Table of Contents
Advertisement
Quick Links
U.S.SAWS HEAVY DUTY DUST
BUGGY OPERATING MANUAL
Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any
Notice of Copyright Protection
means without the prior written permission of U.S.SAWS
Surface Prep
Division
P: 877-817- 6687 F: 813-621-7125
Visit us at www.ussaws.com
sales@ussaws.com
U.S. English
04-06-2022
Advertisement
Table of Contents
Related Manuals for U.S.SAWS Heavy Duty Dust Buggy
Summary of Contents for U.S.SAWS Heavy Duty Dust Buggy
- Page 1 U.S.SAWS HEAVY DUTY DUST BUGGY OPERATING MANUAL Notice of Copyright Protection Copyright 2020, by U.S.SAWS . All rights reserved. This work may not be reproduced or disseminated in whole or in part by any means without the prior written permission of U.S.SAWS 04-06-2022...
-
Page 2: Introduction And Specifications
The owner’s manual is intended to point out some of the basic safety situa- tions that maybe encountered during the normal operation & maintenance SPECIFICATIONS of the U.S.SAWS Heavy Duty Dust Buggy Machine & to instruct you in safety practices for dealing with these conditions. Keep all manuals provided with Model Heavy Duty Dust Buggy your machine in a safe place at all times. -
Page 3: Symbols And Decals
Buggy walk behind machine. You must clearly understand the written instructions supplied by U.S.SAWS, be trained - including actual operation - & know the safety rules & regulations for the job site. It is a safety prac- tice to point out & explain safety signs & practices to others & to make Wear appropriate clothing sure they understand the importance of following these instructions. -
Page 4: Safety Instructions
Do not touch the muffler while it is hot. Let the engine cool maintenance training from a U.S. SAWS representative or from an autho- before storing indoors. Do not place flammable objects close to the engine. rized distributor for U.S.SAWS. 4.15 AVOID CONTACT WITH HOT BLADE AND BLADE GUARD. -
Page 5: Dust Warning
S A F E T Y I N S T R U C T I O N S 4.24 STORE IDLE EQUIPMENT. 4.38 NEVER DISABLE THE LEVER. The machine, blades and tools should be stored in a dry and secure loca- Do not modify, disable, or attempt to permanently engage the lever. -
Page 6: Pre-Operation Check List
WARNING: Improperly maintaining the Heavy Duty Dust Buggy CAUTION: Running the Heavy Duty Dust Buggy generates heat in the including the Metabo grinder or failing to correct a problem before engine, blade and blade guard. Do not touch these components with- operation could cause a malfunction resulting in a serious injury. - Page 7 WARNING: If you can see the drive belt or diamond blade, the See Figure 10. guards are not in place. Never operate a Heavy Duty Dust Buggy without guards in place. The proper position for the belt guard is bolted with four bolts to the chassis.
- Page 8 WARNING: Recommended accessories for this tool including blades are listed in this manual or are available by calling customer service. The use of any other attachment or accessory might be hazardous 5.11 Heavy Duty Dust Buggy premium dry cut diamond blades, medium bond JOINT WIDTH (INCHES) DEPTH OF...
-
Page 9: Operation
The blade will turn as soon as the Heavy Duty Dust Buggy is turned on. Figure 6 - Heavy Duty Dust Buggy SAWS blade depth setting WARNING: Never attempt to start the machine with the diamond blade inserted in a joint or previous cut. -
Page 10: Operating The Saw
O P E R AT I O N LINING UP THE BLADE WITH THE JOINT/POINTER ADJUSTMENT 6.22 Align bolt holes for Dust Buggy Arm in the most vertical position. Open Joint: With an un-filled control joint where it only needs to 6.16 Make sure the Adjustment Lever is in position. -
Page 11: Parts Breakdown
PA R T S B R E A K D O W N Heavy Duty Dust Buggy Parts Breakdown P: 877-817- 6687 F: 813-621-7125 Surface Prep Visit us at www.ussaws.com Division sales@ussaws.com... - Page 12 PA R T S B R E A K D O W N P: 877-817- 6687 F: 813-621-7125 Surface Prep Visit us at www.ussaws.com Division sales@ussaws.com...
- Page 13 PA R T S B R E A K D O W N P: 877-817- 6687 F: 813-621-7125 Surface Prep Visit us at www.ussaws.com Division sales@ussaws.com...
- Page 14 A S S E M B LY ASSEMBLY Install handle as shown The Dust Buggy handle comes pre-assembled and simply needs to be bolted to the rolling chassis. 8.3.1 Begin with bolting the main handle to the chassis. Make sure to place the supplied bent handle washer opposite to the chassis as shown.
-
Page 15: Blade Installation And Removal
A S S E M B LY BLADE INSTALLATION AND REMOVAL 8.4.1 The door on the side of the Dust Buggy locks the 8.4.3 The Dust Buggy is supplied with two (2) large blade “shoe” into position and provides access to the blade nut. flanges. -
Page 16: Related Products
R E L AT E D P R O D U C T S General Joint Cleanout / Concrete Cutting DCB08095UD 8 X .095 X 5/8-7/8 Supreme Grade Dry Cut Blade DCB08125UD 8 X .125 X 5/8-7/8 Supreme Grade Dry Cut Blade DCB08250UD 8 X .250 X 5/8-7/8 Supreme Grade Dry Cut Blade Polyurea / Joint Filler Removal APB08095D 8 X .095 X 5/8-7/8 TIGERTOOTH Diamond Grit Blade... -
Page 17: Warranty And Service
Warranty This document is to be used as a guide in determining warranty policies and procedures for U.S.SAWS and its U.S.SAWS products. It is to be used in determining whether a warranty is justified and as a procedural guide in completing a U.S.SAWS warranty claim form. - Page 18 FILL OUT THE ATTACHED CARD COMPLETELY AND ACCURATELY. WARRANTY REGISTRATION CARD IMPORTANT! To ensure that your U.S.SAWS machine is covered under warranty, please fill in the following information and mail or fax it to U.S. SAWS, 8004B E. Broadway Ave. Tampa, FL 33619, Fax No. (813) 621-7125...
Need help?
Do you have a question about the Heavy Duty Dust Buggy and is the answer not in the manual?
Questions and answers