Advertisement
860632997
Revision E December 2024
commscope.com
SYSTIMAX
General
®
The SYSTIMAX
imVision
Modular patch cords can be used to make the controller LAN connections. The panel bus allows the
imVision Controller X and iPatch
power to the iPatch panels through the panel bus assembly. An additional backup power supply is
available and a connection for it is provided on the controller. A Rack Extender Kit, sold separately,
provides panel buses and jumpers to enable an imVision Controller X to manage two dependent racks in
addition to the controller's rack.
This instruction sheet is available online in other languages. Instruction sheets in other languages can be
found by searching for "760237876" from www.commscope.com, then looking at the product page for
760237876 (imVision Controller X)
Ordering Information is listed below:
Material ID
Part No.
760237876
IMV-CNTRL-X
IMV-CNTRL-X-AR
760237877
How to Contact Us
•
To find out more about CommScope
For technical assistance, customer service, or to report any missing/damaged parts, visit us at
http://www.commscope.com/SupportCenter
Tools Required
•
Phillips head screwdriver #2
For RoHS Inquiries:
CommScope Inc.
Corke Abbey, Bray
Co. Dublin, Ireland
Attn: Legal Department
®
®
imVision
®
Controller X units communicate with each other using the controller LAN.
®
panels to communicate. Also, the imVision Controller X supplies
Description
imVision Controller X
imVision Controller X
(Argentina version)
®
products, visit us on the web at
© 2024 CommScope, Inc.
All rights reserved
Controller X Installation
http://www.commscope.com/
Recycling information can be obtained from the
WEEE recycling section at www.CommScope.com
Instruction Sheet
Page 1 of 11
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for CommScope SYSTIMAX imVision Controller X
Summary of Contents for CommScope SYSTIMAX imVision Controller X
- Page 1 This instruction sheet is available online in other languages. Instruction sheets in other languages can be found by searching for “760237876” from www.commscope.com, then looking at the product page for 760237876 (imVision Controller X) Ordering Information is listed below: Material ID Part No.
-
Page 2: Specifications
Follow all warnings and instructions marked on this product. • This product should be operated using only the power supply provided by CommScope with the product. Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on over current protection and supply wiring. -
Page 3: Important: Limitations
860632997 www.commscope.com ® SYSTIMAX imVision • To reduce the risk of an electrical shock, do not disassemble this product. Service should be performed by trained personnel only. Opening or removing covers and/or circuit boards may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electrical shock when the unit is subsequently used. - Page 4 860632997 www.commscope.com ® ® SYSTIMAX imVision Controller X Step 1 – Mount Panel Bus Assembly Front Front of rack of rack Vertical cable Panel manager sections Panel bus sections Panel Bus Mounting Panel Bus Mounting on Side on Rear Flange of Rack...
-
Page 5: Adjustment Of Display Unit
860632997 www.commscope.com ® SYSTIMAX imVision Step 2 – Install Controller on Rack 12-24 mounting screws with star washers (4 places) Bezel detached from panel and hanging on cable management bars Note: imVision Controller X is pre-assembled with cable management bars in holes closest to the front. - Page 6 860632997 www.commscope.com ® ® SYSTIMAX imVision Controller X Step 3 – Connect Panel Bus Jumper and USB Cable 1. Unfold pre-connected panel bus jumper from under controller and insert female 10-pin connector into the middle panel bus port on panel bus assembly.
- Page 7 860632997 www.commscope.com ® SYSTIMAX imVision 3a) Support for up to three adjacent racks Note: 1. Only adjacent racks are supported for this configuration 2. Use only components provided in the Rack Extender kit 1) Use panel bus from Rack Extender Kit to mount it on the rack to the left and/or right of the rack with the imVision Controller X installed in it.
-
Page 8: Step 4 - Connect Power Supply
860632997 www.commscope.com ® ® SYSTIMAX imVision Controller X Step 4 – Connect Power Supply Strain relief 1. Connect the power supply barrel connector into PWR1 port on the rear of the controller as shown and loop cord into the provided strain relief on the side of controller. - Page 9 860632997 www.commscope.com ® SYSTIMAX imVision Step 6 – Grounding 1. As shipped: The 18 AWG ground wire is preconnected to the Controller base and mounting panel. 2. Optional method: if desired, the ground wire can be disconnected from the mounting panel and then attached to an appropriate ground system within a rack or cabinet.
- Page 10 2. Plug the power adapter into an electrical service outlet. 3. Power up imVision Controller X and configure settings and panels per the System Manager User Guide. Please go to the CommScope eCatalog to download the SYSTIMAX imVision System Manager User Guide for features and settings. Included AC plugs:...
-
Page 11: Open Source Software
Inc. This document is for planning purposes only and is not intended to modify or supplement any specifications or warranties relating to CommScope products or services. CommScope is committed to the highest standards of business integrity and environmental sustainability, with a number of CommScope’s facilities across the globe certified in accordance with international standards, including ISO 9001, TL 9000, and ISO 14001.
Need help?
Do you have a question about the SYSTIMAX imVision Controller X and is the answer not in the manual?
Questions and answers