1369/2017......................44 WE’RE THINKING OF YOU Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it decades of professional experience and innovation. Ingenious and stylish, it has been designed with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great results every time.
ENGLISH SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damage that are the result of incorrect installation or usage. Always keep the instructions in a safe and accessible location for future reference.
– working environments; by clients in hotels, motels, bed & breakfast and – other residential type environments; areas for communal use in blocks of flats or in – launderettes. Do not exceed the maximum load of 8 kg (refer to the •...
ENGLISH • Follow the installation instructions • Connect the mains plug to the mains supplied with the appliance. socket only at the end of the • Do not use the appliance before installation. Make sure that there is installing it in the built-in structure due access to the mains plug after the to safety manner.
It can damage rubber • Disconnect the appliance from the parts of the washing machine. mains electrical and water supplies. Prewash such fabrics by hand before • Cut off the mains electrical cable loading them into the washing close to the appliance and dispose of machine.
Page 7
ENGLISH 3.3 Unpacking WARNING! Use the gloves. WARNING! Remove all the packaging and the transit bolts before installing the appliance. 1. Put two polystyrene packaging elements on the floor under the appliance. WARNING! It is strongly recommended that this action is carries out by two persons.
Page 8
5. Remove the power supply cable and the drain hose from the hose holders. It is possible to see water flowing from the drain hose. This is due to the testing with water of the appliance in factory. 6. Remove the three bolts, the hose holders and plastic spacers by using the spanner supplied with the appliance.
ENGLISH 3.4 Positioning and levelling 1. Install the appliance on a flat hard floor. WARNING! Make sure that carpets do not stop the air circulation below the appliance. Bring the appliance near the furniture recess before levelling it. For more details, refer to paragraph "Building in".
The inlet hose 1. Remove the inlet hose from inside the drum. 2. To connect the water inlet hose towards the proper direction and with the proper inclination, check the position of the water tap before connecting it to the back of the appliance.
Page 11
ENGLISH To a stand pipe with vent-hole Directly into a drain pipe at a height of not Ø 40 mm less than 60 cm (23.6”) and not more than 100 cm (39.3”). The end of the drain hose must always be ventilated , i.e.
If hoses run behind the 596 mm appliance, make sure that 553 mm nothing closes the small recess indicated with the measures 50 x 50 mm. 819 mm 50 mm 50 mm 140 mm 76 mm The appliance is also equipped with an adhesive sponge pad H that you can find inside the drum.
Page 13
ENGLISH Factory pre setting The appliance is originally pre set for the assembly of a cupboard door opening from right to left. The best solution would be to screw the upper hinge to the upper hole of the top plate and the lower hinge to the lower hole of the bottom plate.
Page 14
Cupboard door preparation For countersinking the door, it is recommended to call a professional. Align the cupboard door to the furniture correctly. Measure the distance X to fix the height of the hole to countersink the upper hinge. The centre of the hole Y should be at the same height of the stroke on the hinge support.
ENGLISH Mounting the door Fix the hinges to the hinge supports on the appliance by means of the two supplied screws B. The hinges can be adjusted to compensate for possible uneven thickness of the door. Counter-magnet The appliance is pre set for a magnetic closure.
Front feet for levelling the appliance Inlet hose connection Drain hose Back feet for levelling the appliance Mains cable 5. CONTROL PANEL 5.1 Control panel description Time Temperatura Manager Partenza Centrifuga Ritardata Extra Vapore Prelavaggio Macchie Più Morbido Risciacquo Finale On/Off...
Page 17
ENGLISH 5.2 Display The Temperature area: Temperature indicator . Cold water indicator. Child safety lock indicator. Door locked indicator. Delay start indicator. The digital indicator can show: • Programme duration (e. g. • Delay time (e. g. • Cycle end ( •...
Add garments indicator. it lights at the beginning of the wash‐ ing phase, when it is still possible to pause the appliance and add more laundry. Maximum load indicator (refer to "The SensiCare System load detection " paragraph). It flashes when the laundry load exceeds the maximum declared load of the selected programme.
Page 19
ENGLISH 6.7 Macchie turns regularly to reduce creasing. You must drain the water to unlock Touch this button to add the stain phase the door. to a programme. If you touch the Avvio/Pausa The corresponding indicator above the button, the appliance performs the touch button illuminates.
6.10 Vapore Finale appliance begins the countdown and the door is locked. This option adds a steam phase followed by a short anti-crease phase at the end 6.13 Time Manager of the washing programme. With this option you can reduce the...
ENGLISH When setting a steam programme, this 6.14 Avvio/Pausa button allows to chose three steam levels and the programme duration is reduced Touch the Avvio/Pausa button to accordingly: start, pause the appliance or interrupt a • : maximum. running programme. •...
Page 22
• Items that are not suitable for tumble drying. • All items with plastic, metal, wooden parts or alike. ELECTROLUX fragrance. If you use this special gentle fragrance, your laundry will scent as just washed: pour a single dose bottle in the compartment and simply start a steam programme.
Page 23
ENGLISH Programme Reference Maxi‐ Programme description Default tem‐ spin (Type of load and soil level) perature speed load Temperature Spin range speed range 1 kg Cottons, Synthetics, Delicates. Short and gentle steam programme to refresh even your Freshscent very delicate garments, including very delicate garments with sequins, lace etc.
Page 24
Programme Reference Maxi‐ Programme description Default tem‐ spin (Type of load and soil level) perature speed load Temperature Spin range speed range 1200 rpm 2 kg Do not use fabric softener and (1200- 400 Outdoor make sure that there is no soften‐...
Page 25
ENGLISH Programme Reference Maxi‐ Programme description Default tem‐ spin (Type of load and soil level) perature speed load Temperature Spin range speed range 1200 rpm 1.5 kg Machine washable wool, hand washable (1200 - wool and other fabrics with «hand washing» Lana/Seta 400 rpm) care symbol...
ENGLISH If you deactivate the acoustic signals, they continue to operate when the appliance has a malfunction. 9. BEFORE FIRST USE 1. Make sure that the electrical power is 4. Set and start a programme for cotton available and the water tap is open. at the highest temperature without 2.
10.3 Filling the detergent and 10.4 Check the position of the additives detergent flap 1. Pull out the detergent dispenser until it stops. - Compartment for prewash phase, soak programme or stain re‐ 2. Press the lever down to remove the mover.
ENGLISH display and the given information changes accordingly. If a selection is not possible an acoustic signal sounds and the display shows 10.7 Starting a programme Touch the Avvio/Pausa button to start the programme. It is not possible to start the programme when the indicator Make sure that the flap does not cause a of the button is off and doesn't flash (e.g.
The display At the end of the load detection, in case shows the indicator of drum overload, the indicator When the countdown is completed, the flashing in the display: programme starts automatically. In this case, for 30 seconds, it is possible 2.
ENGLISH 2. Press the button On/Off again to acoustic signals operate (if they are activate the appliance. active). The display shows If the SensiCare System has The indicator of the Avvio/Pausa completed and the water button goes off. filling has already started, the new programme starts The door unlocks and the indicator without repeating the...
Press the button On/Off to activate The option indicator Rinse Hold the appliance again. disappears. • 5 minutes after the end of the washing programme. If you have set Extra Silent Press the On/Off button to activate and the spin speed is not the appliance again.
ENGLISH • Follow the instructions that you find on packaging of the detergents or other treatments without exceeding the indicated maximum level ( • Use the recommended detergents for the type and colour of the fabric, the programme temperature and the level of soil.
12.2 Descaling Regularly examine the seal and remove all objects from the inner part. Coins, If the water hardness in your buttons, other small items forgotten in area is high or moderate, we the pockets of your clothes are deposited...
ENGLISH 1. Open the drawer. Press the catch 4. Insert the detergent drawer into the downwards as indicated in the guide rails and close it. Run the picture and pull it out. rinsing programme without any clothes in the drum. 2.
Page 36
Proceed as follows to clean the pump: 1. Open the pump cover. 2. Place a suitable bowl below the drain pump access to collect the water that flows out. Always keep a rag nearby to dry up any water spillages when removing the filter.
Page 37
ENGLISH 6. Turn the filter anti-clockwise to remove it 7. If it is necessary, remove fluff and objects from the filter recess. Make sure that the impeller of the pump can rotate. If it does not rotate, contact the Authorised Service Centre. 8.
10. Close the pump cover. When you drain the water with the emergency drain procedure, you must activate the drain system again: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water.
ENGLISH 12.10 Frost precautions 4. Empty the drain pump. Refer to the emergency drain procedure. If the appliance is installed in an area 5. When the drain pump is empty, where the temperature can reach values install the inlet hose again. around 0°...
13.2 Possible failures Problem Possible solution • Make sure that the mains plug is connected to the mains socket. • Make sure that the appliance door is closed. • Make sure that there is no damaged fuse in the fuse box.
Page 41
ENGLISH Problem Possible solution • Make sure that the sink spigot is not clogged. • Make sure that the drain hose has no kinks or bends. • Make sure that the drain filter is not clogged. Clean the filter, if necessary. Refer to "Care and cleaning". The appliance does not •...
Problem Possible solution • Increase the detergent quantity or use a different deter‐ gent. The washing results are • Use special products to remove the stubborn stains be‐ not satisfactory. fore you wash the laundry. • Make sure that you set the correct temperature.
ENGLISH 4. Take out the laundry and then close the appliance door. 14. CONSUMPTION VALUES Stated values are obtained in laboratory conditions with relevant stand‐ ards. Different causes can change the data: the quantity and type of laundry and ambient temperature. Water pressure, the supply voltage and the temperature of inlet water may also affect the washing pro‐...
16. PRODUCT INFORMATION SHEET IN REFERENCE TO E.U. REGULATION 1369/2017 Product Information Sheet Trade Mark ELECTROLUX Model EW7F384BI, PNC914580013 Rated capacity in kg Energy efficiency class A+++ Energy consumption in kWh per year, based on 220 standard washing cycles for cotton programmes at 60 °C and 40 °C at full and partial load, and the con‐...
ENGLISH Energy consumption of the standard 60°C cotton pro‐ 0.82 gramme at full load in kWh Energy consumption of the standard 60°C cotton pro‐ 0.56 gramme at partial load in kWh Energy consumption of the standard 40°C cotton pro‐ 0.53 gramme at partial load kWh Power consumption of the off-mode in W 0.30...
Need help?
Do you have a question about the EW7F384BI and is the answer not in the manual?
Questions and answers