Related Manuals for Kohler K-1166-C1-96
Summary of Contents for Kohler K-1166-C1-96
- Page 1 Installation Guide Overflowing Bath Français, page “Français-1” Español, página “Español-1” 1054216-2-C...
-
Page 2: Important Product Information
Do not relocate the pump, or make other modifications to the circulating system, as this could adversely affect the performance and safe operation of your bath. Kohler Co. shall not be liable under its warranty or otherwise for personal injury or damage caused by any such unauthorized modification. -
Page 3: Tools And Materials
All information in this manual is based upon the latest product information available at the time of publication. At Kohler Co., we constantly strive to improve the quality of our products; we therefore reserve the right to make changes in product characteristics, packaging, or availability at any time without notice. - Page 4 When using the K-922 or K-923 Laminar Bath Spout with drip tray K-924, the distance from the finished wall to the outside wall of overflow channel should not exceed 2″ (51 mm). Kohler Co. reserves the right to make revisions in the design of products without notice, as specified in the Price Book.
-
Page 5: List Of New Terms
The suction cover must always be installed during product use to ensure user safety. Pump - The pump circulates the water. Wire harness - The wire harness connects all powered peripheral components (valves, pump, heater, switches, lights) to the master control. Kohler Co. 1054216-2-C... -
Page 6: Roughing-In Information
W x 15″ (381 mm) H. Refer to the roughing-in diagram for suggested access panel location. Make sure the flooring is in good condition and offers adequate support for your bath. IMPORTANT! Verify that the subfloor is flat and level. This will help minimize the leveling adjustments necessary for proper product performance. 1054216-2-C Kohler Co. -
Page 7: Construct The Stud Framing
fill spout and the top of the bathing well rim. Take into account the thickness of your planned finished deck material, and construct the framing and deck material with this minimum air gap in mind. Kohler Co. 1054216-2-C... -
Page 8: Install The Rough Plumbing
Install the drain according to the drain manufacturer’s instructions. Do not connect the trap at this time. Position a clean drop cloth or similar material in the bottom of the bath. Be careful not to scratch the surface of the overflowing bath. 1054216-2-C Kohler Co. -
Page 9: Position The Unit
Make sure all six adjustable feet rest directly on the subfloor, and make sure the bathing well rim is level within 1/8″ (3 mm) in all directions. Cut and discard the banding straps from the pump. Make sure the rubber isolation feet are in place. Insert the drain tailpiece into the trap. Kohler Co. 1054216-2-C... -
Page 10: Install The Plumbing
Make sure all butterfly valves and supply connections are tightened securely. Open the hot and cold water supplies and check the supply connections for leakage. Run water into the bathing well, and check the drain connections for leakage. 1054216-2-C Kohler Co. -
Page 11: Make The Electrical Connections
Follow local electrical codes. Bond in accordance with national and local codes. A wiring harness has been pre-wired at the factory, allowing communication between the keypad, all features, and the control. No additional wiring is required, but ensure that all wires are securely fastened. Kohler Co. 1054216-2-C... - Page 12 Make the Electrical Connections (cont.) NOTE: Your wiring harness includes an antenna for the optional remote control. Do not alter or damage this antenna during installation. *Outside North America, this device may be known as a Residual Current Device (RCD). 1054216-2-C Kohler Co.
-
Page 13: Test The Control Switch
(after approximately 1/2 minute) until the overflowing bath is drained or restarted. NOTE: For additional information on operation of your bath, see the ″Using Your Bath″ section. IMPORTANT! Allow adequate access to each of the six adjustable feet until test run is complete. Kohler Co. 1054216-2-C... -
Page 14: Using The Remote Control
The heater will not operate if the pump is off. If the heater is on, the pump switch will be dark green. If the heater is off, it will be yellow-green. To cycle the chromatherapy lights through the spectrum of colors, press the chromatherapy cycle icon. To lock an individual chromatherapy color in, press the chromatherapy specific color icon. 1054216-2-C Kohler Co. -
Page 15: Complete The Finished Wall Or Deck
Remove plaster by carefully scraping with a wood edge. Do not use metal scrapers, wire brushes, or other metal tools. Use a powder-type detergent on a damp cloth to provide mild abrasive action to any residual plaster. Kohler Co. 1054216-2-C... -
Page 16: Using Your Bath
1/2 minute until the overflowing bath is drained below the overflow channel sensors or restarted. NOTE: A built-in timer automatically stops the bath after approximately 20 minutes of operation. 1054216-2-C Kohler Co. -
Page 17: Chromatherapy Light Operation
For warranty service, contact your dealer or wholesale distributor. This Troubleshooting Guide is for general aid only. Contact a Kohler Authorized Service Representative or a qualified electrician to correct all electrical problems. For warranty service, contact your dealer or wholesale distributor. - Page 18 A. Turn on the power. rim upon filling. B. Level probe wires loose. B. Check/reconnect wires. C. Butterfly valves do not work. C. Check wiring; replace butterfly valves if necessary. D. Control switch does not work. D. Replace control. 1054216-2-C Kohler Co.
Need help?
Do you have a question about the K-1166-C1-96 and is the answer not in the manual?
Questions and answers