Summary of Contents for Hauff-Technik HAW-E ETGAR BHP SET
Page 1
Montageanleitung - HAW-E ETGAR BHP SET Installation instructions - HAW-E ETGAR BHP SET Vor Beginn der Montage Anleitung lesen und gut aufbewahren! www.hauff-technik.de ...
Page 9
Bei der Montage der Hausausführung müssen die entsprechenden Vorschriften der Berufsgenossenschaften, die VDE-Bestimmungen, die entsprechenden natio- wenden. Wir empfehlen den Kabelreiniger KRMTX. • Weiteres Zubehör und Informationen unter www.hauff-technik.de und in den nalen Sicherheits- und Unfallverhütungsvorschriften sowie die Richtlinien (Arbeits- und Verfahrensanweisungen) Ihres Unternehmens beachtet werden.
VDE provisions, the relevant national lich! safety and accident prevention regulations and your company’s guidelines (work Zum Lieferumfang der Hausausführung HAW-E ETGAR BHP SET gehören: and procedure instructions). The fitter must wear the relevant protective clothing.
Page 11
• 1 tube of GMT lubricant Scope of delivery for the standard design. Deviations are possible due to individual combinations. The scope of delivery of the Building services outlet HAW-E ETGAR BHP set in- cludes: • 1 ETGAR building services outlet •...
Hausausführung HAW-E ETGAR BHP Akkuschrauber anziehen, bis die gelben Druckstifte/Kontrollstifte bündig mit der Frontplatte abschließen oder ein Dreh- moment von 6 Nm erreicht ist (siehe Abb.: 6 und 7). 4 Beschreibung Legende zu Abb.: 7 Beispiel Hausausführung HAW-E ETGAR BHP mit Außen- gelber Druckstift/Kontrollstift dichtelement Modul 1 (siehe Abb.: 1).
Hausausführung HAW-E ETGAR BHP Gebäudeaußenseite • Das max. Volumen des Harzes wird nach ca. 5 Gummilippen des Flansches mit Gleitmittel einstrei- min. erreicht. chen (siehe Abb.: 11). • Die komplette Aushärtezeit beträgt ca. 30 min. Schutzfolie vom Butylband des Gummiflansches ab- ziehen, bis an die Gebäudeaußenseite schieben und 13 Zum Schluss den Harzeinfüllschlauch mit Hilfe eines leicht andrücken (siehe Abb.: 12).
Hausausführung HAW-E ETGAR BHP Dämmscheibe über das Mantelrohr, bündig in die Hausausführung und Wellrohr DN75 schieben (siehe ausgeschnittene Öffnung der Perimeter-Dämmung Abb.: 39). schieben (siehe Abb.: 31). Die Original-Profildichtringe der Kabuflex/Unicor- Wellrohre dürfen nicht verwendet werden (siehe 10 Außendichtelement ETGAR AD (Modul Abb.: 40).
Hausausführung HAW-E ETGAR BHP 12.3 Tabelle 2 Dichtelemente Modul 1 Modul 3 Anwen- Segment- Istmaße Rohr/Ka- dungsbe- Segment- beldurch- ring Perimeterdämmung reich schnitte messer d (mm) (mm) 13.2 Betonierte Wand mit Außenabdichtung nach (siehe auch Be- schriftung auf DIN 18533 W2.1-E und Perimeterdämmung den Manschet- tenstopfen) ETGAR...
Hausausführung HAW-E ETGAR BHP 13.5 Doppel-/Elementwand mit Außenabdichtung nach DIN 18533 W2.1-E und Perimeterdäm- mung innen HAW-E ETGAR BHP mit Modul 1 und Modul 1.2 (siehe Abb.: 50). Legende zu Abb.: 50 Doppel-/Elementwand Modul 1 Modul 1.2 Perimeterdämmung innen KMB-/PMBC-Beschichtung außen 13.6 Betonierte Wand mit Außenabdichtung nach DIN 18533 W2.2-E (z.B.
DIN 18533 W2.1 is possible. Module 8 is included in the Building services out- 5 Preparing installation let HAW-E ETGAR BHP SET. Check diameter (D) of core hole/casing pipe at two • Openings in the core drill hole on the outside points (vertical and horizontal) and wall thickness (X) of the building (see Fig.
Building services outlet HAW-E ETGAR BHP exterior of the building 13 Finally, cut the resin filling hose flush with the flange Apply lubricant to the rubber lips of the flange (see using a side cutter (see Fig. 23). Fig. 11). •...
Building services outlet HAW-E ETGAR BHP 10 Installing ETGAR AD external sealing ele- Completed connection of casing pipe Building ser- vices outlet with DN75 double sleeve to ETGAR corru- ment (module 6.2) (when installing in a gated pipe (see Fig. 41). core drill hole) 12 Sealing elements The ETGAR AD (module 6.2) is required for in-...
Building services outlet HAW-E ETGAR BHP 12.3 Table 2 Sealing elements 13.1 Concrete wall (waterproof concrete) with pe- rimeter insulation Applica- Segment Actual di- Pipe/cable mensions diameter d tion range ring of seg- (mm) HAW-E ETGAR BHP with Module 1 and Module 3 (see ment sec- Fig.: 46).
Building services outlet HAW-E ETGAR BHP KMB/PMBC coating Perimeter insulation 13.5 Double wall/element wall with external wa- terproofing according to DIN 18533 W2.1-E and perimeter insulation, inside HAW-E ETGAR BHP with Module 1 and Module 1.2 (see Fig. 50). Key to Fig.: 50 Double wall/element wall Module 1 Module 1.2...
Need help?
Do you have a question about the HAW-E ETGAR BHP SET and is the answer not in the manual?
Questions and answers