Advertisement
30106368GB.fm Page 2 Friday, April 2, 2010 5:44 PM
CONSUMPTION DATA
Temperature
Programme
(°C)
Cotton
95
Cotton
60
Cotton with "Eco"**
60
Cotton
40
SuperEco
60
Synthetics
60
Synthetics
40
Delicates
30
Daily load
40
Quick wash
30
Wool
40
Handwash
40
Lingerie
30
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
**
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
Add detergent as indicated on the front page and as
described in your Instructions for Use.
Close the door and turn the programme selector to the
desired programme and temperature. The indication lamp
next to the "Start (Pause)" button blinks.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
"Prewash" button
• Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when
activating the "Prewash" option.
"Eco" button
• With a modified temperature profile and a prolonged
wash duration, the optimum combination of good wash
result and lower energy consumption is achieved.
Black process 45.0° 150.0 LPI
Load
Water
Energy
Approx. Programme Duration
(kg)
(l)
(kWh)
(hours : minutes)
6.0
59*
1.90
2:00
6.0
49
1.02
2:20
6.0
49
0.78
4:00
5.0
56
0.70
2:00
6.0
51
0.72
4:00
2.5
50*
0.80
1:35
2.5
46
0.50
1:20
1.5
60
0.50
0:45
3.0
41
0.50
1:00
3.0
41
0.40
0:30
1.0
60
0.50
0:45
1.0
45
0.50
0:40
1.0
45
0.40
0:36
"Intensive rinse" button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
"Easy ironing" button
• Reduces creasing by an increased water quantity and a
very gentle spin.
"Variable spin" button
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If spin speed "0" is selected, the final spinning is
cancelled but intermediate spin peaks remain during
rinse. The water is drained out only.
START DELAY
The "Start delay" allows to run the machine at the
consumer's convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the start delay.
• Select programme, temperature and options.
• Press the "Start delay" button to select the delay time
by 1, 3, 6, 9 or 12 hours.
• Press the "Start (Pause)" button.
The "Start delay" indication blinks and the countdown
of the delay time begins.
• When the programme starts, the start delay indicator
light goes off and is replaced by the programme
sequence indication.
• After the "Start (Pause)" button has been pressed,
the number of hours preselected can be reduced by
pressing again the "Start delay" button.
To cancel the "Start delay"
...before you press the "Start (Pause)" button:
• Turn the programme selector to another position or
press the "Reset" button.
...after having pressed the "Start (Pause)" button:
• Press the "Reset" button for at least 3 seconds - the
start delay indicator light goes off.
PROGRAMME START
Open the tap and press the "Start (Pause)" button. The
indication lamp next to the "Start (Pause)" button lights
up. The programme sequence indicator shows the current
programme phase, running from left to right through
Wash, Rinse, Spin/Drain.
• When the programme phase is finished, the
corresponding indication goes off.
"DOOR OPEN" INDICATION
Before starting and after end of a programme, the lamp
lights to show that the door can be opened. As long as a
wash programme is running, the door remains locked and
must on no account be forced open. In case you have an
urgent need to open it during a running programme, refer
to "Reset a running programme before the end".
RED INDICATIONS
"Service"
Lighting up of the "Service" indication can be caused by a
fault in an electrical component. Refer to the
"Troubleshooting Guide" in your Instructions for Use; if
the fault persists, contact our After Sales Service.
"Water tap closed"
The appliance has no or insufficient water supply. Open
the water tap; if the indication still lights up, refer to the
"Troubleshooting Guide" in the Instructions for Use.
"Clean pump"
Waste water is not pumped out. Check whether the drain
hose is kinked or the filter must be cleaned; in the latter case
refer to the Instructions for Use ("Removing the Filter").
PROGRAMME END
•
All the lights of the programme sequence indicator
are off, and the "Door open" indication lights up.
1. Turn the programme selector to the "Off/O" position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the "Start (Pause)" button to pause the
programme. The light blinks.
2. Select the new programme (with temperature), any
options and another spin speed if you want.
3. Press the "Start (Pause)" button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
RESET A RUNNING PROGRAMME BEFORE
THE END
The "Reset" button cancels a programme before the end.
•
Press the "Reset" button for at least 3 seconds. The
water is drained out; it may last a while until the door
can be opened.
Whirlpool is a registered trademark of Whirlpool USA
5019 301 06368
Advertisement
