anti-freeze container. Be sure to remove the nozzle from the hose. Turn the machine on to draw anti-freeze into the system. When anti-freeze flows out of the end of the hose, turn the machine off.
- Page 15 OPERATION For remote operation, pull the hose from the hose reel to the drain site. At- tach the hose to the inlet of the pedal. The pedal is designed for 3/8” hose fittings. If using a 1/4” hose, use the AD-1 adapter, as well. Then, attach the smaller hose (1/8”...
-
Page 16: Maintenance
MAINTENANCE WARNING: DISCONNECT JETTER FROM POWER SOURCE BEFORE PERFORMING MAINTENANCE OR MAKING ANY ADJUSTMENTS. Regular inspection is the key to preventing breakdowns and prolonging the life of the equipment. Follow this simple procedure religiously. DAILY • Check INLET FILTER for debris before each use. •... -
Page 17: Troubleshooting
TROUBLESHOOTING PROBLEM PROBABLY CAUSE SOLUTION Low Pressure. Wrong, clogged, or oversized nozzle. Clean or replace worn nozzle. Check nozzle size. Clogged water inlet strainer. Clean or replace strainers. Inadequate water supply. Make certain water supply valve is on fully. Make certain water supply hose is at least 3/4”... - Page 18 TROUBLESHOOTING PROBLEM PROBABLY CAUSE SOLUTION Detergent solution Clogged detergent strainer. Clean or replace strainer. too weak. Air leak in detergent suction tube or inlet Find air leak and clean or replace parts as plumbing. necessary. Detergent solution Original detergent too concentrated. Dilute product as necessary to achieve proper too concentrated.
-
Page 19: Notes
NOTES DATE SERIAL NUMBER REASON FOR CHANGE 08/05/2015 28003283 Unloader Change, Ball Valve Change 01/29/2019 28006259 Changed Hose Reel Operator's Manual... -
Page 20: Unit Assembly
UNIT ASSEMBLY 27 26 20 21 22 24 18 42 43 44 46 47 65 64 24 62 18 19 31" 89 87 DETAIL A Operator's Manual... - Page 21 JM-3080-0AH_0AM 112124 UNIT ASSEMBLY ITEM DESCRIPTION PART # ITEM DESCRIPTION PART # DECAL - JM-3080 FRONT PANEL (SEE JM71-0004) HANDLE GRIP JM7-0227 BOLT JM27-0066 ELBOW JM24-0118 WASHER (0AH) JM28-0003 DECAL - RISK OF BURNS (SEE JM71-0004) WASHER (0AM) JM28-0003 DECAL - 670CC REWIND GPC (0AM)
-
Page 22: Pump/Gearbox Assembly
PUMP/GEARBOX ASSEMBLY Operator's Manual... -
Page 23: Item Description
3-0368 051811_T AJH PUMP / GEARBOX ITEM DESCRIPTION Mi-T-M # GEARBOX JM47-0031 PUMP JM3-0300 VALVE CAP JM46-1430 Operator's Manual... -
Page 24: Pump Assembly
PUMP ASSEMBLY TORQUE SPECS ITEM FT/LBS 36.8 50.2 18.1 Operator's Manual... - Page 25 3-0300 031114 PUMP ASSEMBLY ITEM DESCRIPTION Mi-T-M # ITEM DESCRIPTION Mi-T-M # HEAD BOLT JM27-8470 SIDE COVER W/ SIGHT GLASS JM46-0918 WASHER JM29-0155 SHIM 0.05MM JM46-0947 O-RING JM25-0647 SHIM 0.10MM JM46-0948 COMPLETE VALVE (SEE KIT JM70-0584) SEE KIT SHIM 0.19MM JM46-0949 VALVE CAP JM39-0242...
-
Page 26: Hose Reel Assembly
HOSE REEL ASSEMBLY Operator's Manual... - Page 27 851-0390 111023 HOSE REEL ASSEMBLY ITEM TITLE PART # LOCKNUT JM30-0157 WASHER JM28-0003 3/8” SWIVEL JM24-0362 PRESSURE HOSE JM15-0257 ELBOW JM24-0105 SCREW COUPLER JM23-0490 BOLT JM27-0016 ISOLATOR JM14-0069 WASHER JM28-0002 LOCKNUT JM30-0155 HOSE REEL STAND JM20-1221A18 BOLT JM27-0066 HANDLE GRIP JM7-0059 HOSE REEL JM50-0221...
-
Page 28: Fuel Tank Assembly
FUEL TANK ASSEMBLY 27" - HONDA 37" - MITM 18" TO ENGINE AIR CLEANER 28" Operator's Manual... - Page 29 FUEL TANK ASSY - JM-3080 102622 FUEL TANK ASSEMBLY ITEM TITLE PART # FUEL HOSE *(FOUR FEET REQUIRED) (0AH) JM15-0008 FUEL HOSE *(FIVE FEET REQUIRED) (0AM) JM15-0008 CLAMP WORM JM42-0004 BARB JM23-0051 FUEL PICK-UP JM33-0352 JM23-0409 O-RING JM25-0427 BULKHEAD FITTING...
-
Page 30: Water Tank Assembly
WATER TANK ASSEMBLY TO UNLOADER BYPASS TO BALL VALVE 13.75" 6.5" TO INLET FILTER 26" O-RING TO PUMP INLET 26" Operator's Manual... - Page 31 WATER TANK ASSY - JM-3080 013019 WATER TANK ASSEMBLY ITEM TITLE PART # HOSE BARB JM23-0360 HOSE *(ONE FOOT REQUIRED) JM15-0007 HOSE CLAMP JM42-0011 ELBOW JM23-0119 HOSE *(TWO FEET REQUIRED) JM15-0007 JM23-0127 JM23-0409 O-RING JM25-0427 BULKHEAD FITTING JM23-0408 WATER TANK...
- Page 32 General Wire Spring Co. 1101 Thompson Avenue McKees Rocks, PA 15136 412-771-6300 www.drainbrain.com Operator's Manual...
Need help?
Do you have a question about the JM-3080 and is the answer not in the manual?
Questions and answers