LG MULTI V S ARUN060GSS4 Installation Manual page 28

28
Setting the function
Select the mode/function/option/value using '▶', '◀' Button and con-
firm that using the '●' button after DIP switch No.5 is turned on.
5, 6, 8 Ton
7-Segment
SW01C
SW01D
( :confirm)
(reset)
SW02C
SW04C
( :backward)
(x:cancel)
SW03C
DIP-SWITCH
( :forward)
Mode Function
Content Display1 Content Display2 Content
áâ
Cool & Heat Selector oFF
High Static Pressure
áã
oFF
Compensation mode
Night Low Noise
áä
oFF
mode
áæ
ODU address setting -
Snow removal &
áç
oFF
rapid defrost
Airflow Adjusting for
áè
IDU (Heating capacity oFF
à
up)
Target Pressure Ad-
áé
oFF
justing
High Efficiency Mode
áê
oFF
(Cooling Operation)
Compressor Max.
áâã
0
Frequency Limit
ODU Fan Max. RPM
áâä
0
Limit mode
Smart Load Control
áâå
oFF
Mode setting
Priority Heating Oper-
áãæ
oFF on/oFF
ation
* Functions save in EEPROM will be kept continuously, though the
system power was reset.
* DIP switch 3 can be OFF except when installing the only 4 series in-
door units (named ARNU***4).
2, 3, 4, 4.4 Ton
DIP-SW01 7 - Segment
SW04C
(x: cancel)
SW03C
( : forward)
SW02C
( : backward)
SW01C
( : confirm)
SW01D (reset)
Option Value Action
Display3 Content Display4 Implement Display5
oP1 Selected Change the
- - Blank
~oP2 the option set value
oP1 Selected Change the
- - Blank
~oP3 the option set value
oP1 Selected Change the
- - Blank
~oP15 the option set value
Set the Change the
- - 0~254 Blank
value set value
oP1 Selected Change the
- - Blank
~oP3 the option set value
Selected Change the
on - - Blank
the option set value
oP1 Selected Change the
- - Blank
~oP6 the option set value
Selected Change the
on - - Blank
the option set value
Selected Change the
5~180 - - Blank
the option set value
400 Selected Change the
- - Blank
~1 200 the option set value
oP1 Selected Change the
- - Blank
~oP3 the option set value
Selected Change the
- - Blank
the option set value
CAUTION
!
• To perform the otional funtion should be sure that All the IDU is off
mode, unless the function will not be performed.
Group Number setting
Group Number setting for Indoor Units
- Confirm the power of whole system(Indoor Unit, Outdoor Unit) is
OFF, otherwise turn off.
- The communication cables connected to CEN.A and CEN.B terminal
should be connected to central control of Outdoor Unit with care for
their polarity (A-A, B-B ).
- Turn the whole system on.
- Set the group and Indoor Unit number with a wired remote control.
- To control several sets of Indoor Units into a group, set the group ID
from 0 to F for this purpose.
Outdoor Units (External PCB)
SODU.B SODU.A IDU.B IDU.A
Remark
Save in
EEPROM
Save in
EEPROM
Example) Group number setting
Save in
EEPROM
1 F
Save in
Group Indoor unit
EEPROM
st
Save in
1 number indicate the group number
EEPROM
2nd number point out indoor unit number
Save in
Group recognizing the central controller
EEPROM
Save in
EEPROM
Save in
EEPROM
Save in
EEPROM
Save in
EEPROM
Save in
EEPROM
Save in
EEPROM
Cool & Heat selector (Fn 1)
Mode setting method
Master unit PCB DIP switch on : No.5
Select the mode using '▶', '◀' Button :
"Func" Push the '●' button
Select the Function using '▶', '◀' Button :
"Fn1" Push the '●' button
Select the Option using '▶', '◀' Button :
"oFF","oP1","oP2" Push the '●' button
Cool & Heat Selection mode is set
CEN.B CEN.A DRY1 DRY2 GND
B(D) A(C)
No.0 group (00~0F)
No.1 group (10~1F)
No.2 group (20~2F)
No.3 group (30~3F)
No.4 group (40~4F)
No.5 group (50~5F)
No.6 group (60~6F)
No.7 group (70~7F)
No.8 group (80~8F)
No.9 group (90~9F)
No. A group (A0~AF)
No. B group (B0~BF)
No. C group (C0~CF)
No. D group (D0~DF)
No. E group (E0~EF)
No. F group (F0~FF)
12V