Asus TP401MA Series Repair Manual
Asus TP401MA Series Repair Manual

Asus TP401MA Series Repair Manual

Hide thumbs Also See for TP401MA Series:

Advertisement

Disassembly Procedure
ASUS TP401MA Series
Repair Manual
2 - 1
V1.0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TP401MA Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Asus TP401MA Series

  • Page 1 Disassembly Procedure ASUS TP401MA Series Repair Manual 2 - 1 V1.0...
  • Page 2 Disassembly Procedure 2 - 2 V1.0...
  • Page 3 Disassembly Procedure 2 - 3 V1.0...
  • Page 4: Service Overview

    Disassembly Procedure Service Overview 2 - 4 V1.0...
  • Page 5 Disassembly Procedure Pre-repair checklist 2 - 5 V1.0...
  • Page 6 Disassembly Procedure Appropriate Tools The illustrations below show the appropriate tools that should be used for the notebook’s service and repair. Cross Screwdriver Please according to different screw specification and choose different screwdriver and head. Below photos are for reference only. Use a cross screwdriver to fasten/remove screws.
  • Page 7 Disassembly Procedure Thickness gauge Thickness compass specification 0.05mm-1.5mm Use it to measure the gap. Hand rollers Use the roller to press touch pad mylar. 2 - 7 V1.0...
  • Page 8 Disassembly Procedure Bottom Case Module The illustration below shows how to remove the bottom case module. 1. Pry up two rubbers and follow below numbers to remove 2 screws. 2. Follow below numbers to remove 13 screws on the Bottom case module. Assembly Notice: Follow the reverse numbers to lock screws.
  • Page 9 Disassembly Procedure SCREW M2*5.5L (4,0.8) (K)#1 SCREW M2*4.5L (4,0.8) (K) #1 SCREW M2.5*4L (K) B-ZN NY #1 Snaps as below: 2 - 9 V1.0...
  • Page 10 Disassembly Procedure 3. Pry up the bottom case and take it away. Parts ⚫ Total screw *13 ⚫ Screw rubber *2 BOTTOM CASE*1 2 - 10 V1.0...
  • Page 11: Battery Module

    Disassembly Procedure Battery Module The illustration below shows how to remove the battery module. 1. Disconnect battery connecter. 2. Follow below numbers to remove 2 screws on the Battery module and take it away. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 1.5±0.2kg SCREW M2*3L D4.5 (K) W-NI NY Parts...
  • Page 12: Speaker Module

    Disassembly Procedure Speaker Module The illustration shows how to remove the speaker. 1. Disconnect speaker and WLAN antenna, then take speaker away. Assembly Notice: Black cable is connect to the “MAIN” input port, White cable is connect to the “AUX” port. Please well arrange the speaker cables and put it in the hook slot as below.
  • Page 13: Touchpad Module

    Disassembly Procedure Touchpad Module The illustration below shows how to remove the touchpad module. 1. Tear off the gasket. 2. Tear off the gasket . Please stick the gasket well when you assemble it. 3. Disconnect FFC from MB and follow below numbers to remove 3 screws on touchpad. Assembly Notice: Follow the reverse numbers to lock screws.
  • Page 14 Disassembly Procedure 4. Disconnect TP FFC from touchpad. Parts: ⚫ Total screw *3 ⚫ Touchpad module *1 ⚫ TP FFC *1 2 - 14 V1.0...
  • Page 15 Disassembly Procedure IO BOARD The illustration below shows how to remove IO board. 1. Disconnect the IO FFC from MB Follow below numbers to remove 2 screws on IO board and take it away. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 1.5±0.2kg SCREW M2*3L D4.5 (K) W-NI NY 2 - 15...
  • Page 16 Disassembly Procedure Disconnect the IO FFC from IO board. Parts: ⚫ Total screw *2 ⚫ TP401MA IO_BD.//R2.0 *1 ⚫ TP401MA IO FFC 24P 0.5 L109 *1 2 - 16 V1.0...
  • Page 17: Wlan Module

    Disassembly Procedure WLAN Module The illustration shows how to remove the WLAN Module. 1. Remove 1 screw on WLAN card and take it away. Assembly Notice: Screw tightening torque (Kg F-cm): 2.0±0.2kg SCREW M2*1.5L (4.5,0.8) (K) #1 Parts: ⚫ Total screw *1 ⚫...
  • Page 18: Main Board

    Disassembly Procedure Main Board The illustrations below show how to remove the main board. Remove 6 screws on hinge and disconnect EDP and touch control cable. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.5±0.2kg, SCREW M2.5*4L (K) B-ZN NY #1 2 - 18 V1.0...
  • Page 19 Disassembly Procedure Remove 4 screws on mainboard. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0±0.2kg, Screw tightening torque (Kg F-cm): 2.0±0.2kg, SCREW M2*4.2L (4.5,0.6) (K) #1 SCREW M2*3L (K) B-ZN #1 NY Disconnect KB FPC and take MB away. 2 - 19 V1.0...
  • Page 20 Disassembly Procedure Remove 2 screws on thermal then take it away. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 1.5±0.2kg SCREW M2*2L (4.5,0.8) (K) #1 Assemble Notice: 1.After replace new MB, please clean remaining CPU and GPU thermal pad on thermal module and then paste new one.
  • Page 21 Disassembly Procedure Notice: These pictures for your reference for mylar/gasket/sponge etc. of MB. 2 - 21 V1.0...
  • Page 22: Lcd Module

    Disassembly Procedure LCD Module The illustration below shows how to remove the LCD module. 1. Use tweezers to pry up rubber and remove 2 screws. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 1.5±0.2kg SCREW M2*3L (4.5,0.5) (K) B-ZN 2 - 22 V1.0...
  • Page 23 Disassembly Procedure Use tweezers to pry up LCD bezel and take it away. Assembly Notice: Please follow the “OK” picture to assemble the EDP Cable. 2 - 23 V1.0...
  • Page 24 Disassembly Procedure Snaps as below: 2 - 24 V1.0...
  • Page 25 Disassembly Procedure 3. Tear off the tape and disconnect EDP cable. 4. Disconnect CMOS TP CABLE. Assembly Notice: Please well arrange the cables and put it in the hook slot as below. 2 - 25 V1.0...
  • Page 26 Disassembly Procedure 5. Separate camera from CMOS TP cable. 6. Disconnect touch control cable and take touch control board away. 7. Remove 6 screws from hinge and take hinge away from LCD cover. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 2.0±0.2kg 2 - 26 V1.0...
  • Page 27 Disassembly Procedure SCREW M2*2L (6.2,0.55) (K) #1 2 - 27 V1.0...
  • Page 28 Disassembly Procedure Remove 2 screws on hinge and take hinge cap away. Assembly Notice: Follow the reverse numbers to lock screws. Screw tightening torque (Kg F-cm): 1.3±0.2kg SCREW M1.6*3L (4.5,0.6) (K) #0 KL MACHINE NY B-ZN Parts ⚫ Total screw *10 ⚫...

Table of Contents