Related Manuals for Home Accents Holiday 1005 158 902
Summary of Contents for Home Accents Holiday 1005 158 902
- Page 1 SKU#1005 158 902 INSTRUCTION MANUAL SET-UP INSTRUCTIONS FOR THE 5 FT ANIMATED LED HEARSE 1-877-527-0313, 8 a.m. to 5 p.m., EST, info@pan-asian.com.hk. Monday-Friday...
- Page 2 READ CAREFULLY & RETAIN FOR FUTURE REFERENCE! Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-527-0313, 8 a.m. to 5 p.m., EST, Monday-Friday or email at info@pan-asian.com.hk. WARNING: This is not a toy and is for decorative purposes only. For incoor/outdoor use. This item is not intended for use by children under the age of 14.
-
Page 3: Safety Instructions
SAFETY INSTRUCTIONS: 1. All cautions in these operating instructions should be followed completely. 2. Do not use near water; such as bathtub, laundry tub, kitchen sink, wet basement or swimming pool, etc. 3. Do not display figure near any heat source such as radiators, stoves, fireplaces, etc. -
Page 4: Part List
PART LIST: Carriage Base - Front Carriage Base - Middle Carriage Base - Back Carriage Base Carriage Panel with Plastic Screwdriver Screws Try Me button - Front Carriage Side Carriage Panel - Back Carriage Top Panel - Front Carriage Top Panel - Back Lantern Decorative Molding Details... - Page 5 Screws for Wheel and Lantern Wheels Wheels Connector Support X 10 Skeleton Driver with Try Me button Bridle and Hat NOTE: If any parts are broken or missing first call the customer care number 1-877-527-0313...
- Page 6 ASSEMBLY: (Assembly Takes Approximately 45 Minutes with 2 Adults) Step 1 Step 2 Step 3...
- Page 7 Locking Clip Step 4 Adjust the screws located under the four support rods, make sure the base is secure and level. Step 5...
- Page 8 F&H F&H (inside) (inside) (inside) (inside) Step 6 Locking Clip...
- Page 9 Step 7 Turning the locking tap to secure the carriage panel into the base after attached parts F, G and H. Step 8 Attach the lantern's lead wires through the hole located on the front carriage panel (parts F). (inside) Step 9...
- Page 10 Step 10 PARTS J PARTS I (Top of Carriage) (Top of Carriage) Locking Clip Step 11 Step 12 Step 13 Turning the screws to secure the top panel into the carriage panel.
- Page 11 Step 14 Step 15 Using plastic screw driver (included) screw down parts A and B of the 4 points shown.
- Page 12 Step 16 Step 17...
- Page 13 REPEAT THE PROCESS ON THE OTHER WHEELS UNTIL ALL 4 WHEELS ARE Step 18 LOCKED INTO PLACE, AS SHOWN Step 19...
- Page 14 TRY ME Jack Step 23 Turn switch to ON position located in the front of the Carriage Step 20 Panel (Parts F) Step 21 Step 22 (inside)
- Page 15 Step 24 Step 25 Turn switch to ON position located in the back of the Driver Locking...
- Page 16 Step 26 Hook and loop closure Step 27 Bridle...
- Page 17 HOW TO ATTACH THE BRIDLE INTO THE SKELETON PONY (SKELETON PONY NOT INCLUDED) Step 28 Step 29 Step 30 Step 31A Step 31 Attach the bridle into the Driver’s hand SKELETON PONY NOT INCLUDED...
-
Page 18: Troubleshooting
BATTERY REPLACEMENT & ITEM FUNCTION FOR HEARSE: Battery-powered. Requires 3 “AA” batteries for Hearse (included). 1. Remove the battery case cover, which is located on the producr. unscrew the safety screw and then remove the battery compartment cover. 2. Clean the battery contacts and also those of the device prior to battery installation. 3.
Need help?
Do you have a question about the 1005 158 902 and is the answer not in the manual?
Questions and answers