Bionaire BASF1415 - MANUAL 2 Instruction Manual page 2

BASF1415 Fig. 1
D E
C
B
Q
A
N
O
BASF1415-I_09MLM1.indd 4-6 BASF1415-I_09MLM1.indd 4-6
PLEASE READ AND SAVE THESE
INSTRUCTIONS
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety
G H T
F precautions should always be taken including
the following:-
• Use the fan only for purposes described in
the instruction manual.
• To protect against electrical shock, do not
immerse the fan, plug or cord in water or
spray with liquids.
• Close supervision is necessary when any
appliance is used by or near children.
• Unplug from the electrical outlet when not in
S
use, when moving the fan from one location
to another, before putting on or taking off
parts and before cleaning.
J
• Avoid contact with any moving parts.
• Do not operate in the presence of explosive
and/or flammable fumes.
• Do not operate fan until fully assembled with
I
all parts properly in place.
• To avoid fire hazard, NEVER place the cord
K
under rugs or any parts near an open flame,
cooking or other heating appliance.
• Ensure that the fan is switched off from the
supply mains before removing the guard.
• Do not operate any appliance with a
L
damaged cord, plug, after the appliance
malfunctions, or has been dropped/damaged
in any manner.
M • The use of attachments not recommended or
sold by the appliance manufacturer may
cause hazards.
• Do not use outdoors.
• Do not let the cord hang over the edge of a
table or counter, or come into contact with
hot surfaces.
• To disconnect from the electrical supply, grip
the plug and pull from the wall outlet. DO
NOT pull on the cord.
• Always use on a dry, level surface.
• Do not operate without the fan grills properly
in place.
• This product is intended for household use
ONLY and not for commercial or industrial
applications.
• If the supply cord or plug is damaged, it must
be replaced by the manufacturer or its
R
service agent or a similarly qualified person
in order to avoid hazard.
P
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
ENGLISH
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children should be supervised to ensure that
they do not play with the appliance.
MISSING A PART FOR YOUR FAN?
Please call 0800 052 3615 for assistance.
ASSEMBLY INSTRUCTIONS (See Fig 1.)
Base/Pole assembly
You will need the base cover (N), weight (O),
pole (K,M), washer (R) and L-shaped locking
lever (P).
1. Turn the base cover upside down and place
the weight into the base cover.
2. Insert the threaded end of the L-shaped
locking lever into the hole of the washer,
weight and through the base cover.
3. Whilst holding the base cover and weight with
one hand, connect the pole to the base,
sliding the L-shaped locking lever into the
bottom of the pole (M) with your other hand.
4. Turn the L-shaped locking lever clockwise to
securely attach the pole to the base.
5. Set the base on the floor, weight side down.
Fan head assembly
You are now ready to assemble the fan head.
1. Unscrew rear grill mounting nut (D) before
positioning the rear grill (F) over the motor
shaft (G) making certain that the notches at
the top and bottom of the rear grill, fit over
the prongs on the motor housing (H).
2. Secure the rear grill in its place using the
rear grill mounting nut (D). Turn this nut
clockwise and tighten firmly.
3. Slide the fan blade (B) with the hollowed
interior of the blade facing toward the rear
grill, firmly onto the motor shaft. The top of
the motor shaft should lie even with the
centre of the fan blade.
4. Now use the securing screw (C) (already
attached to the Fan Blade) to lock the blade
into place. Tighten the screw into the side
hole of the fan blade, against the motor
shaft, until both the blade and screw are
secure.
5. Centre the front grill (A) by aligning the
Bionaire logo on the logo plate so that it is
horizontal and parallel with the floor. Then,
holding the front grill against the rear grill,
push the black grill ring (E) into place at the
top and bottom of the fan. (Push directly on
the black grill ring, not on the grills
themselves). Finish securing the grill ring in
the same manner until both grills are joined
underneath the black ring.
2
Final assembly CLEANING AND MAINTENANCE
1. Slide the inner pole extension (K) up from Follow these instructions to correctly and safely
the outer pole (M). Insert the pole locking care for your Bionaire
knob (L) into the hole on the outer pole, to
• Always unplug the fan before cleaning or
securely hold this position.
assembly.
2. Place the fan head assembly into this
• Do not allow water to drip on or into the fan
extension pole, inserting the neck of the fan
motor housing.
into the pole opening. Turn the fan head's
• Be sure to use a soft cloth, moistened with a
neck until the head is securely locked into
mild soap solution.
place.
• Do not use any of the following as a cleaner:
3. Add the tilt adjustment knob (J) to the hole in
petrol, thinners or benzene.
the fan head's neck (I). Tighten when the fan
Fan Blade cleaning
head is in your desired position.
(See instructions for fan head assembly)
Converting to a table fan -
1. To access the fan blade, remove the front
On model BASF1415 an additional short pole
grill and securing screw.
(Q) is supplied which allows the fan to be
2. Clean the fan blade, front and rear grills with
converted into a table fan. To change to this
a soft moist cloth.
short pole, remove the fan head assembly from
3. Replace the fan blade, tighten screw and
its position on top of the inner pole and unscrew
securely fasten the front grill.
the L-shaped locking lever at the base. Remove
Fan head, base and pole cleaning
the long pole, replace with the short pole and
reassemble as detailed above. Using a soft, moist cloth, with or without a mild
soap solution, carefully clean the fan base, pole
OPERATING INSTRUCTIONS
and head. Please use caution around the motor
1. Set the fan base on a dry level surface
housing area. Do not allow the motor or other
2. Make sure the Selector (Speed) Control (S)
electrical components to be exposed to water.
is in the OFF (0) position. Selector (Speed)
FAN STORAGE
Control (S) is located on the top of the fan
motor housing. Your fan can be stored either partially
disassembled or assembled.
3. Plug the cord into a suitable 220-240V. AC
It is important to keep it in a safe, dry location.
outlet.
• If stored disassembled, we recommend using
4. The SPEED is adjusted by turning the
Selector (Speed) Control (S) to the desired the original (or appropriately sized) box.
setting:- • If stored assembled or partially assembled,
remember to protect the fan head from dust.
0-III-II-I.
5. The OSCILLATION control (T) is located on For U.K. and Ireland only:
the top of the fan motor housing. To start
If the plug is not suitable for the socket outlets in
oscillation, push the control knob down.
your home, it can be removed and replaced by
To stop oscillation, pull the control knob up.
a plug of the correct type. Please refer to
ADJUSTMENT
"Installation of a plug" below.
Installation of a plug Applicable to
Tilt adjustment
U.K. and Ireland
Follow these instructions to tilt the fan head for
upward angle air movement.
1. To change the tilting angle of the fan head,
simply loosen the tilt adjustment knob (J)
2. Move the fan head to the desired angle, then
firmly tighten the knob to lock in place.
Height adjustment
Follow these instructions to adjust the height of
the fan.
1. Turn the pole locking knob (L) anti-clockwise
to loosen the pole.
NOTE: If the terminals in the plug are not
2. Adjust the pole to the desired height and
marked or if you are unsure or in doubt about
firmly tighten the locking knob in a clockwise the installation of the plug please contact a
direction.
qualified electrician.
3
TM fan. Please remember:-
6/18/09 11:00:08 AM 6/18/09 11:00:08 AM