Advertisement

Quick Links

//
HIGHLAND
PROFESSIONAL SERIES
// MODELS : HP4SSN/L & HP6SSN/L
Appliance Operation Manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PROFESSIONAL HP4SSN and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Highland PROFESSIONAL HP4SSN

  • Page 1 HIGHLAND PROFESSIONAL SERIES // MODELS : HP4SSN/L & HP6SSN/L Appliance Operation Manual...
  • Page 2: Professional Series

    // MODELS: HP4SSN/L & HP6SSN/L Your HIGHLAND cooktop is a state of the art appliance featuring the latest in flame failure auto safety shut off. Should the flame on any of the four/six burners be extinguished accidentally then the gas flow to that burner will automatically cease to flow, thereby ensuring no hazardous build-up of flammable gas from the cooktop.
  • Page 3 IMPORTANT ENSUrE THAT THE bUrNErS ArE cOrrEcTLY ASSEMbLED PrIOr TO USING THIS APPLIANcE. UNEvEN fLAMES MAY INDIcATE THAT THE bUrNErS HAvE NOT bEEN ASSEMbLED cOrrEcTLY.
  • Page 4 1) Ensure that the locating pin ‘A’ on the distributor ring is securely located in the recess hole of the WOK burner body. This is easily achieved by placing the distributor ring on the WOK burner body and then rotating the distributor until the locating pin ‘A’...
  • Page 5: Operation

    // OPERATION – GAS CONTROLS It is important that the burner assembly sequence, detailed on the previous page, is performed prior to initial operation of the cooktop. WHEN INSTALLED IN A cArAvAN Or MArINE crAfT DO NOT USE THIS APPLIANcE AS A SPAcE HEATEr. DO NOT PLAcE cOMbUSTIbLE MATErIAL Or PrODUcTS ON THIS APPLIANcE AT ANY TIME.
  • Page 6 Maximum Position – WOK burner controls Maximum Position – A and b burner controls 3. Press and hold the control knob down firmly for a full 3 seconds to ensure the flame failure device engages. If the flame goes out after you release the knob then the flame failure device did not engage – simple press down firmly again, turn to the max position and keep pressing down for a full 3 seconds.
  • Page 7 LEGEND – GAS CONTROL GRAPHICS – WOK BuRNER both inner and outer burners are operating at maximum output The inner burner remains on full output, but the outer burner is on minimum output The inner burner is on full output and the outer burner is extinguished The inner burner is on minimum output and the outer burner remains extinguished Legend –...
  • Page 8: Manual Ignition

    MANuAL IGNITION If there is no power to the appliance or your area is experiencing a power ‘black-out’ simply strike a match or spark igniter next to the required burner and follow steps 1 and 2 (above). NOTE: THE fLAME fAILUrE SAfETY SYSTEM IS INDEPENDENT Of POWEr AND WILL STILL OPErATE WITHOUT A POWEr SOUrcE.
  • Page 9: Maintenance

    MAINTENANCE We recommend that your appliance should be regularly serviced every 5 years to ensure the continued safe and reliable operation of your appliance. This is only to be conducted by an authorised service agent. Please note a nominal fee will be charged for this maintenance call.
  • Page 10 After cleaning (especially in a dishwasher) please ensure that the ports (burner heads) are free of any food, water or debris. These can be easily cleaned/cleared with a toothpick or needle. NOTE: DO NOT UNScrEW ANY PArT Of THE bUrNEr SYSTEM. THIS SHOULD ONLY bE DONE bY AN AUTHOrISED PErSON.
  • Page 11: Fault Finding/Abnormal Operation

    FAuLT FINDING/ABNORMAL OPERATION FAuLT POSSIBLE SOLuTION(S) burner lights, but goes out when - control knob is to be pressed down firmly, and held firmly, during ignition procedure control knob is released for 3 full seconds - control knob is ‘bottoming out’ on the control panel and not engaging the flame failure device –...
  • Page 12: Safety Instructions

    SAFETY INSTRuCTIONS 1) THIS APPLIANcE IS NOT INTENDED fOr USE bY YOUNG cHILDrEN Or INfIrM PErSONS, WITHOUT SUPErvISION. YOUNG cHILDrEN SHOULD bE SUPErvISED TO ENSUrE THAT THEY DO NOT PLAY WITH THE APPLIANcE. 2) STEAM cLEANErS SHOULD NOT bE USED. 3) If THE SUPPLY cOrD IS DAMAGED, IT MUST bE rEPLAcED bY THE MANUfAcTUrEr Or ITS SErvIcE AGENT Or A SIMILArLY qUALIfIED PErSON IN OrDEr TO AvOID A HAzArD.
  • Page 13: Installation Instructions

    INSTALLATION INSTRuCTIONS Your HIGHLAND cooktop must be installed in accordance with the installation requirements of the local gas and electrical authorities or the appropriate installation guide issued by the A.L.P.G.A. and A.G.A. (reference code AS5601), or the building authorities requirements.
  • Page 14 Determine the position where your HIGHLAND appliance is to be mounted, ensuring no structural members interfere with the space requirements. Note: Ensure that there is at least 750mm clearance between the benchtop and any overhead downward facing surface located over the cooktop (such as a rangehood or cupboard), or at least 780mm between the benchtop and an overhead exhaust fan.
  • Page 15 NOTE: DO NOT OvEr TIGHTEN brAcKETS AS THIS MAY DISTOrT THE APPLIANcE. NOTE: cONNEcTION Of THE APPLIANcE TO THE GAS SUPPLY MUST bE IN AccOrDANcE WITH THE rEqUIrEMENTS Of AS5601. A _ INcH bPS cONNEcTOr AT THE INLET IS rEcOMMENDED AND THE GAS SUPPLY LINE TO THE APPLIANcE MUST bE Of ADEqUATE LENGTH TO ALLOW SUffIcIENT WITHDrAWAL Of APPLIANcE fOr SErvIcE Or DIScONNEcTION AND bE AN ANNEALED cOPPEr PIPE.
  • Page 16 After installing the gas supply ensure that all gas controls are in the ‘Off’ position, check all connections thoroughly for leaks by turning the gas supply on and brushing a little soap and water mixture over each connection. If the mixture bubbles up there is a leak present, re-tighten the connection or replace the fittings and check it again for leaks.
  • Page 17: Servicing Instructions

    SERVICING INSTRuCTIONS NOTE: SErvIcING IS ONLY TO bE cONDUcTED bY AN AUTHOrISED AGENT. The gas controls, injectors, venturis and ignition system are accessed by removing the stainless steel hob. firstly remove the control knobs, then remove the pan supports and burner caps. remove the wok sealing ring (see diagram) by unscrewing the three stainless fixing screws.
  • Page 18 Next, the ‘A’ and ‘b’ size burner bases need to be removed. This is achieved by unscrewing the 2 x stainless fixing screws in each burner base/venturi. Lift the base and disconnect the electrode lead. The hob is further fixed via 7/10 stainless ‘acorn’ nuts which are also utilised to locate the pan supports. The nuts slide into grooves on the underside of the pan supports.
  • Page 19 GASCOCK ADJuSTMENT AND MINIMuM SETTINGS This burner is fitted with 2 x bypass screws that are accessed by removing the switch harness retaining clip and then removing the switch harness. There are two separate bypass screws – these screws are not adjustable and are supplied with specific orifices for each gas.
  • Page 20 The other 2 x valves feature a single adjustable bypass screw which can only be accessed by removing the switch harness retaining clip and thenremoving the switch harness.
  • Page 21 The outer burner (main burner) and inner burner injectors for the WOK burner can only be accessed by removing the hob from the appliance. Adjustment of the main burner venturi can be effected by loosening the fixing screw shown below. Ensure that the fixing screw is re-tightened following adjustment.
  • Page 22 PROCEDuRE FOR CONVERTING YOuR HIGHLAND COOKTOP FROM NATuRAL GAS TO uNIVERSAL LPG GAS Ensure that the correct Universal LPG test point has been fitted and that there is a ready supply of Universal LPG gas to enable you to correctly set the flames on each of the 3 burners.
  • Page 23 Next, the main (outer) burner venturi will need to be adjusted for Universal LPG. Loosen the venturi fixing screw located on the wok burner elbow - this will enable the venturi to slide in or out to achieve optimum flame. NOTE - WHEN cONvErTING TO UNIvErSAL LPG THE vENTUrI WILL NEED TO SLIDE cLOSEr TO THE INjEcTOr.
  • Page 24 Highland Appliances operate a policy of continuous improvement and reserve the right to adjust and modify its products and prices without prior notification. All Highland appliances are suitable for domestic or household use only and come with a full 2 year parts and labour warranty for your piece of mind. 0471_HI. Printed 2009.

Table of Contents