1. Manuals
  2. Brands
  3. U.S.SAWS Manuals
  4. Industrial Equipment
  5. PC3000
  6. Operating manual

U.S.SAWS PC3000 Operating Manual

Tamping rammer
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PC3000 TAMPING RAMMER
OPERATING MANUAL
Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any
Notice of Copyright Protection
means without the prior written permission of U.S.SAWS
Waterworks
Division
P: 866- 987-7297 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
U.S. English
11-19-2024

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PC3000 and is the answer not in the manual?

Questions and answers

Related Manuals for U.S.SAWS PC3000

Summary of Contents for U.S.SAWS PC3000

  • Page 1 PC3000 TAMPING RAMMER OPERATING MANUAL Notice of Copyright Protection Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any means without the prior written permission of U.S.SAWS 11-19-2024...

  • Page 2: Introduction And Specifications

    & maintenance Starting System Recoil of the PC3000 & to instruct you in safety practices for dealing with these conditions. Keep all manuals provided with your machine in a safe place at Jumping Stroke 2.8”...

  • Page 3: Symbols And Decals

    You must be qualified for safe operation of the U.S.SAWS PC3000 machine. You must clearly understand the written instructions supplied by U.S.SAWS, be trained - including actual operation - & know the safety rules & regulations for the job site. It is a safety practice to point out & ex- plain safety signs &...

  • Page 4: Safety Instructions

    Keep children and visitors away Do not operate this machine unless you have received operational and from the work area. maintenance training from a U.S.SAWS representative or from an autho- rized distributor for U.S.SAWS. 4.12 KEEP FIRM GRIP ON MACHINE.

  • Page 5: Dust Warning

    S A F E T Y I N S T R U C T I O N S 4.20 DO NOT USE DRUGS, ALCOHOL, MEDICATION. Do not operate machine while under the influence of drugs, alcohol, or any medication. 4.21 KEEP THE RIGHT PARTS IN THE RIGHT POSITIONS.

  • Page 6: Pre-Operation Checklist

    • Never run the Engine with low or no engine oil. Start by reading the entire PC3000 operations and maintenance • Running the Engine with low or no engine oil WILL permanently damage manual. Get familiar with the machine’s parts.
  • Page 7 O P E R AT I O N C H E C K L I S T OPERATOR QUALIFICATIONS Preventing Burns • Never touch the muffler, muffler cover or engine body while engine is Carefully read and understand this entire manual before operating machine.
  • Page 8 O P E R AT I O N C H E C K L I S T Below is a diagram that gives a general introduction to the machine parts. Figure A shows all the essential parts that the user must be familiar with before operating the rammer.
  • Page 9 O P E R AT I O N C H E C K L I S T B. Check the engine oil regularly before starting the engine. Move the STARTING engine to a vertical position and check the oil level from the oil level gauge To start the rammer, follow the procedure below.

  • Page 10: Maintenance And Service

    O P E R AT I O N C H E C K L I S T OPERATING Follow the steps below while operating the rammer. Wear gloves while operating machine to reduce fatigue caused by vibra- 1. Move the throttle lever quickly from IDLE to OPERATING position to start tion.

  • Page 11: Maintenance

    M A I N T E N A N C E MAINTENANCE Table 2: Service Chart DAILY • Remove oil and dirt thoroughly from the engine and control area. • Clean or replace air filter as necessary. • Check and retighten all fasteners as necessary. •...

  • Page 12: Troubleshooting

    T R A N S P O R TAT I O N, S TO R A G E & T R O U B L E S H O O T I N G TRANSPORTATION TROUBLESHOOTING Transport rammer in the upright position. If machine must be laid down for transportation, fuel tank must be drained.

  • Page 13: Warranty And Service

    Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form.
  • Page 14 FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S.SAWS, 8004B E. Broadway Ave. Tampa, FL 33619, Fax No. 714-434-7299...

Table of Contents