Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for RunCam T1
Summary of Contents for RunCam T1
- Page 1 RunCam T1 Manual...
- Page 2 Installation Method Integrated Split Diagram WiFi Button SD Card Slot Indicator Light 3 Screen Mount Antenna Screen （3D-Printed Pa爀琀） Type-C Po爀琀 Speaker HDMI Camera Batte爀礀 Power Po爀琀 Indicator Light 4 Ethernet Po爀琀 Indicator Light 2 Indicator Light 5 Microphone Camera Slot Indicator Light 6 Indicator Light1 Power/Shutter Button...
-
Page 3: Power Supply
Indicator Lights Status Type-C Ethernet Firmware WiFi Indicator Color Standby Card Error Recording Charging WiFi On Charging Connected Upgrade Connected Blue Solid Fast Flash Slow Flash Solid Solid Solid Solid Solid Alternating Indicator1 Flash Alternating Solid Solid Solid Fast Flash Slow Flash Solid Solid... -
Page 4: Touch Screen Operations
Touch Screen Operations Record mode 2024/01/01 00�00�00 2024/01/01 00�00�00 resolution resolution frame rate frame rate 2.7k 2.7k 1080p 1080p 25fps 25fps 25fps 1440p 1440p 25fps 30fps 30fps 1080p 1080p 50fps 50fps 720p 720p Swipe left to swipe up/down swipe right to resolution takes e昀昀ect left to return right to select... -
Page 5: Firmware Upgrade
For optimal pe爀昀ormance, upgrade to the latest 昀椀rmware version (Suppo爀琀s FAT32 SD cards only). Upgrade Status: Red, blue, and yellow lights alternate 昀氀ashing, and the screen shows the SYSTEM UPGRADE. After completion, the camera resta爀琀s. Upgrade instructions: SYSTEM https://www.runcam.com/download/RunCamT1 UPGRADE... - Page 6 Hardware Inte爀昀ace Instructions Type-C Po爀琀 Powers the mainboard and charges the batte爀礀 Suppo爀琀s 5V USB power input. (green light solid on while charging, o昀昀 when fully charged). Inse爀琀 SD card, connect via USB, and the camera will enter U-Disk U-Disk Mode (connected to a computer) mode to access SD card 昀椀les.
- Page 7 Wired VTX Use a JST SH 1.25mm 6-pin cable to connect the camera to the Ethernet. Set the camera's network output to Ethernet, then connect the camera to the computer. Once connected, con昀椀gure the network on the computer. Windows （1）Open "Control Panel," go to "Network and Sharing Center," 昀椀nd the Ethernet network, and open its "Prope爀琀ies." （2）Double-click "Internet Protocol Version 4 (TCP/IPv4)".
- Page 8 Follow the steps indicated in the image, copy this address: 爀琀sp://192.168.10.2/liveRTSP/av4, paste it into the 昀椀eld marked ④, and click “Play” to enable the real-time preview in recording mode. ② ③ ① ④ UART Con昀椀guration Refer to the document: Simpli昀椀ed Protocol.docx. Technical Suppo爀琀 Visit: [RunCam Suppo爀琀](https://suppo爀琀.runcam.com/hc/en-us).
- Page 9 Speci昀椀cations RunCam T1 Name Sony IMX415 Sensor 4K：3840x2160@25/30fps 2.7K：2704x1520@25/30fps 1440P：2560x1440@25/30fps 1080P：1920x1080@25/30/50/60fps Video Resolution 720P：1280x720@25/30/50/60fps 2M：1920x1080 3M：2304x1296 5M：3072x1728 8M：3840x2160 Photo Resolution 10M：4240x2384 12M：4608x2592 13M：4800x2700 20M：6016x3384 Video Forma Photo Format Normal Recording, Slow Motion, Loop Recording, Pre-Recording Recording Modes Normal Photo, Time-Lapse, Burst Mode Photo Modes Type-C USB 5V / Batte爀礀...
Need help?
Do you have a question about the T1 and is the answer not in the manual?
Questions and answers