Related Manuals for Atosa GR300
Summary of Contents for Atosa GR300
- Page 1 Gas Griddles Operating Instructions Before you begin, please read these instructions carefully to use this product correctly, to make the product perform ideally, and to avoid hazards. Models: GR300 / GR600 / GR900 / GR1200...
- Page 2 Dear customers and users： Thank you for purchasing our products. In order to be able to better use this product, please read these instructions carefully before any operation, and follow the guide, to avoid any unnecessary trouble during using. Please keep this instruction manual in a safe place for convenient reference and operation.
-
Page 3: Table Of Contents
Gas Griddles The Installation, Operation and Maintenance Guide Contents 1. Safety Protection ........- 3 - 2. Brief Instruction ........- 3 - 3. Manufacture’s Authority and Responsibility ..... - 3 - 4. Parameter Specifications ........ - 4 - 5. Transport and Storage ........- 9 - 6. -
Page 4: Safety Protection
1. Safety Protection Please make sure that the operator is an authorized and licensed technician before you allow him/her to install and operate the products. Be sure to strictly follow this instruction guide during installation and using. The manufacturer is not responsible for any danger or accidents caused by improper operation or maintenance. -
Page 5: Parameter Specifications
4. Parameter Specifications 4.1、Outline Dimensions(mm) AT80G3G-F AT80G3G-C - 4 -... - Page 6 AT80G6G-F AT80G6G-C - 5 -...
- Page 7 AT80G9G-F AT80G9G-C - 6 -...
- Page 8 AT80G12G-F AT80G12G-C - 7 -...
- Page 9 4.2：Size and package parameter information <Table 1> Overall Packing size Model dimensions L x W x H L x W x H AT80G3G-F 300*800*1115 395*875*640 AT80G3G-C 300*800*562 395*875*640 AT80G6G-F 600*800*1115 695*875*640 AT80G6G-C 600*800*562 695*875*640 AT80G9G-F 900*800*1115 995*875*640 AT80G9G-C 900*800*562 995*875*640 AT80G12G-F 1200*800*1115 1295*875*640 AT80G12G-C...
-
Page 10: Transport And Storage
4.3、Information of Gas Supply and Burner The minimum supplied gas pressure regulator is factory set at 1.13kPa for Natural Gas and 2.75kPa for L.P. Gas. The thread of product’s intake-tube is 3/4" BSP Female. <Table 2> #of burners Intake-tube Total Nozzle Rate Rate... - Page 11 by authorized and licensed technicians, otherwise the manufacturer has the right not to provide warranty service; Only be installed in accordance with AS/NZS 5601, the local gas, electricity and other relevant codes. 6.1、Unpacking and Installation Please dispose of all packaging materials and residues after unpacking; Check the equipment.
- Page 12 After installing completely, you should check gas supply pressure. Use a pressure gauge which is equipped with liquid (such as U-type pressure gauge, the minimum value is 0.1mbar) or a digital pressure gauge to test. Steps are as following: ●Remove top panel, and needle type pressure Needle type pressure joint joint screw arbor (Fig.1), then slip rubber tube of pressure gauge over needle type...
-
Page 13: Safety Notices And Precautions
7. Safety Notices and Precautions Warning! For your safety, do not place petrol and other flammables nearby. Please keep clean and free of flammables surroundings. Warning! Any erroneous installation, adjustment and refit may cause property damage or personal injury and maintenance failure. Read the instructions carefully before installation and using. -
Page 14: Operating Instructions
8. Operating Instructions Before operating, make sure place the unit horizontally by adjusting bottom adjustable legs, and place the catch tray properly. To ensure that the air flow in the bottom of the equipment . Do not use a fan or air conditioning to the flame, so as to avoid the flame extinguished and a safety accident. -
Page 15: Cleaning And Maintenance
8.3、Turn off the valve ①When the control knob is rotated to the fire position (Fig.3), the main fire burner flame is extinguished, but the pilot light will continue to work. ②Axial press the knob to rotate knob clockwise continually, so that the direction of the knob on the "O"... - Page 16 Warning: Before cleaning, all control valves must be turned off. Strictly follow the lighting instructions to work again after cleaning! Warning: Wait for the equipment to cool down after the unit has been turned off before you cleaning! Cut off the gas source as not in using; If the equipment is not used for a long time, clean the surface by wiping it with a soft cloth and place it in a well-ventilated area;...
-
Page 17: Troubleshooting
10. Troubleshooting <Table 3> Possible causes Problem solving Problems 1.Insufficient gas pressure 1.Contact the local in pipe gas supply dept. 2.Nozzle occlusion 2.Dredge nozzle 3.Thermocouple connection 3.Tighten Not lighting loose thermocouple 4.Replace 4.Thermocouple damage thermocouple 5.Replace 5.Gas control valve failure control valve 1.Insufficient gas pressure 1.Contact the local... -
Page 18: Installation Diagram Of Supporting Bracket
11. Installation diagram of supporting bracket - 17 -... - Page 19 But to update some components and necessary maintenance, can prolong life length of the products. Contact the dealer for assistance. For service and spare part inquiry, please contact following Atosa Catering Equipment Australia Pty Ltd 3-9 Forge Street,Blacktown,Sydney TEL: 1800 886 888...
Need help?
Do you have a question about the GR300 and is the answer not in the manual?
Questions and answers