Advertisement
Product dimensions
29-7/32"
cooktop
recessed width
28-5/32" oven
recessed width
30-3/4"
recessed height
from underside
of cooktop to
support slats
shipping
23-1/8"
recessed
depth
Cabinet opening dimensions
Countertop preparation:
Front edges: You may need to
shave or cut the trim of formed
or metal front-edged
countertops to clear the 30"
width of cooktop.
13" max. upper
cabinet depth
For minimum
clearances to the
top of cooktop see
Note.*
wall
1-1/8"
20-5/16"
max.
25" countertop
depth
24" lower
cabinet
cabinet depth
front
floor
Side view of
cabinet cutout
*Note: 24" min. when bottom of wood or
metal cabinet is protected by not less than
1/4" flame retardant millboard covered
with not less than No. 28 MSG sheet steel,
0.015" stainless steel, 0.024" aluminum or
0.020" copper.
30" min. clearance between the top of the
cooking platform and the bottom of an
unprotected wood or metal cabinet.
Page 1
30"
cooktop
width
foot
30"
overall width
If countertop thickness is
more than 1-1/2" inches
thick: Countertop must be
notched as shown to avoid
damaging the oven control
panel.
notch width
to be equal
both sides
1-1/2"
max
30-1/8"
1-1/2" max.
countertop
thickness
Top of countertop
28-1/2" min.
must be level
opening width
across front and
front to back.
Locate electrical
supply junction
box on cutout
floor or on rear
wall (shown)
near floor line.
Front view of
cabinet cutout
24-13/32"
to back
of oven
21-7/8"
cooktop depth
31-3/8"
overall
height
If countertop extends more
1-1/8" beyond cabinet front:
Notch countertop as shown
to clear oven control panel.
cabinet
front
notch width
to be equal
both sides
1-1/8"
max
30-1/8"
Top view of
cabinet cutout
1/4"
radius
both corners
30-3/4"
top of
countertop to
support slats
Install a 3-1/2"-wide
support slat on each
side. Slats must be level
front to back and with
each other.
29-3/8"
7/8" difference
between 29-3/8"
dim. and 28-1/2"
opening width
equally spaced
both sides.
7/8" min.
30-3/4"
required
top of
between
36" overall
counter-
cutout and
countertop
top to
cabinet door
height
bottom
or hinge.
of cabinet
cutout
Before you start...
Your safety and the safety of others are
very important.
We have provided many important safety messages in this
manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill
or hurt you and others.
All safety messages will follow the safety alert symbol and
either the word "DANGER" or "WARNING". These words mean:
DANGER
You can be killed or seriously injured if you don't
immediately follow instructions.
WARNING
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is,
tell you how to reduce the chance of injury, and tell you what
can happen if the instructions are not followed.
Important: Observe all governing codes and
ordinances.
Proper installation is your responsibility. Have a qualified
technician install this range.
Range location should be away from strong draft areas,
such as windows, doors and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
Recessed installation area must provide complete enclosure
around the recessed portion of the range.
Electrical ground is required. See "Electrical requirements. "
IMPORTANT: Some cabinet and building materials are not
designed to withstand the heat produced by the oven for
baking and self-cleaning. Check with your builder or cabinet
supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.
Range support surface MUST be solid, level and flush with
bottom of cabinet cutout.
Do not seal range to side cabinets.
When installing a cooktop under existing cabinets and the
installation does not meet the minimum cabinet clearances,
install a range hood above the cooktop to avoid burn
hazards.
It is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA
70 — latest edition**, and all local codes and ordinances.
Mobile home installation
The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR, Part 3280 (formerly the Federal Standard for
Mobile Home Construction and Safety, Title 24, HUD, Part
280); or when such standard is not applicable, the Standard
for Manufactured Homes Installations (Manufactured Home
Sites, Communities and Setups), ANSI A225.1/NFPA 501A,
or with local codes.**
When this range is installed in mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.
Four-wire power supply cable must be used in a mobile
home installation. The appliance wiring will need to be
revised. See four-wire electrical connection, Page 3.
Copies of the standards listed may be obtained from:
** National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Tools needed:
1/2" dia.
Phillips
router bit
screwdriver
Parts supplied:
2 screws
Advertisement
