Related Manuals for Doro L10
Summary of Contents for Doro L10
- Page 1 Doro L10 Disassembly and Assembly procedure Doro L10 Disassembly&Assembly procedure 1/16...
-
Page 2: Table Of Contents
4.7 A ................14 SSEMBLE COMPONENTS ON THE UPPER HOUSING 4.8 A ......................15 SSEMBLE THE REAR HOUSING 4.9 A ........................15 SSEMBLE THE SCREW 4.10 A ................. 16 SSEMBLE THE ATTERY AND THE ATTERY COVER Doro L10 Disassembly&Assembly procedure 2/16... -
Page 3: Introduction
Introduction The purpose of this document is to explain how to disassemble and assemble DORO L10 product. Detailed steps are mentioned with warnings as below. Doro L10 Disassembly&Assembly procedure 3/16... -
Page 4: Tooling Definition
Tooling definition Forceps Screwdriver Plastic Card Doro L10 Disassembly&Assembly procedure 4/16... -
Page 5: Disassembling Procedure
Disassembling procedure Remove the battery cover Remove the battery cover by opening the special slot. Remove the battery Remove the battery by opening the special slot. Doro L10 Disassembly&Assembly procedure 5/16... -
Page 6: Remove The Screws
Remove the rear housing by plastic card or plectrum and please start from the bottom of the product and then along the sides to open the rear housing assembly carefully. Remove the PCBA Remove the PCBA from the upper assembly by using forceps carefully. Doro L10 Disassembly&Assembly procedure 6/16... -
Page 7: Remove The Front Housing Assembly
Remove the front housing assembly Remove the rubber keypad from the front housing. Remove the receiver from the front housing. Remove components from the PCBA Remove the rear camera from the PCBA by using the forceps Doro L10 Disassembly&Assembly procedure 7/16... -
Page 8: Remove The Lcd
Remove the SOS FPC from the PCBA by using the forceps. Remove the USB Rubber and the MIC rubber from the PCBA by using the forceps Remove the LCD Remove the LCD FPC from the PCBA by using the forceps. Doro L10 Disassembly&Assembly procedure 8/16... -
Page 9: Remove The Charger Spring Clip Cover And Keypad Film
Remove the LCD from the PCBA by using the forceps Remove the Charger spring clip cover and Keypad film Remove the Keypad film from the PCBA by using the forceps Remove the Charger spring clip from the PCBA. Doro L10 Disassembly&Assembly procedure 9/16... -
Page 10: Remove The Side Key
3.11 Remove the Speaker and motor Remove the speaker from the rear housing by using the forceps. Remove the motor from the rear housing by using the forceps. Doro L10 Disassembly&Assembly procedure 10/16... -
Page 11: Assembling Procedure
Assemble motor to rear housing by using the forceps. Assemble the speaker to the rear housing by using the forceps. Assemble the side key the rear housing by using the forceps. Assemble the side key to Doro L10 Disassembly&Assembly procedure 11/16... -
Page 12: Assemble The Charger Spring Clip Cover And Keypad Film
Assemble the Charger spring clip to the PCBA. Assemble the Keypad film to the PCBA by using the forceps Assemble the LCD Assemble the LCD and the LCD FPC to the PCBA by using the forceps Doro L10 Disassembly&Assembly procedure 12/16... -
Page 13: Assemble Components On The Pcba
Assemble components on the PCBA Assemble the rear camera, SOS FPC, MIC rubber and USB rubber on the PCBA by forceps. Doro L10 Disassembly&Assembly procedure 13/16... -
Page 14: Assemble The Front Housing Assembly
Assemble the front housing assembly Assemble the receiver and keypad on the by forceps front housing Assemble components on the upper housing Assemble the PCBA to the by forceps front housing Doro L10 Disassembly&Assembly procedure 14/16... -
Page 15: Assemble The Rear Housing
Assemble the rear housing Assemble the rear housing to the front housing. Assemble the screw Assemble the screws(qty=6) to the corresponding position by screwdriver carefully. carefully. Doro L10 Disassembly&Assembly procedure 15/16... -
Page 16: Assemble The Battery And The Battery Cover
4.10 Assemble the Battery and the Battery cover Assemble the Battery and battery cover to the corresponding position. Doro L10 Disassembly&Assembly procedure 16/16...
Need help?
Do you have a question about the L10 and is the answer not in the manual?
Questions and answers