Page 1
HD MULTI PURPOSE CAMERA HDC-X300/X300K HDC-X310/X310K FILTER SERVO UNIT HKC-SV1 MAINTENANCE MANUAL 1st Edition (Revised 1) Serial No. 10001 and Higher: HDC-X300/X300K Serial No. 10001 and Higher: HDC-X310/X310K...
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. HDC-X300...
Page 3
LASER KLASSE 1 PRODUKT verbunden werden, damit sich bei einer Funktionsstörung die Stromversorgung zum Gerät LUOKAN 1 LASERLAITE ß jederzeit unterbrechen lä KLASS 1 LASER APPARAT This HD Camera Interface Unit is classified as a CLASS 1 LASER PRODUCT. 1 (P) HDC-X300...
2-16. Replacing Optical Module (HDC-X310/X310K) .. 2-26 (E) 2. Service Overview 3. SERVICE Menu 2-1. Location and Function of Boards ......2-1 (E) 2-1-1. HDC-X300/X300K ........2-1 (E) 3-1. Menu List ..............3-1 (E) 2-1-2. HDC-X310/X310K ........2-2 (E) 3-2.
Manual Structure Purpose of this manual This manual is the maintenance manual for HD Multi Purpose Camera HDC-X300/ X300K. This manual is intended for use by the trained system enginneers and service enginneers, and describes information (installation overview, service overview, menu and file, electrical alignment, parts lists, block diagrams, schematic diagrams and board layouts) on the premise of component level service.
Block Diagrams Contains the block diagrams of overall and each circuit board. Section 8 Schematic Diagrams Contains schematic diagrams for every circuit board and frame wiring. Section 9 Board Layouts Contains board layouts for every circuit board. 4 (E) HDC-X300...
1-1-2. Recommended Power Cord 1-1-1. Power Supply This unit does not come with a power cord. To get a power cord, please contact your local Sony Sales The supplied AC adaptor is used for the power supply of Office/Service Center.
Analog HD (3-level sync) or SD (2- level sync) sync 1-2-1. Connector Input/Output Signals signal input 2 TRIGGER IN/OUT: BNC type Rear Panel (HDC-X300/X300K) When the camera is in Still mode: This connector functions as the still-picture trigger input (While this connector is on the ground level, the camera output still pictures.)
Page 11
SERIAL DATA IN RX RCP DATA (Y) VIDEO OUT (G) GND for VIDEO OUT (External view) +12 V UNREG OUT UNREG GND GND for UNREG VIDEO OUT (X) 1.0 V p-p, 75 Z Shield CHASSIS GND CHASSIS GND 1-3 (E) HDC-X300...
(8P, FEMALE) CCA cable assembly (optional) CCA-5-30 (30 m) CCA-5-10 (10 m) CCA-5-3 (3 m) HDSDI OUT 1-569-370-12 PLUG, BNC or (HDC-X300/X300K) Coaxial cable BELDEN 1694A or equivalent VIDEO OUT Monitor cable (D SUB-BNC) (commercial cable) TALLY OUT Stereo miniplug...
Section 2 Service Overview 2-1. Location and Function of Boards 2-1-1. HDC-X300/X300K Name Circuit Function AT-159 CPU Board CN-2550 Connectors Board (REMOTE, VIDEO OUT) CN-2566 TALLY Connector Board CN-2691 DC IN Connector Board DIF-154 Digital Interface DIF-155 Digital Interface DPR-253...
Each RGB video signal output differentially from each PA Y10bit, PrPb10bit, HD, VD, and FLD) is directly sent to board is input to the VA IC (IC100, 200, 300). The signal the DIF-154 board. is mixed with the black shading compensation signal at the 2-4 (E) HDC-X300...
Page 17
SAV and the EAV at IC80 to be the SMPTE274M-compliant parallel digital signal. The resultant signal then receives parallel signal conversion at IC5, and is driven as an HDSDI signal at IC8 to be output. 2-5 (E) HDC-X300...
Page 18
The 3-pin regulator IC1 supplies +5 V power supply to the tool for writing programs to the CPU on the DR-567 board. 2-6 (E) HDC-X300...
ON, the FRAM data is entirely Screws with toothed washer reset to the default data. +B (M3 x 8) Factory setting: OFF Top chassis assembly 4. Reinstall the disassembled parts in the reverse order of steps 1 to 3. 2-8 (E) HDC-X300...
Page 21
. “(A-1)” below shows the S50 address (location) on the S50-1 to 4 (A-3): Factory use board. Factory setting: OFF S51-1 to 8 (B-3): Factory use S50-1 to 8 (A-1): Factory use Factory setting: OFF Factory setting: OFF 2-9 (E) HDC-X300...
Model name Oscilloscope Tektronix TDS3054B or equivalent (150 MHz or more) HD analog Waveform monitor Tektronix 1735HD or equivalent Frequency counter Advantest TR5821AK or equivalent HD Color monitor Sony HDM-D20F1 or equivalent Luminance meter Minolta LS-110 or equivalent 2-10 (E) HDC-X300...
CCD block specific data This EEPROM cannot be replaced because the data cannot be re-set. If you want to replace EEPROM with a new IC due to a defective part, contact your local Sony Sales Office/Service Center. 2-11 (E) HDC-X300...
155. *2: IC4/ OPM-48 is the configuration memories for IC1/OPM-49. Equipment required . PLD download fixture (Sony part number: J-7120-140-A) : The cable connected PC to this unit. When connecting the fixture to the board, remove the fixture cable from the fixture itself.
6. Turn on the power of the unit. 1. Write the latest HDC-X300 MS jig program in the two 7. The ROMs on the AT-159 board start writing the latest ROMs on the MS-69 board.
B750 1. Turn off the power of the unit. This section describes the upgrading procedure of the AT- 2. Connect RM-B750 to HDC-X300/X300K with the 159 board ROM program (MAIN) using RM-B750. remote control cable. 3. Insert the Memory Stick containing the latest program Equipment/tools required into the Memory Stick compartment on RM-B750.
2-7. Diagnostics 2-7-1. Device Check The HDC-X300/X300K has the self-diagnostics function to check the communication function of the respective devices. Result of the self-diagnostics is displayed on the DEV STATUS page of the DIAGNOSIS menu. Description of DEV STATUS page (DIAGNOSIS menu) If “NG”...
2-8. Inspection and Maintenance 2-8-1. Recommended Replacement Parts The recommended replacement parts and their recommended replacement timings are. Part name Sony part No. Recommended replacement timing Filter unit, optical 1-788-111-11 It can become nebulous (intransparent and whitened) with elapse of time. Then it will not satisfy the required characteristics.
Press the ENTER button. A question mark flashes at the selected item. 6. Press the ENTER button. The accumulated time of the Fan filter selected hours meter is reset. To quit Menu mode 1. Press the MENU button. Rear chassis 2-17 (E) HDC-X300...
No action is required for boards other than the 2. Standardization of Parts following. Some repair parts supplied by Sony differ from those AT-159 board used for the unit. These are because of parts common- 1. Upgrade the FLASH MEMORY (IC8, IC9) ality and improvement.
Aplicable Model Type of CCD Bock connecting the flexible card wire. HDC-X300 HDC-X300K Disconnecting 1. Turn off the power. 2. Slide or lift the portion A in the arrow direction to unlock and pull out the flexible card wire.
2-12. Removing/Reinstalling the Fan the Coaxial Cable . Replace the DC fan on the basis of “30,000 hours” Coaxial cables are used in HDC-X300/X300K. reading of the hours meter (FAN). . After the DC fan is replaced, reset the hours meter The following notes are required for disconnecting/ connecting the coaxial cables.
Page 33
DC fan Fan cushion Rear chassis assembly Fan filter MB-1042 board CN203 CN4 CN202 Screws with Rear chassis toothed washer +B (M3 x 8) Flexible card wire <Top view> 2-21 (E) HDC-X300...
Page 34
DC fan VA-221 board Coaxial cable Fan filter Fan cushion Notch Coaxial connector Board holder Rear chassis 9. Reset the hours meter (FAN) using the SERVICE menu “HOURS METER” page 2 only when the DC fan is replaced. 2-22 (E) HDC-X300...
Be very careful not to fold the flexible card wires. Its life will be significantly shortened if it is folded. Setscrew (WP3 x 3) AT-159 board Board holder Filter knob Boundary of color DPR-253 board Flexible card wire Flexible card wires 2-23 (E) HDC-X300...
Page 36
Filter ring Screws Front chassis assembly M3 x 8 Lens mount holder MB-1042 board CCD block assembly Screws with Filter konb toothed washer Front chassis assembly +B (M3 x 8) Screws Setscrew M3 x 8 (WP3 x 3) 2-24 (E) HDC-X300...
. Install the board holder taking care of its orientation and remove the board holder, OPM-48 board, and and position. OPM-49 board. Board horder VA-221 board Coaxial cable OPM-48 board OPM-49 board Notch Coaxial connector Board holder 2-25 (E) HDC-X300...
OPM-49 board OPM-48 board Fiber end with LC connector Installation Lock release lever (Press the lever to release the lock.) Install the removed parts by reversing steps 1 to 4 above. Fiber end with LC pair connector 2-26 (E) HDC-X300...
Page 39
Section 2-7.) Then insert the LC connector of the optical fiber cable until the LC connector locks with a clicking sound. Check that the OFC connector marked with ## is connected to the connector with the same mark on the optical module. 2-27 (E) HDC-X300...
VCO FREQ. 60I — FAN (H) — — VCO FREQ. 50I — RESET OPR — — 60I VCO SELECT NORM — RESET FAN — — * : When the software of version 1.80 or before is installed: O 3-1 (E) HDC-X300...
This menu enables you to confirm the camera’s status or identify a failed circuit board. SERVICE menu Normally this menu is not displayed. To display this menu, refer to Section 3-2-3 “Displaying the SERVICE menu (Service Mode)”. 3-2 (E) HDC-X300...
M A I N T E N A N C E F I L E D I A G N O S I S Pressing the MENU button for the second or subse- quent time, the previously displayed menu page appears. 3-3 (E) HDC-X300...
ESC on the line below the character list. To register the new string you have set, select END and press the ENTER button. To restore the previous string, select ESC and press the ENTER button. 3-4 (E) HDC-X300...
Refer to “Data Structure” for details of the hierarchical structure. menu item. FACTORY PRESET Press the MENU Returns all the settings to the factory default settings. (Excluding knob to execute this the black balance automatic adjustment value.) menu item. 3-5 (E) HDC-X300...
Page 46
Normal setting when using a lens OFF: Setting for use of a lens with no iris data return (Even if a lens with no iris data return is used, iris overshoot or hunting must not be generated. 3-6 (E) HDC-X300...
Page 47
Adjusts the V.PARA correction. The R, G and B displays are switched in accordance with the channel selection implemented by the above SHADING CH SEL. WHITE SAW/PARA OFF/ON Turns ON/OFF all the white shading menu items of R/G/B, H/V and SAW/PARA corrections. 3-7 (E) HDC-X300...
Page 48
SAW/PARA corrections. MASTER BLACK (_99 to +99) Adjusts the master black level (All of the R, G and B master black levels are adjusted.) MASTER GAIN (TMP) _3/0/3/6/9/12/18/ Temporarily adjusts the master gain value. 24/30/36/42/48 dB 3-8 (E) HDC-X300...
Page 49
DIG: Characters (such as menus) are mixed to the digital output only. Be careful when changing a setting. If the character mix for the current output is set to OFF, the menu operations will be disabled. 3-9 (E) HDC-X300...
Page 50
(_99 to +99) Adjusts the VCO frequency for 50I/25PsF. Set the above SCAN MODE to 50I (or 25PsF). 60I VCO SELECT NORM/60.00 Normally select “NORM”. Select “60.00” only when 60.00I/ 30.00PsF/24.00PsF is selected for 60I/30PsF/24PsF instead of 59.94I/29.97PsF/23.98PsF. 3-10 (E) HDC-X300...
Page 51
(_99 to +99) Adjusts the compensation point level of the G-channel. Adjusts to the peripheral black level. B S/H DC (_99 to +99) Adjusts the compensation point level of the B-channel. Adjusts to the peripheral black level. 3-11 (E) HDC-X300...
Page 52
SENS: Sensitivity measurement mode REGI: Registration measurement mode MASTER BLACK (_99 to +99) Adjusts the master black level. (All of the R, G and B signal black levels are adjusted.) MASTER GAIN (TMP) _3/0/3/6/9/12/18/24/ Sets the tentative gain value. 30/36/42/48 3-12 (E) HDC-X300...
Page 53
Starts to the auto white shading adjustment. knob to execute this menu item. RESET WHT SHD Press the MENU Returns the white shading value to the factory default value. knob to execute this (SAW/PARA or 3D) menu item. 3-13 (E) HDC-X300...
Page 54
Setting the CCD readout mode. (Only for the S12 MANUAL RPN page) FIELD: Field readout (normal readout) FRAME: Frame readout (Use when you want to get higher vertical scan frequency.) When the Super EVS mode is ON, the FIELD is selected forcibly. 3-14 (E) HDC-X300...
Page 55
Resets the OPERATION (power-on time display) mode. knob to display this For resetting, refer to Section 2-8-2. item. RESET FAN Press the MENU Resets the FAN (fan operating time display) mode. knob to display this For resetting, refer to Section 2-8-2. item. 3-15 (E) HDC-X300...
Page 56
Indicates current filter disk angle (only when HKC-SV1 is connected). FILTER POS P/L Display only Indicates filter position. P: Current position L: Position specified by the remote controller (HKC-SV1 Software Display only Indicates FILTER SERVO UNIT software version (only when version) HKC-SV1 is connected). 3-16 (E) HDC-X300...
Page 57
Indicates type and version of the option board inserted in HFU- VERSION X310 when HFU-X310 is connected. SLOT2 BOARD Display only Indicates type and version of the option board inserted in HFU- VERSION X310 when HFU-X310 is connected. 3-17 (E) HDC-X300...
Page 1 FUNCTION 1 YPrPb/ OUTPUT → CAM ITEM: DC IN MASTER GAIN → 0 dB ITEM: LENS supplied HDC-X300/X300K with HDC-X300K HD color monitor MENU: OPERATION or ENG/EFP LENS PAGE: Page 2 FUNCTION 2 SCAN MODE → 60I 75 Z...
Adjust the position and angle of the light source so that the whole surface of the chart is evenly 2000 lx. Light the chart from almost the same direction and height as the camera to shoot the chart. 4-2 (E) HDC-X300...
Page 61
4. Adjust the luminance control of the pattern box so that the white portion in the center of the chart is 573 ± 6 cd/m This corresponds to the luminous intensity on the 89.9 %-reflective chart at 2000 lx. Chart Luminance meter 4-3 (E) HDC-X300...
COLOR FINE <A> → 0 ITEM: R GAIN <A> → 0 ITEM: B GAIN <A> → 0 ITEM: 2. Adjust auto-black balance (Set the menu to OFF using the MENU button on the side panel, and press the DOWN/BLACK button.) 4-5 (E) HDC-X300...
2. Manual black shading adjustment When finer adjustment or manual adjustment is required, proceed as follows. (1) On the menu, set as follows. MENU: SERVICE PAGE: Page 4 BLACK SHADING BLK SHAD CH SEL → G (Adjustment ITEM: channel) 4-6 (E) HDC-X300...
. Iris of the lens: A = 600 ± 20 mV (at F4 to F5.6) (If a lens aperture is greater than F5.6, adjust the light amounts with shutter.) . Lens Focus: ∞ . Lens Extender/Shrinker: x2, x0.8 → OFF 4-7 (E) HDC-X300...
A. A = 700 ± 20 mV MENU: SERVICE PAGE: Page 3 WHT SHADING WHT SHAD CH SEL → B (Adjust- ITEM: ment channel) (6) Adjust the B-channel in the same procedure as the G-channel adjustment. 4-8 (E) HDC-X300...
SHUTTER switch (Front panel) → SLS: 2 FRAME or more . On the menu, set as follows. MENU: SERVICE PAGE: MANUAL RPN (Standard adjustment) PAGE: MANUAL RPN (SLS) (For the RPN adjust- ment that appears only in slow shutter mode.) 4-9 (E) HDC-X300...
ITEM: To cancel the RPN correction after the correction is completed, perform the Cancel without moving the position of the cross cursor. DELETE RPN → EXEC ITEM: 5. To correction another RPN, repeat steps 2 to 4. 4-10 (E) HDC-X300...
3-364-990-01 s SCREW (M3X8) 3-626-792-01 o RING,MOUNT(D) 3-701-505-00 s SET-SCREW,HEX 3X3 ST 3-710-054-01 s KNOB,FILTER 3-724-455-61 s SCREW +P M2X5 (EP-FE/CU,NI,CR) 3-729-076-11 s SCREW +B2X4 (STEEL) 3-796-982-02 s HOLDER LENS MOUNT 3-965-077-01 s SCREW, SPECIAL (M2) 7-627-551-78 s SCREW,PRECISION +P 1.4X4 HDC-X300...
3-687-116-01 o WASHER(4),STOPPER (PLA) A-1052-804-A s MOUNTED CIRCUIT BOARD, LED-421 3-174-664-02 s SCREW, TRIPOD 3-178-214-11 s SCREW +B (M3X8) 3-364-941-01 s SCREW (+B) (2.6X5),NYLOK 7-627-454-37 s SCREW, PRECISION +K2.6X5 7-627-553-47 s SCREW, PRECISION +P2X4 7-682-565-04 s SCREW +B4X16(EP-FE/CU,NI,CR) 7-685-132-19 s SCREW +PTP2.6X5 HDC-X300...
Page 71
Rear Block (HDC-X300/X300K) Part No. SP Description A-1052-800-A s MOUNTED CIRCUIT BOARD, CN-2550 A-1052-805-A s MOUNTED CIRCUIT BOARD, PSW-83 A-1073-964-A s MOUNTED CIRCUIT BOARD, CN-2691 1-698-741-31 s FAN, DC (WITH 40 MM ALARM) 1-829-884-11 s CABLE ASSY, COAXIAL 3-178-214-11 s SCREW +B (M3X8) 3-364-941-01 s SCREW (+B) (2.6X5),NYLOK...
Page 72
A-1052-805-A s MOUNTED CIRCUIT BOARD, PSW-83 A-1073-964-A s MOUNTED CIRCUIT BOARD, CN-2691 1-698-741-31 s FAN, DC (WITH 40 MM ALARM) 1-797-238-11 s MODULE, OPTICAL (SFP) 3-178-214-11 s SCREW +B (M3X8) 3-364-941-01 s SCREW (+B) (2.6X5),NYLOK 3-669-607-22 s +PSW 2.6 HDC-X300...
Page 73
DIF/RE Block (HDC-X300/X300K) B2.6 x 3 Part No. SP Description A-1052-796-A s MOUNTED CIRCUIT BOARD, MB-1042 A-1053-687-A s RE ASSY A-1053-688-A s DIF ASSY A-1057-707-A s MOUNTED CIRCUIT BOARD, DPR-253 A-1057-708-A s MOUNTED CIRCUIT BOARD, SS-99 A-1057-711-A s MOUNTED CIRCUIT BOARD, AT-159 3-174-664-02 s SCREW, TRIPOD 3-364-941-01 s SCREW (+B) (2.6X5),NYLOK...
Page 74
A-1057-711-A s MOUNTED CIRCUIT BOARD, AT-159 A-1112-943-A s MOUNTED CIRCUIT BOARD, OPM-48 A-1112-945-A s MOUNTED CIRCUIT BOARD, OPM-49 3-174-664-02 s SCREW, TRIPOD 3-364-941-01 s SCREW (+B) (2.6X5),NYLOK K2.6 x 5 7-621-775-08 s SCREW +B2.6X3 7-627-454-37 s SCREW, PRECISION +K2.6X5 HDC-X300...
Page 75
7-621-734-09 s SET-SCREW,HEX 2.6X3 (WP) ST 7-621-775-68 s SCREW +B 2.6X12 7-624-106-04 s STOP RING, TYPE-E3 7-627-454-37 s SCREW +K2.6X5 7-627-553-37 s SCREW,PRECISION +P 2X3 7-628-253-20 s SCREW +PS 2X6 7-628-254-00 s SCREW +PS 2.6X5 7-682-261-04 s SCREW +K 4X8 HDC-X300...
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C318 1-115-339-11 s CAPACITOR,CERAMIC 0.1MF/50V C319 1-107-417-11 s CAPACITOR ERECT 33MF/25V(105C) 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C320 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216 1-127-573-11 s CAPACITOR,CERAMIC 1MFB(2012) C321 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V HDC-X300...
Page 77
1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) IC205 8-759-598-44 s IC TC7WH08FK(TE85R) IC206 8-759-598-44 s IC TC7WH08FK(TE85R) 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) IC207 8-752-392-03 s IC CXD1095BR 1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) HDC-X300...
Page 78
1-208-935-11 s RESISTOR, CHIP 100K (1005) R206 1-208-927-11 s RESISTOR, CHIP 47K 1/16W(1005) 1-208-935-11 s RESISTOR, CHIP 100K (1005) R207 1-208-935-11 s RESISTOR, CHIP 100K (1005) 1-208-935-11 s RESISTOR, CHIP 100K (1005) R208 1-208-935-11 s RESISTOR, CHIP 100K (1005) 5-10 HDC-X300...
Page 79
1-208-675-11 s RESISTOR CHIP 470 1/16W (1005) 1-234-381-21 s RES, NETWORK 100KX4 (1005) R323 1-208-691-11 s RESISTOR CHIP 2.2K 1/16W(1005) 1-234-381-21 s RES, NETWORK 100KX4 (1005) R324 1-208-699-11 s RESISTOR,CHIP 4.7K 1/16W(1005) 1-234-381-21 s RES, NETWORK 100KX4 (1005) 5-11 HDC-X300...
Page 80
1-469-092-11 s INDUCTOR, MICRO (CHIP TYPE) FB12 1-469-092-11 s INDUCTOR, MICRO (CHIP TYPE) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 1-216-864-11 s CONDUCTOR, CHIP (1608) 5-12 HDC-X300...
Page 81
------------------------------ DIF-154 BOARD (HDC-X300/X300K) (DIF-154 BOARD (HDC-X300/X300K)) ------------------------------ Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description A-1053-688-A s DIF ASSY IC54 8-759-472-43 s IC 74VHC245MTCX (This assembly includes the DIF-155 mounted circuit...
Page 82
------------------------------ (DIF-154 BOARD (HDC-X300/X300K)) DIF-155 BOARD (HDC-X300/X300K) ------------------------------ Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description 1-208-711-11 s RESISTOR CHIP 15K 1/16W (1005) A-1053-688-A s DIF ASSY 1-208-695-11 s RESISTOR CHIP 3.3K 1/16W(1005) (This assembly includes the DIF-154 mounted circuit 1-208-691-11 s RESISTOR CHIP 2.2K 1/16W(1005)
Page 83
(DIF-155 BOARD (HDC-X300/X300K)) (DIF-155 BOARD (HDC-X300/X300K)) Ref. No. Ref. No. or Q'ty Part No. SP Description or Q'ty Part No. SP Description 1-100-421-21 s CAP, ELECT 220MF (6.3X5.9) 1-412-056-11 s INDUCTOR 4.7UH (3225) 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 1-412-056-11 s INDUCTOR 4.7UH (3225) 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V...
Page 85
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C224 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C800 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C225 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C801 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C226 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C802 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 5-17 HDC-X300...
Page 86
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C936 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V IC405 8-759-392-77 s IC SN74LVC245APW (E20) C937 1-127-956-11 s CAPACITOR,CHIP FILM 0.1MF IC406 8-759-392-77 s IC SN74LVC245APW (E20) C938 1-127-573-11 s CAPACITOR,CERAMIC 1MFB(2012) IC408 8-759-678-06 s IC CAT24WC02JI-TE13 5-18 HDC-X300...
Page 87
8-729-230-27 s TRANSISTOR 2SA1213Y-TE12L 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) Q905 8-729-230-27 s TRANSISTOR 2SA1213Y-TE12L 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) 5-19 HDC-X300...
Page 88
1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) R269 1-208-699-11 s RESISTOR,CHIP 4.7K 1/16W(1005) R211 1-208-691-11 s RESISTOR CHIP 2.2K 1/16W(1005) R270 1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) R212 1-208-691-11 s RESISTOR CHIP 2.2K 1/16W(1005) R271 1-208-860-11 s RESISTOR CHIP 75 1/16W (1005) 5-20 HDC-X300...
Page 89
1-234-372-11 s RES, NETWORK 100X4 (1005) R715 1-208-935-11 s RESISTOR, CHIP 100K (1005) R716 1-208-935-11 s RESISTOR, CHIP 100K (1005) RB202 1-234-372-11 s RES, NETWORK 100X4 (1005) R717 1-208-935-11 s RESISTOR, CHIP 100K (1005) RB203 1-234-372-11 s RES, NETWORK 100X4 (1005) 5-21 HDC-X300...
Page 90
1-234-375-21 s RES, NETWORK 1KX4 (1005) RB512 1-234-375-21 s RES, NETWORK 1KX4 (1005) RB701 1-234-372-11 s RES, NETWORK 100X4 (1005) RB702 1-234-372-11 s RES, NETWORK 100X4 (1005) RB703 1-234-372-11 s RES, NETWORK 100X4 (1005) RB704 1-234-372-11 s RES, NETWORK 100X4 (1005) 5-22 HDC-X300...
Page 91
1-208-715-11 s RESISTOR,CHIP 22K 1/16W (1005) 1-414-404-11 s INDUCTOR (SMD) 100UH 1-208-943-11 s RESISTOR CHIP 220K 1-414-404-11 s INDUCTOR (SMD) 100UH 1-208-943-11 s RESISTOR CHIP 220K 1-208-943-11 s RESISTOR CHIP 220K 8-729-807-51 s TRANSISTOR 2SD1623-S 1-208-911-11 s RESISTOR, CHIP 10K (1005) 5-23 HDC-X300...
Page 92
1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) 1-234-375-21 s RES, NETWORK 1KX4 (1005) 1-234-375-21 s RES, NETWORK 1KX4 (1005) 1-771-248-11 s SWITCH, TACT 1-771-248-11 s SWITCH, TACT 1-692-881-41 s SWITCH, SLIDE 1-771-709-31 s SWITCH, SLIDE 1-795-244-11 s VIBRATOR, CERAMIC 5-24 HDC-X300...
Page 93
8-719-421-67 s DIODE MA132WK 1-165-871-11 s CAPACITOR,ELECT 22MF 1-127-820-11 s CAPACITOR, SQUARE CHIP 4.7MF 6-706-487-01 s IC TC7SH08FU(T5RSOYJF) IC201 8-759-041-46 s IC L78M05TLL-SONY-TL 1-764-093-21 o PIN, CONNECTOR (PC BOARD) 8P IC202 8-759-588-01 s IC LTC1473CGN-E2 1-817-456-21 s CONNECTOR, COAXIAL IC203...
Page 94
1-100-421-21 s CAP, ELECT 220MF (6.3X5.9) 1-165-871-11 s CAPACITOR,ELECT 22MF 1-165-871-11 s CAPACITOR,ELECT 22MF 1-100-421-21 s CAP, ELECT 220MF (6.3X5.9) 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 1-164-943-11 s CAPACITOR,CHIP CERAMIC 0.01MF 5-26 HDC-X300...
Page 95
1-208-935-11 s RESISTOR, CHIP 100K (1005) IC52 8-759-592-44 s IC TC7SZ04FU(TE85R) 1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) IC53 8-759-669-69 s IC TLC7733IPWR-12 1-208-927-11 s RESISTOR, CHIP 47K 1/16W(1005) IC54 8-759-669-75 s IC TLC2932IPWR 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) 5-27 HDC-X300...
Page 96
1-234-378-11 s RES, NETWORK 10KX4 (1005) RB61 1-234-378-11 s RES, NETWORK 10KX4 (1005) RB62 1-234-372-11 s RES, NETWORK 100X4 (1005) 1-692-270-41 s SWITCH, SLIDE 1-692-271-31 s SWITCH, SLIDE 1-813-559-11 s OSCILLATOR, CRYSTAL (VCXO) 1-813-558-11 s OSCILLATOR, CRYSTAL (VCXO) 5-28 HDC-X300...
Page 97
8-729-929-26 s TRANSISTOR DTC114TE 1-115-339-11 s CAPACITOR,CERAMIC 0.1MF/50V 8-729-929-26 s TRANSISTOR DTC114TE 8-729-929-26 s TRANSISTOR DTC114TE 1-135-341-11 s CAPACITOR,SOLID ELECT 330MF 8-729-929-26 s TRANSISTOR DTC114TE 1-131-999-11 s CAPACITOR,SOLID ELECT 150MF 1-135-343-11 s CAPACITOR,SOLID ELECT 120MF 8-729-929-26 s TRANSISTOR DTC114TE 5-29 HDC-X300...
Page 98
1-208-703-11 s RESISTOR,CHIP 6.8K 1/16W(1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) 1-208-703-11 s RESISTOR,CHIP 6.8K 1/16W(1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 5-30 HDC-X300...
Page 99
1-137-757-21 s CAP, ALUMINIUM SOLID ELECT 1-100-627-21 s CAPACITOR, CHIP ELECT10MF6358 1-107-826-11 s CAPACITOR,CHIP CERAMIC 0.1MF 1-115-339-11 s CAPACITOR,CERAMIC 0.1MF/50V 1-115-339-11 s CAPACITOR,CERAMIC 0.1MF/50V 1-135-347-11 s CAP, SOLID ELECT 82MF 1-135-349-11 s CAPACITOR,SOLID ELECT 22MF 20V 1-100-627-21 s CAPACITOR, CHIP ELECT10MF6358 5-31 HDC-X300...
Page 100
8-729-047-85 s TRANSISTOR SI4416DY-T1 8-729-047-85 s TRANSISTOR SI4416DY-T1 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 8-729-047-85 s TRANSISTOR SI4416DY-T1 1-208-935-11 s RESISTOR, CHIP 100K (1005) 8-729-927-99 s TRANSISTOR 2SC4617R 1-218-939-11 s RESISTOR, CHIP 68 1/16W (1005) 5-32 HDC-X300...
Page 101
1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-208-715-11 s RESISTOR,CHIP 22K 1/16W (1005) 1-208-699-11 s RESISTOR,CHIP 4.7K 1/16W(1005) 1-208-699-11 s RESISTOR,CHIP 4.7K 1/16W(1005) R100 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-443-315-11 s TRANSFORMER, DC-DC CONVERTER 1-535-877-22 s CHIP,CHECKER (TEST POINT) 5-33 HDC-X300...
Page 102
1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) 8-759-564-49 s IC TC7W53FU-TE12R 8-759-327-01 s IC NJM062V-TE2 1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) 8-759-980-44 s IC TL712CPS 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) 6-706-487-01 s IC TC7SH08FU(T5RSOYJF) 1-218-941-11 s RESISTOR,CHIP 100 1/16W (1005) 5-34 HDC-X300...
Page 103
1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 1-163-021-91 s CAPACITOR, CERAMIC 0.01MF/50V 1-107-419-11 s CAPACITOR,ELECT 22MF/35V 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V 5-35 HDC-X300...
Page 104
C228 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V IC17 8-759-675-47 s IC SN74LVC04APWR C229 1-115-339-11 s CAPACITOR,CERAMIC 0.1MF/50V C230 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V IC19 8-759-592-48 s IC TC7SZ32FU(TE85R) C231 1-164-874-11 s CAPACITOR,CHIP CERAMIC 100PF IC20 8-759-592-42 s IC TC7SZ00FU(TE85R) 5-36 HDC-X300...
Page 105
1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-208-911-11 s RESISTOR, CHIP 10K (1005) 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) 1-208-683-11 s RESISTOR CHIP 1K 1/16W (1005) 5-37 HDC-X300...
Page 106
1-208-695-11 s RESISTOR CHIP 3.3K 1/16W(1005) R213 1-208-923-11 s RESISTOR, CHIP 33K (1005) R214 1-208-695-11 s RESISTOR CHIP 3.3K 1/16W(1005) R215 1-208-695-11 s RESISTOR CHIP 3.3K 1/16W(1005) R216 1-208-911-11 s RESISTOR, CHIP 10K (1005) R217 1-208-691-11 s RESISTOR CHIP 2.2K 1/16W(1005) 5-38 HDC-X300...
Page 107
1-165-871-11 s CAPACITOR,ELECT 22MF C402 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C101 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C403 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216 C102 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V C404 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 5-39 HDC-X300...
Page 108
1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V IC100 8-752-109-38 s IC CXA3648R-T4 C461 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 C462 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 IC101 8-759-561-46 s IC AD8014ART-REEL7 C463 1-125-777-11 s CAPACITOR CERAMIC 0.1MF/10V IC200 8-752-109-38 s IC CXA3648R-T4 5-40 HDC-X300...
Page 109
1-208-675-11 s RESISTOR CHIP 470 1/16W (1005) 1-208-635-11 s RESISTOR CHIP 10 1/16W (1005) R300 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) R301 1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) 1-208-935-11 s RESISTOR, CHIP 100K (1005) R303 1-218-945-11 s RESISTOR,CHIP 220 1/16W(1005) 5-41 HDC-X300...
Page 110
1-218-990-11 s RESISTOR,CHIP 0 1/16W (1005) R452 1-208-675-11 s RESISTOR CHIP 470 1/16W (1005) R512 1-208-635-11 s RESISTOR CHIP 10 1/16W (1005) R453 1-208-675-11 s RESISTOR CHIP 470 1/16W (1005) R513 1-208-635-11 s RESISTOR CHIP 10 1/16W (1005) 5-42 HDC-X300...
Q'ty Part No. SP Description 1-468-626-91 s ADAPTOR, AC 3-167-517-01 s PLATE, NUMBER (PC) 3-764-889-01 o CHART,ADJUSTMENT 3-854-613-02 s OPERATION MANUAL 3-854-760-02 s CD-ROM(HDC-X300) HKC-SV1 (OPTION) Ref. No. or Q'ty Part No. SP Description 1-757-276-12 s CABLE, FLEXIBLE FLAT (10 CORE) 2pcs 7-621-734-09 s SET-SCREW,HEX 2.6X3 (WP)
In addition, for semiconductors with ID Nos., refer to the separate CD-ROM titled “Semiconductor Pin Assignments” (Sony Part No. 9-968-546-xx) that allows searching for parts by semiconductor type or ID No. The semiconductors in the manual or on the CD-ROM are listed by equivalent types.
DIGITAL PROCESS TRIGGER GAIN UP GAIN UP GAIN UP MASTER CLK TRIGGER SIG.GEN BCS_TX/RX HD,VD ANALOG OUT WHT BAL WHT BAL WHT BAL 12_BIT A/D VIDEO R/Pr D/A CONV. B/Pb 12_BIT A/D VD/SYNC HD D-SUB 12_BIT A/D SDRAM Overall (HDC-X310/X310K) HDC-X300...
Page 120
TG,3-34 1-32 IC10 IC4(1/2),IC5(1/2) G SH OUT(+) RG GEN VA,101-2 G SH OUT(-) VA,101-1 H ENB TG,4-12 G H NEG(56MHz) TG,4-13 LH GEN IC13 G SHD ENB TG,3-49 1-20 G SHD TG,3-38 1-31 CI12 G SHP TG,3-39 1-30 PA-305 HDC-X300...
Page 121
B SH OUT(-) BLACK SET PA304 2-1 201-1 WHITE BAL STEP B VA OUT(X) 8-BIT WHITE SHADING GAIN 2-44 DPR 4-2 4,5,6 42 22 GAIN CON2 B WGAIN B WHT SHAD 3 GAIN SEL 3,4,5 B BLK SHAD VA-221 HDC-X300...
Need help?
Do you have a question about the HDC-X300 and is the answer not in the manual?
Questions and answers