1.7 Connecting Peripheral Devices ......................3 1.8 Turning on monitors and servers ......................3 2.Description of the System Architecture ......................4 2.1 TS1610 structural characteristics ......................4 3 System description and setup .........................7 3.1 CPU ..............................7 3.2 Memory ............................... 8 3.3 Video Controller ...........................
TS1610 USER MANUAL 1.Preparation for use 1.1 Summary The main task of this chapter is to describe how to do some basic preparations. They include: Check the transportation packaging; Choose a suitable location to place the server; Check the power setting switch;...
TS1610 USER MANUAL The server can work reliably in a normal office environment. Select an environment that meets the following conditions: Satisfying specialized Clean and low dust Well-ventilated and away from heat sources environmental Keep away from environments where vibrations or physical impacts...
TS1610 USER MANUAL Power cord required Descriptive speed The wir es sho ul d be ra te d to ca rry an AC curr ent of 125% of the amount of current req ui re d by the se rve r .
If a fault occurs, record the error message displayed on the screen and the audible code heard, see chapter: System Troubleshooting 2.Description of the System Architecture 2.1 TS1610 structural characteristics Front Schematic: Figure 2-1 Front View of the TS1610 Server Front Panel Schematic...
Page 7
TS1610 USER MANUAL Figure 2-2 TS1610 Server Front Panel Diagram 1:on/off key 2:power status light 3:hard disk status light 4:network 1 indicator (not supported) 5:network 2 indicator (not supported) 6:system alarm light 7:restart key 8:fault alarm mute...
Page 8
TS1610 USER MANUAL System indicator: Name (of a thing) Color State of affairs Clarification Power Indicator resounding The power supply is energized greener Hard Disk Indicator orange resounding Hard Disk In-Place Status (color) Network 1 indicator greener resounding The network connection is working.
TS1610 USER MANUAL 3 System description and setup 3.1 CPU 3.1.1 CPU Overview Supports one Intel® L G A 1151 Intel® Xeon E system The cpu is a full line cpu, supporting up to 95w, and supports both 32-bit and 64-bit operating systems.
TS1610 USER MANUAL 3.2 Memory 3.2.1 Memory Overview The server has 4 memory slots, expandable up to 128G; supports up to DDR4 2666MT/s Registered/ECC/unbuffered memory. 3.2.2 Memory Installation Precautions 1. Pull the retaining clips for the memory slots outward. 2. When a memory module is inserted into a memory slot, the notched side of the memory module aligns with the tabs of the memory module slot.
TS1610 USER MANUAL Number of memory sticks memory location Position 1/2/3/4 3.3 Video Controller Motherboard Integrated ASPEED2500 Video Controller 3.4 Hard disk controllers Supports 6 SATA3 hard drives. 3.5 Network Controller Two integrated dual-channel Gigabit LAN cards (Intel® I350 chips) provide high-speed network connectivity.
TS1610 USER MANUAL Red Hat Enterprise Linux* 7U0 64bit Red Hat Enterprise Linux* 7U1 64bit Red Hat Enterprise Linux* 7U2 64bit Red Hat Enterprise Linux* 7U3 64bit Red Hat Enterprise Linux* 7U4 64bit 4. Integrated RAID Configuration This chapter describes the use of motherboard integrated SATA RAID controller to create RAID1, RAID0 and RAID10, RAID1 after the creation of the hard disk capacity is only half of the total capacity, the hard disk to form a backup, the reliability of a lot of improvement.
Page 13
TS1610 USER MANUAL 4.2.2 To create an array, select the Create RAID Volume option and the following menu appears:...
Page 14
TS1610 USER MANUAL Press < ↑>,< ↓> to move the cursor up and down, and select the level of array you want to create at RAID Level, the options are RAID0, RAID1 and RAID5. After selecting the array level and the hard disks to be arrayed, tap Create Volume Options Select 'Y' as prompted to create the array.
TS1610 USER MANUAL 4.2.4 Enter and select the array you want to delete, then press 'DEL' and select 'Y' to delete the array as shown below: 5.Operating system installation instructions This chapter describes the manual installation of the windwos server 2016 operating system and driver installation.
Page 16
TS1610 USER MANUAL 2. If you are using an integrated RAID drive, insert the supplied driver CD-ROM into this computer, the CD- ROM will run automatically and the driver navigation screen will appear. 3. Select the "Driver" option on the navigation interface, enter the Driver interface, select the model where the operating system server needs to be installed, and then select the operating system that needs to be installed.
Page 17
TS1610 USER MANUAL Select "Install now" when the image below appears. You need to select "Delete" to delete all partitions before installing the new system, press "Next".
TS1610 USER MANUAL Select "Datacenter Evaluation (Desktop experience)", press "Next" to install windows.After the installation, you have to install the driver, copy the driver to the USB flash drive, then install Chipset, follow the prompts until the driver is installed, as shown in the following figure.
Page 21
TS1610 USER MANUAL 3. Go to the following screen and click Next...
Page 22
TS1610 USER MANUAL 4. The system enters the following screen, click Next 5. Select the system language, the default English, click Next, see the following figure...
Page 23
TS1610 USER MANUAL 6. Select the keyboard type, default, click Next, see the figure below. 7. Select the device type, default, click Next, see the figure below.
Page 24
TS1610 USER MANUAL 8. Select the time zone, select Chongqing, the following figure 9. Set the Root user password, click Next after setting, see the figure below.
Page 25
TS1610 USER MANUAL 10. Click on the Use Anyway box, see below. 11. Select the type of installation, mainly on the disk operation, select the custom system partition, you can choose the last item see below (if you need to install on the array card, the driver installation method refer...
Page 26
TS1610 USER MANUAL 12. Tap Next by default, as shown below. (You can also choose the last item to manually divide according to the actual demand) 13. Click the Format button in the prompt box, see below.
Page 27
TS1610 USER MANUAL 14. Click the prompt box Write change to disk 15. Click Next for the default selection, see the figure below.
Page 28
TS1610 USER MANUAL 16. Select the type of system to be installed, here choose the desktop version, see the following figure (or you can choose the installation package according to the demand) 17. System installation is in progress, wait for it, see the following figure...
Page 29
TS1610 USER MANUAL 18. After the installation is complete, click Reboot, see the figure below. 19. Click Forward on the Welcome page, see below.
Page 30
TS1610 USER MANUAL 20. Click Forward by default, see below. 21. Click Forward by default, see below.
Page 31
TS1610 USER MANUAL 22. Click Forward by default, see below. 23. Creating a user name and password Forward, see below...
Page 32
TS1610 USER MANUAL 24. To set the time and date, click 25. Setting is complete, click Finish, enter the system, see the following figure...
TS1610 USER MANUAL 26. Enter the user name / password, enter the system, so the system installation is complete, see the following figure 6. System Troubleshooting 6.1 Introduction to System Reset This chapter helps you to check and solve problems that you may encounter while using the Bauder Server system.
TS1610 USER MANUAL 6.2 Initial system startup Problems with the first boot of a system are usually caused by incorrect installation or configuration. Failures directly attributable to hardware are relatively rare. Check the steps: . Are all cables properly connected and wired securely.
TS1610 USER MANUAL ast to at least two-thirds of their maximum values (see the documentation that came with the monitor). 4. Turn on the system. If the power indicator does not light up, see the troubleshooting description below for the power indicator does not light up.
Page 36
TS1610 USER MANUAL 6.4.3 Incorrect or distorted characters displayed on the screen Please check the following: - The brightness and contrast of the monitor are adjusted appropriately. See the monitor manufacturer's documentation. - The signal line power cable of the monitor is installed correctly.
Page 37
TS1610 USER MANUAL - The CD-ROM is configured correctly. - Whether the motherboard's integrated IDE controller has been enabled. Attention: IDE and SATA Devices Indicated by Front Panel Lights: The Hard Disk Drive Activity light on the front panel illuminates when an IDE hard disk or a SATA device controlled by the motherboard's integrated SATA controller is in use.
Need help?
Do you have a question about the TS1610 and is the answer not in the manual?
Questions and answers