Asus TP470 Series Repair Manual
  1. Manuals
  2. Brands
  3. Asus Manuals
  4. Laptop
  5. TP470 Series
  6. Repair manual
Asus TP470 Series Repair Manual

Asus TP470 Series Repair Manual

Hide thumbs

Advertisement

Table of Contents

Disassembly Procedure
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TP470 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Asus TP470 Series

Summary of Contents for Asus TP470 Series

  • Page 1 Disassembly Procedure...
  • Page 2 Disassembly Procedure...

  • Page 3: Service Overview

    Disassembly Procedure Service Overview...
  • Page 4 Disassembly Procedure Pre-repair checklist...
  • Page 5 Disassembly Procedure Repair Overview Please pay special attention to the cautions below to prevent any damages to the notebook and please be sure to select the appropriate tools described in this section to perform any services desired. Precautions Before you perform any service or repair on the notebook, please follow the steps below first. 1.
  • Page 6 Disassembly Procedure Screw Appearance Criteria. If the screws have the following damaged appearance, please do not use. a. Shape deformed. b. Paint scratched off. c. Rusty. d. Damaged head – unable to drive in. e. Damaged unable to securely tighten. 10.The following chapter includes all part numbers mentioned in service guide are used for reference only, actual part name depends on different SKU, if you need the exact part number for ordering please refer to the orderbook.
  • Page 7 Disassembly Procedure Appropriate Tools The illustrations below show the appropriate tools that should be used for the notebook’s service and repair. ➢ Cross Screwdriver Please accord to different screw specification to choose different screwdriver and head. Below photos are for reference only. Use a cross screwdriver to fasten/remove screws.
  • Page 8 Disassembly Procedure ➢ Thickness gauge Thickness compass specification 0.05mm-1.5mm. Use it to measure the gap.
  • Page 9 Disassembly Procedure Bottom Case Module The illustrations below show how to remove the Bottom Case Module. Notice: After disassembling bottom case, if you want to replace any part, please be sure to disconnect the battery connector more than ten seconds to avoid damaging any part. 1.
  • Page 10 Disassembly Procedure Step 2: please remove the two rubbers on the bottom then remove the screws under the rubber. 2. Use plastic blade to pry Bottom Case and remove it. Notice: Please follow above arrow direction with using plastic blade to pry bottom case in each blue circle location.
  • Page 11 Disassembly Procedure Parts: ⚫ Total screw * 12 ⚫ TP470EZ-2K BOTTOM CASE SUB ASSY*1 ⚫ TP470EZ-2K BOTTOM CASE RUBBER*1 (Actual part name depends on different SKU)
  • Page 12 Disassembly Procedure Notice: If want to reuse the BOTTOM CASE, please check the position of the red • mark below (Figure 1), If the hook is damaged by BEND/BROKEN (Figure 2), please use the trimming tool/cutting Pliers to trim the damage hook (Figure3), then check the "no gap"...

  • Page 13: Battery Module

    Disassembly Procedure Battery Module The illustrations below show how to remove the Battery Module. Push back the anti-off metal then disconnect the battery cable from MB. Notice: Before disassembly, please be sure to pull out adapter and disconnect the battery more than ten seconds in order to avoid IC damage.
  • Page 14 Disassembly Procedure Parts: ⚫ Total screw * 4 ⚫ X421 BATT *1 (Actual part name depends on different SKU)

  • Page 15: Ssd Module

    Disassembly Procedure SSD Module The illustrations below show how to remove the SSD Module. Remove the 1 screw on the SSD. 2. Remove SDD, shows as below. SCREW M2*2L (6.2,0.55) (K) #1 Parts: ⚫ Total screw * 1 ⚫ SSD P3X4(VAL) 512GB M2 2280 NVME*1 (Actual part name depends on different SKU.)

  • Page 16: Wlan Module

    Disassembly Procedure WLAN Module The illustrations below show how to remove the WLAN antenna Module. 1. Disconnect the WLAN antenna connector from the MB. Assembly Notice: Black main cable connect the indicator number 2(▲MAIN), white aux cable connect the indicator number 1(∆AUX). 2.
  • Page 17 Disassembly Procedure SCREW M2*2L (6.2,0.55) (K) Parts ⚫ WIFI6 AX+BT5.0(2*2)M.2 2230 G+ *1 ⚫ Total SCREW*1 (Actual part name depends on different SKU.)
  • Page 18 Disassembly Procedure Fan & Thermal Module The illustrations below show how to remove the fan Module. Pull out the Fan Cables firstly then remove 11 screws on the thermal and the fan. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque: 2.0KG±0.2kgf...
  • Page 19 Disassembly Procedure SCREW M2*3L (K) B-ZN,NY #1...
  • Page 20 Disassembly Procedure Notice：Please use the correct technique of taking fans in order to avoid being out of shape. Correct demonstration Wrong demonstration Location:[ CPU&GPU] Thermal material:GA500 Grease Thermal grease thickness = 0.2 ~ 0.3mm thickness about 0.2~0.3mm Parts: ⚫ Total screw * 11 ⚫...

  • Page 21: Touchpad Module

    Disassembly Procedure Touchpad Module The illustrations below show how to remove the Touchpad Module. 1. Tear off the black rubber on the touchpad Assembly notice: when you assemble the touchpad please make sure attach the black rubber. 2. Disconnect the FFC.
  • Page 22 Disassembly Procedure 3. Tear off the Gasket Tape Notice: The TP Gasket Tape must be stuck well when it is assembled. 3. Remove 3 screws on Touch Pad and take out the Touch Pad . Assembly Notice: follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2KG±0.2kgf.
  • Page 23 Disassembly Procedure SCREW M2*2.5L (7,0.55) (K)#1 Assembly notice: Please change new one, If FFC is damage during disassembly. Here are some samples of FFC damage: Parts: ⚫ Total screw * 3 ⚫ TP470EA TP FFC 8P,0.5MM,L97.5*1 ⚫ TP470EZ-2K NUMPAD MODULE*1 ⚫...
  • Page 24 Disassembly Procedure PUR board Module The illustrations below show how to remove the PUR board Module. 1. Disconnect the PUR FFC cable from the PUR and Disconnect the PUR FFC cable from the MB board then remove 1 screw, shows as below. Assembly Notice: Follow the reverse numbers to lock screws.
  • Page 25 Disassembly Procedure 2. Check the PUR board, shows as below. Parts ⚫ TP470EZ POWER SWITCH_BD/AS*1 ⚫ Total screw *1 ⚫ TP420IA PW TO MB FFC ZIF 8PIN 44.5MM*1 (Actual part name depends on different SKU.)
  • Page 26 Disassembly Procedure Motherboard Module The illustrations below show how to remove the Motherboard Module. Disconnect Speaker cables, Back light cable, keyboard cable on the MB。 2. Disconnect FFC cables, EDP cable, Coms cable, on the MB Main antenna cable then remove 3 screws which locked on the right hinge and the 2 screws which locked on the MB, shows as below.
  • Page 27 Disassembly Procedure Assembly notice: Please change new one, if FFC damaged during disassembly. There are some FFC cables damaged sample.
  • Page 28 Disassembly Procedure 3. Take off the motherboard from bottom case, shows as below. 4. Check the material on motherboard, shows as below. TP470EZ TH MYLAR...

  • Page 29: Speaker Module

    Disassembly Procedure TP470EZ CPU BRACKET TP470EZ MB MYLAR Parts: ⚫ Total screw *5 ⚫ TP470EZ MB._16G/I7-1165G7/AS*1 (Actual part name depends on different SKU.) Speaker Module The illustrations below show how to remove the antenna & speaker Module. 1. Tear off the gasket follow the picture .
  • Page 30 Disassembly Procedure 2. Reomve the speaker. Assembly Notice: Must place the speaker cables in the hook slot carefully as below and stick TP conductive sponge. And the speaker cable should be under the FFC/FPC cables. 3. Separate the speaker and antenna module. Assemble Notice: Please align the pin to assemble the speaker module.
  • Page 31 Disassembly Procedure Parts: ⚫ TP470 SPEAKER MODULE*1 (Actual part name depends on different SKU.) USB board Module The illustrations below show how to remove the USB board Module. 1. Remove 2 screws which locked on the left hinge and the 2 screws which locked on the Main board, then disconnect the USB FFC cable from the USB board , shows as below.
  • Page 32 Disassembly Procedure Main antenna Module The illustrations below show how to remove the MAIN antenna Module. Remove the Main antenna Module, and tear off the gasket as below. Assembly Notice: Must place the main antenna cables in the hook slot carefully as below. Assembly Notice: please replace a new one when you tear off the gasket whose location shows as below.
  • Page 33 Disassembly Procedure Snap as below: Parts ⚫ TP470 WIFI MAIN ANTENNA*1 (Actual part name depends on different SKU.)

  • Page 34: Lcd Module

    Disassembly Procedure LCD Module The illustrations below show how to remove the LCD Module. 1. Use disassembly tool to pry up the LCD bezel cap firstly, shows as below. 2. Remove the bezel cap, shows as below. 3. Remove rubber in the hinges gap, shows as below.
  • Page 35 Disassembly Procedure 4. Disconnect the EDP cable two cables of LCD panel then Remove the , shows as below. TOUCHPANEL CONTROL_BD...
  • Page 36 Disassembly Procedure Assembly notice: when you assemble the LCD module please paste the ACETATE TAPE on the screw follow the steps Step1: ACETATE TAPE should align the red box. Step2. Please put the ACETATE TAPE under the panel by the tweezers and make sure the ACETATE TAPE is smooth and the whole screw was covered by the ACETATE TAPE like the picture.
  • Page 37 Disassembly Procedure Parts: ⚫ TP470EZ-2K 14.0' FHD/G/T/VWV*1 ⚫ TP470EZ HINGE CAP RUBBER R*1 ⚫ TP470EZ HINGE CAP RUBBER L*1 ⚫ TP470EZ BEZEL DOWN DECO ASSY*1 (Actual part name depends on different SKU.)

Table of Contents