Advertisement
INSTALLATION MANUAL
CameraView (PM-65 Camera with
Auxiliary Cameras and Monitor)
Document ID: IM-DC-X4M
Last Updated: November 25, 2024
Pedigree Technologies recommends using a professional installer for optimal
results. Please let your Pedigree Technologies representative suggest a provider if
you need help with your hardware installations.
PedigreeTechnologies.com | Support: (701)-499-0022
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pedigree Technologies CameraView PM-65
Summary of Contents for Pedigree Technologies CameraView PM-65
- Page 1 Auxiliary Cameras and Monitor) Document ID: IM-DC-X4M Last Updated: November 25, 2024 Pedigree Technologies recommends using a professional installer for optimal results. Please let your Pedigree Technologies representative suggest a provider if you need help with your hardware installations. PedigreeTechnologies.com | Support: (701)-499-0022...
-
Page 2: Required Information
• Split windows may have to adjust mounting location other than what is recommended in this document. Consult with your implementation manager at Pedigree Technologies. • DO NOT INSERT YOUR OWN SD CARD - SD Cards must be properly formatted for use with the camera. If you need a new SD Card or want to increase the size of the SD Card, PLEASE CONTACT YOUR ACCOUNT MANAGER. -
Page 3: Power Cable
CameraView PM-65 Aux & Monitor Installation Steps, Continued Dry Fit Determine proper placement of camera on the front windshield. (Dry fit only. It’s important to run cabling to power source and determine where it will fit properly.) • High on the windshield next to the rearview mirror area left of center divider •... - Page 4 CameraView PM-65 Aux & Monitor Installation Steps, Continued Installation - Molex Plug Connect the Molex end of the power cable to the “Camera” plug on the Accessory Harness on the back of the Cab-Mate Flex. Exterior Camera Splitter/Power Cable Accessory...
- Page 5 CameraView PM-65 Aux & Monitor Direct Wire Installation Option STEP ONE Cut off the 10-pin molex connector from the power cable. Not used Exterior Camera Splitter/Power Cable STEP TWO The Black wire (ground) should be securely fastened to a grounded screw or chassis ground.
- Page 6 CameraView PM-65 Aux & Monitor Connect Power to Camera w/Auxiliary Cameras CABLE TO CAMERA Connect the Exterior Camera Splitter/Power Cable to Exterior Camera Splitter/ Power Cable the camera ports for Power and TVI. The plugs will fit the ports appropriately and you cannot put the wrong plug in the wrong port.
- Page 7 CameraView PM-65 Aux & Monitor Optional Auxiliary Cameras Before You Begin TIPS FOR AUXILIARY CAMERA MOUNTING • Placement of Auxiliary Cameras will be unique to your needs and your assets. Installation will be just as varied. The following tips are not meant to be exact steps. Use your judgement for placement, weatherproofing, sealing etc.
- Page 8 CameraView PM-65 Aux & Monitor Connect Y Splitters Exterior Camera Splitter/ Power Cable SPLITTER TO POWER Connect the splitter end labled “CDR” to the TVI ports on the Exterior Camera Splitter/Power cable. It is important to record which Aux camera is tied to which TVI port.
- Page 9 CameraView PM-65 Aux & Monitor Optional Auxiliary Cameras STEP ONE Auxiliary camera can be mounted around a side mirror mounting bar or fastened with screws by removing the clam bracket. The underside of the camera has grooves to grab on to a mounting bar in multiple directions.
- Page 10 CameraView PM-65 Aux & Monitor Monitor Power and Mount The colors from the Monitor wiring harnesses and the wiring from the Camera power harness DO NOT MATCH. The wires from the harnesses may be twisted together and terminated in the appro- priate location.
- Page 11 CameraView PM-65 Aux & Monitor Optional Auxiliary Cameras SELECT LOCATION Select a mounting location(s) for the Auxiliary Camera(s). Side view camera are usually mounted on the side mirrors. The camera cabling will need to run through the door into the cab to connect to the camera as it is mounted on the windshield.
- Page 12 CameraView PM-65 Aux & Monitor Optional Auxiliary Cameras WIRING Choosing the proper placement for wiring is dependent on the asset that the camera is installed on. Some possibilities are running through existing conduite holes, paneling, A-pillar, and inside paneling. Caution should be taken when drilling holes, including making sure to weatherproof all drill holes with gaskets and silicone.
-
Page 13: Mount Camera
CameraView PM-65 Aux & Monitor Installation Steps, Continued Mount Camera STEP ONE Determine proper placement of camera on the front windshield. • Center of the windshield next to the rearview mirror area • Highest possible placement within the wiper blade path •... - Page 14 CameraView PM-65 Aux & Monitor Mount Camera continued STEP FIVE Orient the camera to the windshield. • Camera should be level to the horizon line. • Point the lens forward with a slight downward angle so the camera picks up the front hood at the bottom of the frame.
- Page 15 CameraView PM-65 Aux & Monitor Installation Steps, Continued Set Camera Position STEP ONE Download the CameraView Setup App from the Google Playstore (Android only) and allow all necessary permissions. STEP TWO Choose Camera IMEI and add the camera’s serial number (located under the front faceplate of the camera).
- Page 16 CameraView PM-65 Aux & Monitor Installation Steps, Continued Set Camera Position STEP THREE Once connected, the Select View option will allow you to choose the cameras to align. ROAD & DRIVER The road facing camera will have a line for the horizon to help you line up...
-
Page 17: Mounting Tips
CameraView PM-65 Aux & Monitor Mounting Tips GOOD MOUNTING TIPS • Metrics visual detection happens within red square area (image right) • Horizon line must be level with more road than sky • Field of view in green area •...
Need help?
Do you have a question about the CameraView PM-65 and is the answer not in the manual?
Questions and answers