For the SolarEdge Home Battery - Emergency
Response guide, including emergency phone
numbers, see:
https://www.solaredge.com/sites/default/files se-
energy-bank-emergency-response-guide.pdf
Support Contact Information
In case of any technical issues with SolarEdge
products, please contact us at:
https://www.solaredge.com/service/support
© SolarEdge Technologies, Ltd.
All rights reserved.
Version: 1.1, January 2025
Subject to change without notice.
What's in the Package
Mounting
bracket screws
Mounting bracket
SolarEdge Home
Decorative cover
Battery
The SolarEdge Home Battery 400V can be added to your SolarEdge All-in-One residential system. This battery is
intended for storing excess solar production and delivering backup power.
WARNING!
This symbol on the product or in the accompanying documentation denotes a hazard. It calls attention to a procedure
that, if not correctly performed or adhered to, could result in injury or loss of life. Do not proceed beyond a warning
note until the indicated conditions are fully understood and met.
WARNING!
Before installing or operating the SolarEdge Home Battery (referred to as the
instructions at the back of this page.
1
"
24
16
"
2
1
3
m in 8
"
m ax 164 ft
4
2
3
2
CAUTION!
3
2
1
x 2
x 2
MC 4
Conduit
Cover
connectors
holder
screws
"
"
Battery
), read the Safety and Handling
Install mounting bracket
When selecting the installation location:
Maintain a clearance of min 8
"
from other
•
objects.
Make sure the max distance from the inverter is max
•
164ft.
Make sure the installation surface sustains the weight
of the battery (267lb).
1.
Level the bracket.
2.
Mark two drilling spots.
Use either the inner or outer pair of holes.
If necessary, you can use the additional holes to secure
the bracket.
3.
Drill holes in the installation surface.
4.
Install the mounting bracket and secure with screws.
Transport battery
1.
Screw in all FOUR handles to the battery frame.
Make sure to screw in the handles all the way.
1
Do not use a bent, cracked, or otherwise damaged
handle.
2.
Place the battery upright on a dolly and secure it with
straps.
Caution!
Stand the battery on the rubber protector only!
3.
Transport the battery to the installation location.
Hang battery on
mounting bracket
1.
Lift the battery to the height of the mounting bracket.
2.
Hang the battery on the mounting bracket, while
holding it by the handles.
3.
Secure with a mounting bracket screw (supplied) on
each side. Apply a torque of 42lbf·in.
3
Quick Installation
Guide
Version 1.1
Required Personnel and Tools
MC 4 crimper
Drill
8/ 10/12 AWG
min 2
Mounting
DC cable
Min 2 qualified
screws -
600V insulated
installers
m ax M10
T orque
Phillips
wrench
screwdriver
4
4
3
2
1
5
3
-
+
Home Netw
2
1
OFF
6
1
ON
2
I
P
0
2 sec
SolarEdge
Home Battery 400V
for use with SolarEdge Inverters
North America
x 4
Handles (available
Level
from SolarEdge)
Dolly with lift
and ratchet straps
x 2
Long-nose
Branch connectors
SolarEdge
( optional, available
pliers
Home Network
from SolarEdge)
plug-in (available
from SolarEdge)
Prepare cables
1.
Mount the conduit holder.
2.
Pass the DC cables and grounding cable through the
conduit holder at the bottom of the battery.
3.
Connect the grounding cable to the grounding
terminal with a torque of 66 in*lbs/7.5 N*m.
4.
Crimp the DC cables to the MC4 connectors
(supplied) and tighten the MC4 connector glands
with a torque of 30lbf·in
Connect to inverter
1.
Make sure the inverter is OFF.
2.
Connect the DC cables to the DC+ and DC- inputs.
Observe correct polarity.
3.
Install the SolarEdge
Home Network
plug-in and antenna
in the inverter. See the
Installation
guide
4.
Connect cables to the inverter.
See the
Connection and Configuration
ork
application note.
5.
For multiple SolarEdge Home Batteries
connection, see
Connecting the Home
4
Hub Inverter to multiple Home Batteries
Power on and associate
1.
To power on and operate the battery, turn on the DC
circuit breaker, and set the P/1/0 switch to
2.
To associate with the inverter, hold the battery
P/1/0 switch to P for 2 seconds and then release.
NOTE!
To power OFF the battery, follow these steps:
1.
Set the P/1/0 switch to
"
0
"
(OFF).
2.
Turn off the DC circuit breaker.
IMPORTANT NOTE!
If the inverter is turned off or in fault state, make sure to
turn off the battery to maintain its lifetime.
"
"
1
(ON).
'
s
Need help?
Do you have a question about the Home Battery 400V and is the answer not in the manual?
Questions and answers