Advertisement
HEATER SAFETY
CONSUMER SAFETY INFORMATION
PLEASE READ AND SAVE
THESE IMpORTANT
SAFEgUARDS
IMpORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions
to install the proper outlet.
should always be followed to reduce the risk of fire, electric
DO NOT ATTEMPT TO MODIFY THIS PLUg OR
shock, and injury to persons, including the following:
DEFEAT THIS SAFETY FEATURE IN ANY WAY.
1. Read all instructions before using the appliance.
PLEASE READ AND SAVE
2. T o avoid fire or shock hazard, plug the appliance directly into
a 120V AC electrical outlet.
THESE IMpORTANT
3. T he heater is hot when in use. To avoid burns, DO NOT
SAFETY INSTRUCTIONS
let bare skin touch hot surfaces. Use handle when moving
this heater. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least 3
TECHNICAL SpECIFICATIONS
ft (0.9 m) from the front of the heater and keep them away
Amps:
from the sides and rear.
Wattage:
4. D O NOT run cord under carpeting. DO NOT cover cord with
Working Voltage: 120V AC/60 HZ
throw rugs, runners, or the like. Arrange cord away from
Bulb Type:
traffic area and where it will not be tripped over.
Avoid overloading your circuit by not using other high
5. T his heater is not intended for use in bathrooms, laundry
wattage appliances in the same outlet. At 1500 Watts,
areas and similar indoor locations. NEVER locate heater
this unit draws 12.5 Amps.
where it may fall into a bathtub or other water container.
6. E xtreme caution is necessary when any heater is used by,
ASSEMBLY INSTRUCTIONS
or near children or invalids, and whenever the heater is left
Please make sure to check packaging for parts that could
operating and unattended.
be used to operate your heater.
7. A lways unplug the heater when not in use.
This package includes:
8. W hen unplugging, be sure to pull by the plug and not the
1 - Fireplace Heater
cord.
1 - Remote Control
9. D O NOT insert or allow foreign objects to enter any
1 - Stand
ventilation or exhaust opening as this may cause an electric
1 - Wall Mount Hardware Kit
shock or fire, or damage the heater.
Installing Batteries into the Remote:
10. D O NOT operate heater with a damaged cord or plug, or
Before operation, insert 2 "AAA" batteries into the back of
after the heater malfunctions, or has been damaged in any
the remote control:
manner. Return appliance to manufacturer for examination,
electrical or mechanical adjustment, or repair.
• Do not mix old and new batteries
11. A heater has hot and arcing or sparking parts inside. DO
• D o not mix alkaline, standard (carbon-zinc), or
NOT use it in areas where gasoline, paint, or flammable
rechargeable (nickel-cadmium) batteries
liquids are used or stored.
The remote control for this unit has the capability of
12. Use appliance only for intended household use as described
operating all control panel functions. Please note this
in this manual. Any other use not recommended by the
remote will not work through walls.
manufacturer may cause fire, electric shock, or injury to
Bulb Placement:
persons. The use of attachments not recommended or sold
Unwrap the two 25W Candelabra Bulbs from cardboard
by the manufacturer may cause hazards.
insert found at the top of unit and open doors on back of
13. D O NOT use outdoors.
unit with a screwdriver.
14. T o prevent a possible fire, DO NOT block air intakes or
exhaust in any manner. DO NOT use on soft surfaces like a
bed, where openings may become blocked.
15. T o disconnect heater, press the On/Off button, then remove
Mark for
plug from outlet.
Drill
16. A void the use of an extension cord because the extension
cord may overheat and cause a risk of fire. However, if you
have to use an extension cord, the cord should be No.
14AWG minimum size and rated not less than 1875 watts.
17. I f the heater will not operate, see specific instructions under
Auto Safety Shut-off on resetting the heater.
18. D O NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void your
warranty. The inside of the unit contains no user serviceable
parts. All servicing should be performed by qualified
personnel only.
19. D ISCONTINUE USE IF PLUG OR OUTLET IS HOT.
RECOMMEND OUTLET BE REPLACED IF PLUG OR
OUTLET IS HOT TO TOUCH.
pLEASE SAvE THESE
Mark for
INSTRUCTIONS
Drill
Stand Assembly:
For floor use attach the Stand to the Fireplace heater using
THIS APPLIANCE HAS A POLARIZED
the 4 machine screws (provided). Gently lay the unit on the
PLUG (one blade is wider than the other).
floor and attach the Stand to the bottom For wall mount
To reduce the risk of electric shock, this
plug is intended to fit in a polarized outlet
see Wall Mount Instructions below.
only one way. If the plug does not fit fully
in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician
Wall Mount Installation:
This product weighs 25 lbs. Do not install alone.
Mounting Template with instructions is attached below to
make mounting your Fireplace Heater easy.
12.5
• Wall Mount Hardware Kit includes:
1500W/ (+ 5% - 10%)
4 - 1 .5" Phillips head self tapping screws
4 - toggle bolts
(2) 25W max Candelabra Base
2 - mounting brackets
IMPORTANT: Before drilling into any wall ensure no
electrical cables are present in the area.
Max. height of 47" (1.2 m).
Make sure you allow at least 3 feet (1m) of space on
the sides of unit.
2 - Light bulbs
2 - AAA Batteries for Remote
4 - Machine Screws (for stand)
1. Remove stand from main unit, if installed.
2. S ecure the mounting brackets to the wall using the Wall
Mounting Template provided (see below).
3. H ang main body on wall brackets by lifting over the
bracket and sliding down.
4. Use Cord Wrap to hide extra cord.
0 inches
1
2
3
4
Wall Mounting Template
BRacKeT
GUIDe
To mount into wall studs
Included for mounting:
1. Find studs in wall. Studs are typically 16" (40 cm) apart.
4 - 1.5" (38 mm) Phillips
2. C ut Mounting Template on dotted line and tape onto wall so
head self tapping screws
brackets are centered on studs.
4 - toggle bolts
3. U se level to make sure template is level. Using a sharp object
such as an awl, mark hole location.
2 - mounting brackets
4. U sing a Power Driver with Phillips head bit, drive 1.5" (38 mm)
screws through bracket and drywall into wood or metal stud.
IMPORTANT: Before drilling into any wall ensure no
electrical cables are present in the area.
Note:
The mounting hardware included is intended for mounting the heater on 3/8" to 5/8" (10 – 16mm) drywall affixed to wood or metal studs. For your convenience the wall mount
brackets are 16" (40 cm) on center to align with 2 studs. Not all studs will be 16" (40 cm) on center. If you are not able to align with studs, toggle bolts are provided. For other wall types,
please consult a professional or visit your local hardware store to determine which type of hardware is best for your particular wall.
(Back of Heater)
OpERATING INSTRUCTIONS
• T here may be an odor coming from the heater the
first time you use it. This is normal during the break-in
period. Make sure the heater is in a well ventilated area
(Back of Heater)
and continue running it until the smell goes away.
• Y ou may hear a popping or crackling sound as the
heater heats up. This is normal and safe operation.
• T he Fireplace Heater can be operated by using the
remote control (Fig. 1) or the control panel (Fig. 2)
located on the top of the unit.
(Front of Heater)
• P lace the heater on a firm, level surface or mount on
wall.
• A void overloading your circuit by not using other high
wattage appliances in the same outlet. At 1500 Watts,
(Front of Heater)
this unit draws 12.5 Amps.
Power On/Off
Turn Power ON. LCD and Power Light will illuminate. The
units default settings are: Temperature 80°; Timer OFF;
(Back of Heater)
Flame Brightness HIGH; Sound ON.
Thermostat
• P ress Thermostat button until desired temperature level
appears on LCD Display. It is recommended to start by
(Back of Heater)
setting the temperature to the highest setting. When
your room reaches the desired comfort level, lower the
(Back of Heater)
thermostat until the heat stops and thermostat light
turns off. Note: the fan will continue to run for flame
operation.
(Front of Heater)
• T he system now maintains the selected comfort level
by automatically turning the heater ON and OFF. The
(Back of Heater)
Thermostat light cycles ON and OFF with the heater
element as it maintains the programmed temperature.
• W hen LCD reads 00 the heat will turn off but the fan will
(Front of Heater)
continue to run for flame operation.
Timer
(Front of Heater)
You can set the timer to automatically turn the unit off.
Press the Timer button, select between 1 and 12 hours.
Your selection will then be displayed on the LCD.
Flame Brightness
(Front of Heater)
There are four flame brightness settings: HIGH, MEDIUM,
LOW, OFF. Press button to select desired brightness.
Sound
Press Sound button to adjust 4 sound levels or turn
crackling sound on or off.
Fahrenheit/Celsius
Press to show temperature in Fahrenheit or Celsius.
5
6
7
8
9
To mount into drywall
Use toggle bolts for 3/8 - 5/8" (10 – 16 mm) thick drywall.
1. C ut Mounting Template on dotted line and tape onto wall. Use level to make
sure template is level and mark wall with a sharp object such as an awl.
2. D rill 3/8" (10 mm) holes at top and bottom of bracket guide in center of studs.
3. A - A lign bolts, through bracket holes then thread on Spring Loaded Wings.
B - C ollapse Wings while pushing through hole in wall.
C - P ull bolt out to secure Toggle Wings against inside of wall (wings spring
open on other side of wall and securely hold bolt and bracket).
D - Screw bolt in until tight.
Key TO IcONs
On/Off
Thermostat
Timer
Flame Brightness
Sound
Fahrenheit/Celsius
ReMOTe cONTROl
Fig. 1
cONTROl PaNel
Fig. 2
(Back of Heater)
(Front of Heater)
10
11
12
13
14
Bolt
Drilled
Hole
Toggle
Wall
Bracket
Spring
Loaded
Toggle
Wall
opens on
inside of
wall
FRONT
Control
LCD
Power
Panel
Display
Light
Buttons
Glass
Heat
Removable
Panel
Vent
Stand
BacK
Handle
Hanging
Brackets
Light Bulbs
Cord Wrap
15
16
Mark for
Drill
BRacKeT
GUIDe
Mark for
Drill
Advertisement
