Summary of Contents for Morphy Richards IB29100
- Page 1 Flat panel micro system with cd player and built in subwoofer 29100 OPERATING INSTRUCTIONS...
- Page 2 Illustration...
-
Page 3: Display Illustration
Display illustration Play / Pause 17 Connector Cable Stop / Band (MW / FM) button 18 Connector Socket CD Repeat / Memory button 19 Main Switch Tuning / Skip / Search Up button 20 Left Aux terminals Tuning / Skip / Search Down button 21 Right Aux terminals Remote sensor 22 AC Input... -
Page 4: Cd Display Window
CD display window A Track number indicator B Band indicator C Track / time indicator D Stereo indicator... -
Page 5: Electrical Requirements
Electrical requirements Check the voltage on the rating plate of your CD microsystem corresponds with your house electricity supply which must be A.C. (alternating current). If the socket outlets in your home are not suitable for the plug supplied with this appliance the plug should be removed and the appropriate one fitted. - Page 6 Installing the ribbon cable to the amplifier terminals Connect the ribbon cable between the CD and Amplifier units as shown below. Installing the speaker wire to the speaker terminals Connect the speaker wires to the right and left speaker terminals as shown below.
-
Page 7: Clock Setting
Operating the unit (Power/standby) When you first plug the unit into the AC outlet, the unit will be in STANDBY mode. Ensure that the main switch on the rear is switched to on. You can press the POWER button on the unit (or on the remote control) to switch the unit ON and OFF. -
Page 8: Radio Operation
The unit will turn off automatically after 1 hour. Press the STANDBY / ON button to turn off before the set time. Press and hold the TIMER button to completely cancel the timer function. Radio operation Ensure unit is not in standby mode. Press the TUNER button to select the Radio operation. - Page 9 Notes: Storing a new station into a preset location will erase the previously stored station in that location. Power off / failure or power cord disconnection will clear the memory of all preset stations. Perform the station presetting procedures again to store the stations. Selecting the preset stations Press the STOP / BAND (MW / FM) button to select the desired band.
-
Page 10: Selecting A Different Track
To interrupt playback, press PLAY / PAUSE. The time elapse indicator will flash. To resume playback, press PLAY / PAUSE again. To stop playback, press STOP. Selecting a different track Press SKIP UP / DOWN button on the unit (or remote), until the required track number appears in the display. -
Page 11: Playing A Program
Intro play (for remote handset) Press the INTRO button once, and the "INTRO" indicator will light up. Shortly after this, every track will be played for only 10 seconds from the beginning. Programming By programming the CD player, you can play up to 20 tracks in any desired order. (possible only when the CD is in stop mode.) Place the disc to be programmed in the tray. -
Page 12: Reset Function
Mute play (for remote handset) If you press the MUTE button, mute will appear on the display & the audio output will be temporarily muted. Press MUTE button again, the indicator will go out and the audio output will continue as normal. Aux play Press the AUX button once and the "AUX"... -
Page 13: Compact Disc
Compact disc Always use compact discs bearing the mark as shown. Notes on handling discs: When removing the disc from its storage case and loading it. Do not touch the reflective recorded surface. Do not stick paper or write anything on the surface. Do not bend the disc. -
Page 14: Warning Labels
Warning labels WARNING: to reduce the risk of an electric shock, do not expose this appliance to rain or moisture. ATTENTION: To reduce the risk of an electric shock, do not remove the cover. There are no user serviceable parts inside the unit. Refer any servicing to qualified personnel. -
Page 15: Technical Specification
Technical specification AC Power supply 230V 50Hz Out put power 5 watts RMS x 2 Subwoofer power 20 watts CD player Frequency response 100Hz to 16kHz Optical pickup 3 beam laser Radio FM 87.5MHz - 108MHz MW 522KHz - 1620KHz WARNING : This unit uses a laser beam. - Page 16 Guarantee Morphy Richards products are manufactured to internationally accepted quality standards. In addition to your statutory rights, Morphy Richards guarantee your product to be free from manufacturing and component defects for a period of TWO YEARS from date of purchase.