Page 1
User manual / Assembly instructions TotaLuxe Veranda Type Cobh...
Page 2
TotaLuxe accepts no liability for any damage or injury resulting from a failure to carefully follow the instructions in this manual or exercise due caution during transport, assembly, use and maintenance of the veranda. As a result of our policy of continuous product improvement, certain product details may differ from what is described in this manual.
1. Introduction Before you can start enjoying your Veranda it must be assembled properly. This manual provides clear instructions for all the steps you must complete for correct assembly of your TotaLuxe Veranda. We recommend that you take the time to read the entire manual before you begin assembly.
Page 4
2. Safety precautions and warnings (continued) will Assembly Manual - Cobh Veranda Page 4...
Page 23
Cut two U-profiles to size, the length of the U-profile is determined by the number of Alumina parts that you will use. A top cover will be placed on the top of the Alumina fencing. For a standard Cobh veranda, you will need 6 Alumina parts + 1 top cover = 914mm. Assembly Manual - Cobh Veranda...
Page 24
(Make sure you place the Alumina profiles properly, otherwise the top cover will not fit). Connect the Alumina parts and the U-profiles with each other by screwing a few screws through the side wall of the U-profiles into the Alumina parts. Pre-drill first. Assembly Manual - Cobh Veranda Page 24...
Page 25
Installing the Alumina parts for the back wall Assembly Manual - Cobh Veranda Page 25...
Page 26
Connect the Alumina parts and the U-profiles with each other by screwing a few screws through the side wall of the U-profiled into the Alumina parts. Pre-drill first Repeat these steps for the other side of the back wall. Assembly Manual - Cobh Veranda Page 26...
Page 27
Alumina parts 1 by 1 in the U-profiles from above. The profiles click together with a little force. Finally, place the top cover. (Make sure you place the Alumina profiles properly, otherwise the top cover will not fit). Assembly Manual - Cobh Veranda Page 27...
Page 28
Click the Alumina parts together above the polycarbonate sheet and slide them into the U- profiles. The lower Alumina falls over the polycarbonate sheet. Assembly Manual - Cobh Veranda Page 28...
Page 29
Place the last u-profile over the top of the cut Alumina parts. Assembly Manual - Cobh Veranda Page 29...
Page 43
1. Position the rubber strip in the wall profile properly so it covers the sheets and cover strips. 2. Carefully cut the rubber strip to size at both ends. Silicon spray 3. Screw the wall profile side cover onto wall profile with two short screws. Assembly Manual - Cobh Veranda Page 43...
Page 44
5. Carefully screw the decorative profile side cover to the gutter profile and the decorative profile with the short screws in the guides provided for this purpose. 6. Apply sealant on the inside of the gutter so it is waterproof. www.deponti.com Assembly Manual – Ribolla Veranda page44 Assembly Manual - Cobh Veranda Page 44...
Page 45
7. Now attach the sheet stoppers to the cover strips of the end beams with the short screws. 8. Remove the protective film from the roofing sheets and the aluminium parts. www.deponti.com Assembly Manual – Ribolla Veranda page44 Assembly Manual - Cobh Veranda...
Page 46
10. If there is a small gap between the top of the posts and the gutter you can seal it with sealant. 11. Congratulations! The roof is now finished! www.deponti.com Assembly Manual – Ribolla Veranda page44 Assembly Manual - Cobh Veranda...
The powder coating has a 5-year warranty. Please note, the powder coating warranty of aluminium parts is two years when the product is placed in a place where it comes into contact with salty or chemical steam (such as harbours, coast and swimming pools). 10. Contact Assembly Manual - Cobh Veranda Page 47...
Need help?
Do you have a question about the TotaLuxe Cobh and is the answer not in the manual?
Questions and answers