Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tews Technologies TPCE240
Summary of Contents for Tews Technologies TPCE240
- Page 1 The Embedded I/O Company TPCE240 PCI Express x1, Mini PCIe Carrier Board Version 1.0 User Manual Issue 1.0.0 February 2025 TEWS Technologies GmbH Eggerstedter Weg 14, 25421 Pinneberg, Germany Phone: +49 (0) 4101 4058 0 info@tews.com www.tews.com...
- Page 2 PCI Express x1 Carrier Board for one Mini PCIe Board TEWS Technologies GmbH has made any effort to ensure that this manual is accurate and complete. However TEWS Technologies GmbH reserves the right to change the product described in this document at any time without notice.
-
Page 3: Document History
Document History Issue Description Date 1.0.0 Initial Issue February 2025 TPCE240 User Manual Issue 1.0.0 Page 3 of 18... -
Page 4: Table Of Contents
5.5.1 x52 MPE ..........................15 5.5.2 XSR x10 ..........................16 5.5.3 BScan JTAG Connector ......................17 5.5.4 Jumper 3.3V ..........................17 5.5.5 Jumper XSR GPIO........................18 5.5.6 Jumper SMBus ........................18 TPCE240 User Manual Issue 1.0.0 Page 4 of 18... - Page 5 FIGURE 5-2 : +3.3V SELECTION DIAGRAM ....................11 FIGURE 5-3 : +3.3V JUMPER CONFIGURATION (J3) .................. 11 FIGURE 5-4 : LED OVERVIEW ........................12 FIGURE 5-5 : CONNECTOR OVERVIEW ...................... 13 TPCE240 User Manual Issue 1.0.0 Page 5 of 18...
- Page 6 TABLE 5-12 : JUMPER XSR GPIO ......................... 18 TABLE 5-13 : JUMPER XSR GPIO PIN ASSIGNMENT ................. 18 TABLE 5-14 : JUMPER SMBUS ........................18 TABLE 5-15 : JUMPER SMBUS PIN ASSIGNMENT ..................18 TPCE240 User Manual Issue 1.0.0 Page 6 of 18...
-
Page 7: Product Description
1 Product Description The TPCE240 is a PCI Express Revision 2.0 compatible carrier board for one PCIe Mini Card. While specifically designed to run, test and maintain TEWS Mini PCI Express modules, it is an ideal solution for prototyping, but it can also be used to build modular, flexible and cost effective I/O solutions for all kinds of applications like process control, medical systems, telecommunication and traffic control. -
Page 8: Technical Specification
If FIT rates are not available, MIL-HDBK-217F and MIL-HDBK-217F Notice 2 formulas are used for FIT rate calculation. Humidity 5 – 95 % non-condensing Weight 61.5 g Table 2-1 : Technical Specification TPCE240 User Manual Issue 1.0.0 Page 8 of 18... -
Page 9: Handling And Operation Instructions
3 Handling and Operation Instructions ESD Protection The TPCE240 is sensitive to static electricity. Packing, unpacking and all other handling of the TPCE240 has to be done in an ESD/EOS protected Area. 4 Terms and Definitions Style Conventions "Active Low" signals are shown with a # suffix (i.e. RESET#). -
Page 10: Configuration Hints
J1: The GPIO Pins of the debug interface are connected to a pin header for various use cases, for example indicating “PGOOD” and “FPGA done” or using it as a communication interface (UART). J2: to connect the SMBus TPCE240 User Manual Issue 1.0.0 Page 10 of 18... -
Page 11: Figure 5-2 : +3.3V Selection Diagram
Pin 1, 4 or 5 and GND to Pin 9 or 10. Make sure to use only one out of four possibilities, otherwise it may cause damage to the board or peripherals. Figure 5-3 : +3.3V Jumper Configuration (J3) J4: possibility to connect a fan for additional cooling TPCE240 User Manual Issue 1.0.0 Page 11 of 18... -
Page 12: Figure 5-4 : Led Overview
Mini PCIe WPAN Indication Green GPIO1 XSR Connector Indication Green GPIO0 XSR Connector Indication Green 3.3V and 1.5V Supply are ok Green Supplies are not OK Table 5-2 : LED Description TPCE240 User Manual Issue 1.0.0 Page 12 of 18... -
Page 13: Figure 5-5 : Connector Overview
Connector Overview X5/X6 Figure 5-5 : Connector Overview TPCE240 User Manual Issue 1.0.0 Page 13 of 18... -
Page 14: Pin Assignment
Direction and detailed signal descriptions depends on which Mini PCIe module is mounted on the carrier board. The MDR50 pinout is the same as the PicoClasp(X2) pinout of the mounted MPE module. TPCE240 User Manual Issue 1.0.0 Page 14 of 18... -
Page 15: Onboard Connectors
3.3V Jumper PERp0 direct via 0R to GND W_DISABLE2# 3.3V Jumper 3.3V Table 5-6 : x52 MPE Pin Assignment default pinout in brackets, red mark is used connected to PCIe Slot TPCE240 User Manual Issue 1.0.0 Page 15 of 18... -
Page 16: Xsr X10
SM10B-XSRS-ETB or compatible Table 5-7 : XSR x10 5.5.2.1 Pin Assignment Description (Test Data to MPE Card) (Test Data from MPE Card) GPIO0 GPIO1 PRESENT1# Table 5-8 : XSR x10 Pin Assignment TPCE240 User Manual Issue 1.0.0 Page 16 of 18... -
Page 17: Bscan Jtag Connector
5.5.4.1 Pin Assignment Description Description n.c. n.c. 3.3V Regulator 3.3V x52 Connector 3.3V x52 Connector 3.3Vaux PCIe Slot 3.3V PCIe Slot 3.3V x52 Connector Table 5-11 : Jumper 3.3V Pin Assignment TPCE240 User Manual Issue 1.0.0 Page 17 of 18... -
Page 18: Jumper Xsr Gpio
TSW-102-07-S-D-LL, Samtec or compatible Table 5-14 : Jumper SMBus 5.5.6.1 Pin Assignment Description Description SMB_DATA Mini PCIe SMDAT PCIe Slot SMB_CLK Mini PCIe SMCLK PCIe Slot Table 5-15 : Jumper SMBus Pin Assignment TPCE240 User Manual Issue 1.0.0 Page 18 of 18...
Need help?
Do you have a question about the TPCE240 and is the answer not in the manual?
Questions and answers