Download Print this page

BN Thermic SystemX XD-60 Instructions

Fan assisted heater

Advertisement

Quick Links

Thank you for purchasing a BN Thermic product. Manufactured to a high standard, this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance. Please ensure instructions remain with your
customer for their reference.
REGISTER: PLEASE REGISTER THIS PRODUCT ONLINE TO ACTIVATE YOUR GUARANTEE AT
AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAF E TY I N ST RU CT IO N S
1.1 ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs,
sockets and any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the
installation of appropriate safety devices. A Residual Current Circuit Breaker (RCCB) should be incorporated in the main
distribution board. If in any doubt consult a qualified electrician.
You must also read and understand the following instructions concerning electrical safety.
The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those
appliances and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
Installation should always be carried
out by a qualified electrician or a
competent person in accordance with
current electrical regulation.
Ensure that the insulation of all the
cables
on
the
undamaged
and
connecting it to the power supply.
Ensure that the cables are always
protected against short circuit and
overload.
Regularly inspect the power supply cables and plugs etc. for wear or damage and check all connections to ensure that none
are loose.
Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that a correctly rated
fuse is fitted.
DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a
qualified electrician.
The unit should be protected by a suitably rated isolator and fuse or MCB.
This heater is IP20 rated and is suitable for indoor or under cover use only.
Do not attach this heater to an extension cord it must be hard wired in position.
1.2 GENERAL SAFETY INSTRUCTIONS
Remove all packaging and store it away from children, check the package and heater for visible damage or tampering.
Familiarise yourself with the applications and limitations of the heater.
Ensure the heater is in good order and condition both physically and electrically before use. If in any doubt, do not use the
unit and contact your supplier.
Only use recommended attachments and parts. To use unauthorised parts may be dangerous and will invalidate your
warranty.
Keep tools and other items away from the heater when it is in use.
Keep children and unauthorised persons away from the heater, as it gets hot.
Disconnect from mains and allow to cool before attempting any cleaning or maintenance.
X DO NOT use in areas where hazardous gases or dusts that may be present.
X DO NOT locate the heater directly below the power outlet.
X DO NOT disassemble the heater for any reason. This heater must be checked by qualified personnel only.
X DO NOT use this heater to perform a task for which it has not been designed.
WARNING! This heater is not equipped with a built in device to control the room temperature. Do not use this heater in a
small room if it is occupied by people not capable of leaving the room on their own, unless constant supervision is provided.
WARNING! Ensure you observe the safety distances and mounting heights and there is no possibility of inflammable
materials coming into contact.
PLEASE READ THESE INSTRUCTIONS, NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS,
appliance
is
safe,
before
FAN ASSISTED HEATER
Model:- XD-60
www.
.co.uk
bnthermic
INSTRUCTIONS FOR:-

Advertisement

loading
Need help?

Need help?

Do you have a question about the SystemX XD-60 and is the answer not in the manual?

Questions and answers

Summary of Contents for BN Thermic SystemX XD-60

  • Page 1 Model:- XD-60 Thank you for purchasing a BN Thermic product. Manufactured to a high standard, this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. Please ensure instructions remain with your customer for their reference.
  • Page 2 2. I NTR O D UCT IO N & S P EC IF IC ATIO N This heater produces a totally dry heat, no condensation, no gas, no fumes. It reaches maximum heat output within a minute from being turned on. It is quick and easy to install reducing installation costs. Used with the CX range of controllers it provides low / high heat or fan only settings.
  • Page 3 4.3 CEILING MOUNTING ABOVE A DOORWAY You can either use M8 drop rods in the two threaded holes in the top of the heater (drop rods not supplied) or mount directly to the ceiling using the supplied brackets. If mounting using the supplied brackets use the method (section 4.2) above with the exception that you use the Large Side Brackets and they must face upwards (see Pic5).
  • Page 4 IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Your BN Thermic product is guaranteed for one year from date of BN Thermic Ltd, purchase. We will repair or replace at our discretion any part found to be defective. We 34 Stephenson Way, cannot assume any consequential liability.