Advertisement
BOH2503D
Fig. 1
A
B
H
C
I
L
F C
M
N
D
O
E
Q
G
F
Fig. 3
G
P
U.K. and IRELAND
PLEASE READ AND SAVE THESE
IMPORTANT INSTRUCTIONS
Fig. 2
When using electrical appliances, basic safety
precautions should always be taken including the
following:
1. Before connecting the heater, check that the
voltage indicated on the rating plate corresponds
to the main voltage in your home/office.
2. WARNING: In order to avoid overheating, do
not cover the heater (
3. DO NOT position the heater directly under a
J
power socket.
4. DO NOT use this heater in the immediate
K
surroundings of a bath, a shower or a
swimming pool.
5. If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its service
agent or similarly qualified person in order to
avoid hazard. The heater contains no user
serviceable parts. Should the product suffer
damage or breakdown, it must be returned to
the manufacturer or their service agent.
6. Under the environment with electrical fast
transient, the product may malfunction.
F C
7. DO NOT use this heater with a programmer,
timer or any other device that switches the
heater on automatically, since a fire risk
exist s if the heater is covered or positioned
incorrectly.
8. Only touch the heater with dry hands.
9. DO NOT use this heater outdoors.
10. DO NOT position where it can be touched by
children, especially the very young.
11. Allow a safe area around the heater away from
T
furniture or other objects; at least 50 cm from
the top and sides and 200 cm at the front. The
heater is to be placed at least 3m from water
source.
12. DO NOT use this heater when it is lying on its
side.
13. DO NOT use the heater in rooms with
explosive gas (e.g. petrol) or while using,
oxygen, inflammable glue or solvent (e.g. when
gluing or varnishing parquet floors, PVC etc.)
Q
14. DO NOT insert any objects into the heater.
15. Keep the mains cord at a safe distance from
the main body of the heater.
16. If overheating should occur, the built-in
overheating safety device will switch off the
heater.
R
17. DO NOT place the cord under a rug.
18. The heater cannot be used adjacent to
curtains or combustible material. Curtains or
S
combustible material may be burned if the
heater was installed incorrectly.
19.This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have
been given supervision or instruction concerning
use of the appliance by a person responsible for
their safety. Children should be supervised to
ensure that they do not play with the appliance.
20. This heater is filled with a precise quantity
of special oil. Repairs requiring opening of
the oil container are only to be made by the
manufacturer or his service agent who should
be contacted if there is an oil leak;
21. When scrapping the heater, follow the
regulations concerning the disposal of oil.
DESCRIPTIONS (See Fig. 1, 2 & 3)
) Reference to product.
A. Heated fins
B. Vents
C. Pull down handle
D. Power switch
E. Cord Storage
F. Power cord
G. Front castor assembly
H. Digital display
I. Power light
J. Mode light
K. Timer light
L. Mode button
M. Thermostat/timer button
N. Adjuster buttons
O. °F - °C button
P. Front wing nut
Q. Castor
R. Rear castor assembly
S. Rear wing nut
T. U-bolt
Technical Specifications
BOH2503D: Wattage: 2500W
ASSEMBLY INSTRUCTIONS (See Fig. 3)
Please make sure the heater has not been
plugged into any electricity outlet. Carefully remove
heater from box. Some accessories are packed
internally. Please make sure you have all of the
following accessories prior to throwing away
packaging. 2 Castor assemblies with four castors
(R, G, & Q), and 2 U Bolts with wing nuts (T, P, S).
Note:
This unit is for FLOOR USE ONLY.
1. Turn the heater upside down and you will see
2 U-bolts (T) with wing nuts over the first and
last joint of the heater.
2. Unscrew the wing nuts (S & P) from the
U-bolts (T).
3. Start with the front of the unit and place one
hole of the front castor assembly (G) to the L
shape of the U-bolt (T) and the other hole of
the castor assembly into the other end of the
U-bolt, then screw on the wing nut (P).
4. Repeat step 3 for the rear castor assembly,
using wing nut (N) instead of wing nut (K) and
rear castor assemblies (M).
5. Use your hand to press the four casters (L)
onto the four axis of the two foot plates until
you hear them click into place. Use your hand
2
to turn the castors and if the move smoothly
thermostat/timer button twice. The (
they have been installed properly.
display to indicate that frost guard is activated.
6. After installation of the front and rear castor
USING THE TIMER
assemblies and the castors turn the heater
Programmable timer
the right way up: the heater is now ready
The user can programme the heater to turn
for use.
OFF after a selected period or to come ON at a
NOTE: Make sure when assembling that the
preset time.
castor assemblies with wheels are pointing
Setting the OFF timer
outwards for maximum stability.
1. Select the mode and temperature you want
OPERATING INSTRUCTIONS
the heater to run.
(See Fig. 1&2)
2. Press the thermostat/timer button 3 times.
1. Ensure the power switch (D) is set to the OFF
The OFF timer icon flashes.
(O) position.
3. Using either the (+) or (-) adjuster buttons,
2. Plug in heater.
programme the heater to turn off up to 24
3. Flip the power switch to the ON (-) position. The
hours later, in increments of 1 hour.
power light (I) will illuminate red until the unit is
Example - 9 hours
unplugged.
4. Press the mode button (L) once to activate the
4. After setting the time, the digital display
unit. The mode light (J) will glow green to indicate
will stop flashing to show the timer is
the heater is running. The unit will automatically
activated. The timer will count down until the
start on Setting 3 (High Heat).
predetermined length of time has passed, and
5. Press the mode button until the desired heat
the heater will then automatically switch off.
setting is shown on the digital display (H).
Example - Switch OFF - The time is 1 pm. The heater
BOH2503D: 3=2500W, 2=1300W, 1=1200W,
is running and you require the heater to switch off at
10 pm; therefore, set the time to 9 hours.
=Energy Saving Mode
After using the heater, press the mode button
Setting the ON timer
until the unit is deactivated and the mode light
1. If the heater is on, press the thermostat/timer
turns off, then turn the power switch to the OFF
control button 4 times. The ON timer icon flashes.
position. Unplug the heater from the socket.
2. Using either the (+) or (-) adjuster buttons,
programme the heater to switch on up to 24
SETTING THE THERMOSTAT
hours later, in increments of 1 hour.
1. Set the desired heat setting by pressing the mode
Example - 4 hours
button.
2. Press the thermostat/timer button (M) once to
3. After setting the ON timer, the digital
display will stop flashing to show the timer is
activate thermostat setting. The room temperature
and a thermostat icon flash on the display.
activated. The timer will count down until the
predetermined period has passed, and then the
3. Press the + or - adjuster buttons (N) to select the
heater will automatically switch on.
desired temperature. (Range 12° C - 30° C)
4. The thermostat symbol will stop flashing. The
NOTE: When the ON timer is set, the unit will
thermostat control will now automatically maintain
remember the setting the unit was previously on
the preset temperature level by turning the heater
and activate to this setting after the predetermined
on and off.
period. The heat setting may be changed after
5. To deactivate the thermostat setting, press
setting the timer by pressing the mode button.
the thermostat/timer button continuously until
ENERGY SAVING MODE
the thermostat symbol does not appear on the
To activate, press the mode button until
display.
appears on the display. The heater will operate
NOTE: The Power light will remain lit during
on a cycle – 10 minutes on High (2500W) and
30 minutes on Medium (1300W). When the
operation.
temperature is at or above 85ºF (30ºC), the
NOTE: It is normal for the heater to cycle ON
heater will ignore the 10 minute High setting and
and OFF as it maintains the preset temperature.
operate on Medium for 30 minutes immediately.
FROST GUARD INSTRUCTION
The cycle repeats while in this mode.
When the heater is in frost guard mode, the
DISPLAY PREFERENCES
temperature will be maintained at 5° C; thus the
The default setting on the digital display is
heater will be in the off status unless the room
degrees Celsius (°C). To switch to degrees
temperature is lower than 5° C. If the room
Fahrenheit (°F), press the °F-°C button.
temperature is lower than 5° C, the heater will
NOTE: Unit must be unplugged for it to be fully off.
automatically start working and will keep turning
on & off all the time, maintaining its ambient
TIP OVER PROTECTION
temperature of 5° C. To activate, press the
When the unit is accidentally knocked over, or
mode button to turn the unit on, then press the
tilts on one side at more than a 45° angle; it
3
) icon will
Advertisement
