Subscribe to Our Youtube Channel
Related Manuals for Yajiang Photoelectric Equipment FREZNO 150 TW
Summary of Contents for Yajiang Photoelectric Equipment FREZNO 150 TW
- Page 1 FREZNO 150 TW USER MANUAL FREZNO 150 TW ® SS816 MODEL:SS816TW 广州市雅江光电设备有限公司 Guangzhou Yajiang Photoelectric Equipment Ltd. 电 话/Tel：020-86947788 邮箱/E-mail：sales@yajiang.cn 网址/Website：www.yajiang.cn 传真/Fax：020-86943773...
-
Page 2: Product Introduction
1 PRODUCT INTRODUCTION 1.1 SPACIFICATION SS816TW Product Code 321x363x274(mm) Dimenson 5.3KG Weight 120W Rated power Input Voltage AC100~240V Maximum Temperature 50/60Hz Ambient Temperature 0℃~45℃ Beam Angle 10°~55° Control Model DMX512/RDM 274 mm 321 mm 363 mm... -
Page 3: Safety Warning
1.2 Safety warning IMPORTANT Always read the user manual before operation. Please confirm that the power supply stated on the product is the same as the mains power supply in your area. This product must be installed by a qualified professional. •... -
Page 4: Power Connections
Safety cable HANGING UPRIGHT Important safety note!! Ÿ Always use safety cable when installing this unit!! Ÿ Be sure that the safety cable is connected to a solid load-bearing structure. Ÿ 2.2 Power connections This product uses input and output power cable is 1.5 square mm copper wire Note: If the signal cable is over 60m between the DMX512 controller and fixture or beween two fixtures, then a DMX signal amplifier is needed as well. -
Page 5: Display Panel Operation
Display panel operation 3.1 Display operation MENU/BACK FOCUS KNOB Enter DOWN KNOB 1 KNOB 2 3.2 MENU MENU KNOB MODE 1.DIMMER 2.CCT MODE 1 1.DIMMER 2.CURV MODE 2 STATIC 0-255 0-255 STROBE 0-25 ADDRESS 001-512 RUN MODE SLAVE PERSONALITY VW.D VW.F STD.P ****... - Page 6 STUDIO PERFOR MANCE POWER LIVE MCON SELF MASTER DISP KEY DISP TIME 2min **** 2700K 0-255 3000K 0-255 3200K 3400K 3600K 3800K 4000K 4200K CALR **** INFO FIXTURE HOURS VERSION LABEL...
-
Page 7: Knob Setting
3.3 KNOB SETTING MENU KNOB MODE 1.DIMMER 2.CCT MODE 1 1.DIMMER 2.CURV MODE 2 Press Enter to enter MANUAL MODE to enter the knob settings:: • MODE 1: When MODE1 is selected, DIMMER dimming brightness can be set by knob 1; CCT management can be set by rotating 2 MODE 2: When MODE2 is selected, DIMMER dimming brightness can be set by knob 1;... - Page 8 3. 7PERSONALITY PERSONALITY MENU VW.D VW.F STD.P Press enter the menu to do a custom choice on the ‘PERSONALITY’menu. • Press UP or DOWN to select UNO,DOS,VW.D,VW.F,STD.P. • Please refer to DMX channel table for the specific channel value . •...
- Page 9 SETTING : this menu allows the user to adjust key operation settings for this fixture. Ÿ RESET : RESET the lamp. Enter the password "up down up down " to confirm, and then perform the Ÿ RESET of the lamp parameters. DIMMER : tis a non-linear DIMMER speed setting “OFF”...
- Page 10 3.14 CALIB.CCT MENU **** 2700K 0-255 3000K 0-255 3200K 3400K 3600K 3800K 4000K 4200K CALR **** Enter the CALIB.CCT to select white color of different color temperature. Ÿ Press MENU button to enter the password confirmation, to enter the correct password < UP + DOWN + Ÿ...
-
Page 11: Using A Dmx512 Controller
4 Using a DMX512 Controller 4.1 Channel Assignment Note: this product have DMX512 channel configuration:UNO/DOS/VW.D/VW.F/STD.P VW.D VW.F STD.P Value Function CH.1 CH.1 CH.1 CH.1 CH.1 0-255 DIMMER CH.2 CH.2 CH.2 0-255 DIMMER FINE CH.2 CH.3 CH.3 0-255 WARM WHITE CH.4 CH.4 0-255 WARM WHITE FINE...
Need help?
Do you have a question about the FREZNO 150 TW and is the answer not in the manual?
Questions and answers