Page 1
Technical Support and E-Warranty Certificate www.vevor.com/support DOG GROOMING TUB MODEL: K1E01021/K1E01022 We continue to be committed to provide you tools with competitive price. "Save Half", "Half Price" or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us.
Page 3
This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
IMPORTANT SAFEGUARDS WARNING: Read and understand this entire manual before operating or servicing this product. Failure to follow these warnings and instructions can cause personal injury or damage to valuable property. Avoid children using grooming tub. And this product is not a toy. Do not allow children to play.
Page 5
Caution:Before installing the product, wear gloves and goggles to avoid possible physical damage during installation. INSTRUCTIONS Thank you very much for choosing this pet bathtub. Please read all the instructions before using it. The information will help you achieve the best possible results.
Page 7
Installation steps ① Install the adjustable feet(U) to the H rack(A). Caution:Ensure that the depth of adjustable feet is not less than 12mm, and try to make the four adjustable feet screw in the same depth. Please tighten the spare nut during the installation, and adjust it later.
Page 8
④ Install the strainer(N),Ensure that the sealing ring is free of dislocation and wrinkles. Caution:When installing, please pay attention to whether the sealing ring is placed correctly,avoid water leakage due to incorrect seal installation. ⑤ Use screw(Y) to fix the left and right side board(D&C), then use screw(Y) to fix the back panel(G), last to use screw(Y) to fix side...
Page 9
⑦ Install door(E) and put the water filter plate to the tub(B) ⑧ Use screw(Z) to fix the stair board(AH) and ladder rod(AJ), then install the adjustable feet(U) on the bottom of the ladder rod(AH). Caution:Ensure that the depth of adjustable feet is not less than 12mm, and try to make the two adjustable feet screw in the same...
Page 10
⑩ Use screw(P) and hex flange nut (Q) to install the storage basket(J) and shower bracket(S) to the right side panel(C) ⑪ Install hot and cold shower switch and water inlet. Caution:Before you do this, make sure that your water source is on the left or right side of the bathtub, and select the direction of installation of the tap switch.
can make the installation more sealed and help prevent water leakage at the joint. ⑬ Use screw(Y) to fix the crossbar (AB) to the left and right-side panel, then install the sling(V) DIMENSIONS AND PARAMETERS Left Door - 9 -...
OPERATION 1. Make sure the water pipe connection is complete and the water is flowing normally. (Connect the hot and cold water pipes according to the hot and cold water signs of the faucet switch). ”C”: Cold water; “H”: Hot water 2.
CARE INSTRUCTIONS Don't put the bathtub on an uneven surface. Don’t drop or mistreat the bathtub. Don’t overload the scale. This will permanently damage it! COMMON MALFUNCTIONS If the faucet leaks, please check whether the waterproof rubber plug is installed. If it is damaged, it needs to be replaced in time. Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.
Page 16
Technical Support and E-Warranty Certificate www.vevor.com/support...
Need help?
Do you have a question about the K1E01021 and is the answer not in the manual?
Questions and answers