Channel Set Up - Magnavox CMWC20T6 Owner's Manual

B
MPAA RATING SET UP
4
Use [ K K / L L ] to point to your
desired item, then press
[ENTER] to select "BLOCK"
or "VIEW".
Selection Rating Category Explanations
G General Audience
PG Parental Guidance suggested.
PG-13 Unsuitable for children under 13
R Restricted; under 17 requires acco-
mpanying parent or adult guardian
NC-17 No one under 17 admitted
X Mature audience only
5
Press [SET-UP] to exit the menu.

CHANNEL SET UP

Channel presetting is necessary at the start or in case you moved the TV to a different area.
AUTO CHANNEL PROGRAMMING
1
Press [SET-UP].
Use [K K / L L ] to point to
"CHANNEL SET UP", then
press [ENTER].
2
Use [K K / L L ] to point to "AUTO
CH PROGRAMMING", then
press [ENTER].
The tuner scans and memorizes all the active
channels in your area.
3
When the scanning is comple-
ted, the lowest memorized
channel is displayed.
If "NO TV SIGNALS" appears
on the TV screen, check the
antenna connection and try
again.
NOTES:
• The unit may recognize CATV channels to be TV
channels if reception condition is poor. In this case,
check the antenna connection and try "AUTO CH
PROGRAMMING" again.
• Auto channel programming is NOT necessary
when connected to a cable box or satellite box.
Just select the channel for cable box or satellite
input (ex. CH3 or CH4) on the unit, then select
your desired channel on the cable box or satellite
box.
C
4
G [VIEW]
PG [VIEW]
PG–13 [VIEW]
B R [BLOCK]
NC–17 [BLOCK]
X [BLOCK]
5
ADDING/DELETING CHANNELS
You can add channels that was not memorized due
- TV/VCR SETUP -
to the bad reception status and also delete chan-
TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
nels you no longer receive or seldom watch.
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
1
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
ADD / DELETE CH (CATV)
B AUTO CH PROGRAMMING
2
CH 15
3
<EXAMPLE>
NO TV SIGNALS
• Refer to page 9 on how to use
the Number buttons.
4
• To delete another channel, repeat steps 3 to 4.
5
NOTE:
CHANGE ACCESS CODE
Use the Number buttons to
enter your desired access
code in the "NEW CODE",
then enter the same code in
the "CONFIRM CODE". When
completed, the menu will
return to "V-CHIP SET UP".
Press [SET-UP] to exit the menu.
NOTE:
• Your personal access code will be erased and will
return to the default (0000) when a power failure
occurs or when you turn off the power using a wall
switch. If you forget the code, unplug the power cord
for 10 seconds to restore the access code to 0000.
Press [SET-UP].
Use [K K / L L ] to point to
"CHANNEL SET UP", then
press [ENTER].
Use [K K / L L ] to point to
"ADD/DELETE CH", then
press [ENTER].
Use the Number buttons or
[CH. K K / L L ] to select your
desired channel number.
(You can also use [K K / L L ] to
enter it.)
Press [ENTER] repeatedly. The channel number
changes to red (deleted) or blue (added) every
time you press the button.
Press [SET-UP] to exit the menu.
• To confirm that channel(s) has(have) been deleted
or added, select it (them) using [CH. K K / L L ].
NEW CODE
X X X X
CONFIRM CODE
_ _ _ _
TV/VCR TV/VCR
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
ADD / DELETE
(Example: CH8)
13
EN