Advertisement
860678721
Revision C December 2024
commscope.com
SYSTIMAX
General
The SYSTIMAX VisiPORT controller units communicate with each other using the controller LAN. Modular
patch cords can be used to make the controller LAN connections. The panel bus allows the VisiPORT
controller and intelligent panels to communicate. Also, the VisiPORT controller supplies power to the
intelligent panels through the panel bus assembly. An additional backup power supply is available and a
connection for it is provided on the controller. A Rack Extender Kit, sold separately, provides panel buses
and jumpers to enable a VisiPORT controller to manage two dependent racks in addition to the controller's
rack.
Ordering Information is listed below:
Material ID
Part No.
760258085
VisiP-CNTRL
VisiP-CNTRL- AR
760258086
How to Contact Us
To find out more about CommScope products, visit us on the web at
•
For technical assistance, customer service, or to report any missing/damaged parts, visit us at
http://www.commscope.com/SupportCenter
Tools Required
Phillips head screwdriver #2
•
For RoHS Inquiries:
CommScope Inc.
Corke Abbey, Bray
Co. Dublin, Ireland
Attn: Legal Department
VisiPORT™ Controller Installation
®
Description
VisiPORT controller
VisiPORT controller
(Argentina version)
© 2024 CommScope, Inc.
All rights reserved
Instruction Sheet
http://www.commscope.com/
Recycling information can be obtained from the
WEEE recycling section at www.CommScope.com
Page 1 of 11
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CommScope SYSTIMAX VisiPORT VisiP-CNTRL
Summary of Contents for CommScope SYSTIMAX VisiPORT VisiP-CNTRL
- Page 1 VisiPORT controller VisiP-CNTRL- AR 760258086 (Argentina version) How to Contact Us To find out more about CommScope products, visit us on the web at http://www.commscope.com/ • For technical assistance, customer service, or to report any missing/damaged parts, visit us at http://www.commscope.com/SupportCenter...
-
Page 2: Specifications
• Follow all warnings and instructions marked on this product. This product should be operated using only the power supply provided by CommScope with the product. • Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring. -
Page 3: Important: Limitations
860678721 www.commscope.com SYSTIMAX VisiPORT Controller • To reduce the risk of an electrical shock, do not disassemble this product. Service should be performed by trained personnel only. Opening or removing covers and/or circuit boards may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electrical shock when the unit is subsequently used. - Page 4 860678721 www.commscope.com SYSTIMAX VisiPORT Controller Step 1 – Mount Panel Bus Assembly Front Front of rack of rack Vertical cable Panel manager sections Panel bus sections Panel Bus Mounting Panel Bus Mounting on Side on Rear Flange of Rack of Vertical Cable Manager...
- Page 5 860678721 www.commscope.com SYSTIMAX VisiPORT Controller Step 2 – Install Controller on Rack 1. Remove bezel from front of panel by pulling on the left and right side of the bezel. The bezel will pop off the metal base. 2. Using the four provided screws with star washers, install controller panel on rack. Snap the bezel onto the panel.
- Page 6 860678721 www.commscope.com SYSTIMAX VisiPORT Controller Step 3 – Connect Panel Bus Jumper and USB Cable 1. Unfold pre-connected panel bus jumper from under controller and insert female 10-pin connector into the middle panel bus port on panel bus assembly. 2. Install spare port built into jumper cordage into panel bus frame by turning it at an angle, inserting into frame, and turning it back perpendicular to frame.
- Page 7 860678721 www.commscope.com SYSTIMAX VisiPORT Controller 3a) Support for up to three adjacent racks Note: 1. Only adjacent racks are supported for this configuration. 2. Use only components provided in the Rack Extender kit. 1) Use panel bus from Rack Extender Kit to mount it on the rack to the left and/or right of the rack with the VisiPORT controller installed in it.
- Page 8 860678721 www.commscope.com SYSTIMAX VisiPORT Controller Step 4 – Connect Power Supply 1. Connect the power supply barrel connector into PWR1 port on the rear of the controller as shown and loop cord into the provided strain relief on the side of controller.
- Page 9 860678721 www.commscope.com SYSTIMAX VisiPORT Controller Step 6 – Grounding 1. As shipped: The 18 AWG ground wire is preconnected to the Controller base and mounting panel. 2. Optional method: if desired, the ground wire can be disconnected from the mounting panel and then attached to an appropriate ground system within a rack or cabinet.
- Page 10 860678721 www.commscope.com SYSTIMAX VisiPORT Controller Step 7 – Power Up VisiPORT controller 4. Modify the power adapter for use with the local configuration for electrical service outlets: Select the appropriate AC plug. • Insert the tabbed edge of the AC plug into the top of the opening in the power adapter. Then press on the plug until it snaps into place.
-
Page 11: Open Source Software
Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. CommScope is committed to the highest standards of business integrity and environmental sustainability, with a number of CommScope’s facilities across the globe certified in accordance with international standards, including ISO 9001, TL 9000, and ISO 14001.
Need help?
Do you have a question about the SYSTIMAX VisiPORT VisiP-CNTRL and is the answer not in the manual?
Questions and answers