Page 1
Technical Support and E-Warranty Certificate www.vevor.com/support DOG GROOMING TUB MODEL: K1E01017/K1E01018 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
Page 3
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
IMPORTANT SAFEGUARDS WARNING: Read and understand this entire manual before operating or servicing this product. Failure to follow these warnings and instructions can cause personal injury or damage to valuable property. Avoid children using grooming tub. And this product is not a toy. Do not allow children to play.
Page 5
Gloves,goggles Caution:Before installing the product, wear gloves and goggles to avoid possible physical damage during installation. INSTRUCTIONS Thank you very much for choosing this pet bathtub. Please read all the instructions before using it. The information will help you achieve the best possible results.
Page 7
AM*1 AN*2 Water filter Handle plate Installation steps ① Install the adjustable feet(U) to the H rack(A), and fix the tube(F) to the H rack(A) orizontal Caution:Ensure that the depth of adjustable feet is not less than 12mm, and try to make the four adjustable feet screw in the same depth.
Page 8
Left Door Right Door ③ Adjust the height of the feet to make sure the height of water outlet side is 1-2 degrees lower than the other side (use a spirit level to show). ④ Install the strainer(N),Ensure that the sealing ring is free of dislocation and wrinkles.
Page 9
⑥ Install the handle(AN) to the water filter plate(AM) ⑦ Install door(E) and put the water filter plate to the tub(B) Use screw(Z) to fix the stair ⑧ board(AH) and ladder rod(AJ), then install the adjustable feet(U) on the bottom of the ladder rod(AH). Caution:Ensure that the depth of adjustable feet is not less than 12mm, and try to make the two...
Page 10
⑨ Install the stairs into the chassis rails ⑩ Use screw(P) and hex flange (Q) to install the storage basket(J) to the b ack panel ⑪ Use screw(P) and hex flange (Q) to install the s hower bracket to the right side panel(C) - 8 -...
Page 11
⑪ Install hot and cold shower switch and water inlet. Caution:Before you do this, make sure that your water source is on the left or right side of the bathtub, and select the direction of installation of the tap switch. Step1:Pass straight all-copper connector(AD) through side panel (1/2“...
Model# L(mm) H(mm) H1(mm) H2(mm) W(mm) N.W. (kg) K1E01017 1220 29.7 K1E01018 1220 29.7 Volume Loading Capacity Recommended pet Model# (CBM) (lbs) (in) K1E01017 0.35 L×W×H:33×16×18 K1E01018 0.35 L×W×H:33×16×18 OPERATION 1. Make sure the water pipe connection is complete and the water is flowing normally.
the drain to avoid clogging. 3.Please clean the transparent cover of the drain regularly,After disassembly like a nut, it can be easily cleaned, and be careful not to leave the seal ring when installing it back. CARE INSTRUCTIONS Don't put the bathtub on an uneven surface. Don’t drop or mistreat the bathtub.
Page 16
Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the K1E01017 and is the answer not in the manual?
Questions and answers