Related Manuals for Keurig K-2550
Summary of Contents for Keurig K-2550
- Page 1 K-2550 ® Brewer Use & Care Guide Get the Most From Your New Keurig® Brewer Click Anywhere to Begin...
-
Page 2: Important Safeguards
If the pod does not on or taking off parts and before using only Keurig® K-Cup® pods be pulled on by children or fit, do not force the pod into the cleaning the appliance. -
Page 3: Table Of Contents
Menu Controls Kit (sold separately)................12 Adding Screensaver Images ........... 13 We recommend that you read through all instructions before BREWER CARE setting up or operating your K-2550® brewer................15 DESCALING ................... 18 TROUBLESHOOTING ............20 WARRANTY ..................21... -
Page 4: Brewer Parts
Power Switch Hot Water Drain Tube Water Inlet Port Cold Water Drain Tube Power Cord Filter Mounting Bracket Water Filter Outlet Tube Omnipure KQ8A Water Filter* 3/4” Garden Hose Connector *Sold separately. Contact your Keurig Authorized Distributor for more information. Continued... -
Page 5: K-2550® Water Reservoir Kit Parts
• If plumbing your brewer, refer to the “Plumbing Instructions” section on page 6 for water hookup. • If you have purchased the K-2550® Reservoir Kit, refer to the “Installing the Reservoir” section on page 8. *Sold separately. Contact your Keurig Authorized Distributor for more information. -
Page 6: Plumbing Instructions
125 psig. Consult a licensed plumber for water pressures in your area. Use plumbing fittings and tubing specified to withstand 125 psig. Screws (4x) WARNING: Keurig requires the use of an external water filter such as the Omnipure KQ8A Water Filter, available from Keurig. Failure to use a filter Filter Mounting OUT Port invalidates the brewer warranty. - Page 7 ® WATER HOOKUP, CONT. K-2500® BREWER K-2550® BREWER 5. Connect a stem elbow fitting to the IN port of the filter kit assembly by pushing the stem elbow fitting into the previously attached adapter. Push Screws (4x) firmly until the connection is secure. Secure LLDPE tubing to the stem elbow fitting in the same fashion and connect it to the local water supply.
-
Page 8: Installing The Reservoir
WATER HOOKUP, CONT. K-2500® BREWER K-2550® BREWER Installing the Reservoir If you have purchased the K-2550® Water Reservoir Kit, follow the simple instructions below to get it installed. NOTE: Rinse the reservoir with clean water prior to use. Remove Insert Dock... -
Page 9: Before You Brew
K-2550® BREWER Whether your brewer is plumbed or has the optional K-2550® Water Reservoir Kit installed, you will follow the same steps to get brewing. However, you may see different messages displayed on the touch screen, depending on which water source is installed. -
Page 10: Cleansing Brew
® BEFORE YOU BREW, CONT. BEFORE YOU BREW, CONT. K-2500® BREWER K-2550® BREWER Heating... Plumbed brewer shown Heat Up Lift & Lower Cleansing Brew Once the brewer fills the internal hot Place a mug on the drip tray plate When prompted to select your... - Page 11 ® BREW YOUR FIRST CUP BREW YOUR FIRST CUP K-2500® BREWER K-2550® BREWER Brewer with reservoir shown 1. Place Mug & Pod Place a mug for hot or tumbler for iced on the drip tray plate. NOTE: Do not remove the foil lid on the K-Cup® pod.
-
Page 12: Brewer Features & Controls
To temporarily change the language for a single brew, simply press the button for your language of choice on the Commercial Rating: Ensures that the K-2550® brewer will stand up to the touch screen while it’s in its idle state. -
Page 13: Brewer Care
K-Cup® pod holder to release. Then lift it up to remove. After cleaning, align the K-Cup® pod Keep your Keurig® brewer looking its best by cleaning the exterior from time holder with the opening, using the two front to time. Just clean with a paper towel and a nonvinegar glass cleaner. - Page 14 ® BREWER CARE, CONT. K-2500® BREWER K-2550® BREWER Entrance Needle For Plumbed Brewers: Disconnect the water line. The entrance needle is located on the underside of the lid. Open the descale solution door and fill Link on how to clean entrance needle: the internal tank with approximately https://vimeo.com/430384922...
- Page 15 (such as chlorine or mineral tastes), we recommend using bottled to let it warm to room temperature for at least two hours before using. or filtered water. Do not use distilled water. You can also install a Keurig® Changing the Water Source Water Filter to help remove water impurities and improve beverage taste.
-
Page 16: Power Off
The descaling procedure differs slightly between plumbed brewers and the access door. This step may take brewers installed with the optional K-2550® Water Reservoir Kit. Please make up to five minutes. sure you are following the proper steps based on which water source your brewer uses. -
Page 17: Descaling
The last eight should clear any the PM to dry after completing all hot water tank. Raise the lid handle of the Keurig® Descaling Solution remaining solution from the walls of cleansing brews. This can be done to initiate a 12oz cleansing brew. -
Page 18: Troubleshooting
Brewer produces only a partial cup • The exit or entrance needle may be clogged • Clean K-Cup® pod holder if necessary and rinse under faucet • If the brewer is alerting you to perform a “Descale,” have your Keurig Authorized Distributor descale the brewer... -
Page 19: Warranty
Keurig® K-Cup® brand pods and accessories will guarantee the proper functioning warranty servicing. simply call your Keurig Authorized Distributor (KAD) who and lifetime of your Keurig® K-Cup® brewer. Any damage to or malfunction of your brewer resulting from the use of non-Keurig® K-Cup® brand pods and accessories...
Need help?
Do you have a question about the K-2550 and is the answer not in the manual?
Questions and answers
How many amp do I need for this Machine