Understanding The Control Panel - Indesit WDE 12 X Instructions For Installation And Use Manual

Here I'm in command
Making the right choice is important. And it's easy.
Programme selector knob
Use this knob to select the wash
programme.
Turn this knob clockwise only.
To select a programme, you
should turn the knob so that the
symbol/number of the desired
programme is in line with the
pointer on the knob.
Now press on/off button H
(position I), pilot lamp I will start
flashing.
After 5", the setting will be
accepted, pilot lamp I will stop
flashing (staying lit) and the wash
cycle will begin.
Should you wish to interrupt the
programme in progress or set a
new one, select one of the
symbols (Stop/Reset) and wait
5" : when the cancellation has
been accepted, pilot lamp I
flashes, and you can then turn the
appliance off.
After the wash cycle has been set
and accepted by the washer-
dryer, turning the knob will have
no effect (except for when it is on
position Stop/Reset).
3
Instructions for installation and use
D
Temperature control knob
It is used to set the wash tempe-
rature in the recommended
programme table on pag. 4. It also
allows you to reduce the tempe-
rature recommended for the
selected programme, and even
to set a cold wash cycle ( ).
Drying cycle knob
Use this knob to select the
desired dr ying cycle. Two
options are available:
A - Based on time:
From 40 minutes to 150.
B - Based on the damp level of
the dry clothes:
Iron :slightly damp clothes,
easy to iron.
Wardrobe : dry clothes to
put away.
Extra dry
: very dry clothes,
recommended for towelling and
bathrobes.
A cooling stage is foreseen at
the end of the drying cycle.
Detergent dispenser
It is divided into 3 compartments:
1. Detergent for pre-wash;
2. Detergent for the main cycle
wash;
3. Fabric conditioner.
4
1
2
3

Understanding the control panel

C
The washer-dryer is equipped
with an extra compartment 4
(provided as an accessory) for
the bleach, to be inserted in
compartment 1.
Easy iron
This function allows your
washing to come out of the
machine without creases,
making it much easier to iron.
You can use it with programmes
3-4 (Cotton), 5-6 (Synthetics)
and 9 (Delicates).
Press this button
programmes 5-6-9 and the wash
cycle will come to a stop on
symbol . You can complete it
by pressing button E again.
Notes:
G
-
Iron
Slow spin
Use this button to reduce the
spinning speed from 1200 to
600 rpm for the cotton and linen
programmes and from 850 to
600 rpm for the synthetic
fabrics programmes.
Stain removal (see page 8)
Thanks to this command, the
washer-dryer will carry out a
more intensive wash that
optimises the effectiveness of the
liquid additives, thus allowing
more resistant stains to be
removed. When you press the
stain removal button, you cannot
activate the pre-wash.
E F G H
A
B
On-off
When button H is pressed, the
washer-dryer is switched on,
when it is not the machine is
switched off.
Turning the appliance off
does not cancel the selected
programme.
On-off lamp / door locked
Lamp I flashes slowly when the
appliance is switched on and
awaiting instructions and at the
in
end of a cycle, indicating that the
door can be opened. It flashes
quickly when the door should
not be opened. A steady light
means the appliance has
accepted the
programme.
Drying cycle lamp
When this lamp is on, it means
that knob C has been set on a
drying cycle and at the end of the
wash cycle, the appliance will run
the selected tumble drying cycle.
I
L
selected