Download Print this page

Safavieh Furniture Conall NST3103 Manual

2 drawer nightstand

Advertisement

Quick Links

NOTICE
*Please make sure that you have all part indicated and they are in good condition before you
begin assembly of this item. Refer to part list and hardware list below for guidance.
*This item should be assembled on a soft surface to prevent scratching the finish during
assembly.
*This item may require periodic tightening.
*If you are having difficulty, our friendly Customer Care team is always here to help. Please
email customersupport@safavieh.com
PREPARATION
*Before beginning assembly of product, make sure all part are present. Compare part with
part contents list and hardware contents list.
*If any part is missing or damaged, do not attempt to assemble the product.
*Estimated Assembly Time: 60 minutes.
*Tools Required for Assembly (Not included): Screwdriver
CARE AND MAINTENANCE
Always use felt pads under all articles to prevent discoloration or softening of the lacquer.
Plastic and rubber bases on items can discolor wood. Wipe up spills immediately and avoid
common hazards such as hot dishes, harsh solvents and abrasives. Cleaning should be done
with a soft lint free cotton cloth dampened with water or furniture polish. On highly used surfaces
we recommend applying a quality paste wax which should be used on a regular basis to provide
additional protection from scratches and spills. How often you apply the wax depends on how
much wear the furniture receives.
Part List
14
18
17
14
19
17
15
13
5
6
2
8
16
15
13
10
16
12
11
11
1
4
3
7
9
Model# NST3103
Product Dimensions: W 22.83" x D 15.67" x H 21.85"
WARNING :
WEIGHT CAPACITY :
Top : 26 Lbs
Drawer : 11 Lbs
Warning : Do not stand on the product.
Warning : Do not over torque bolts.

Advertisement

loading
Need help?

Need help?

Do you have a question about the Conall NST3103 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Safavieh Furniture Conall NST3103

  • Page 1 NOTICE *Please make sure that you have all part indicated and they are in good condition before you begin assembly of this item. Refer to part list and hardware list below for guidance. *This item should be assembled on a soft surface to prevent scratching the finish during assembly.
  • Page 2: Hardware List

    Hardware List Ax33 Bx33 Cx27 Ex10 Ø6x32 mm Ø8x32 mm Ø4x19 mm Ø7x32 mm Ø15x12 mm ASx2 CQx4 Sx16 AYx8 CPx1 Ø20 mm Ø5x8.5 mm 310 mm Ø4x10 mm list "H" 547 mm...
  • Page 3 Part List & HW Piece Description Carton Call Piece Description Carton Call Right Side Panel 1 of 1 1 of 1 Cambolt Left Side Panel 1 of 1 Camlock 1 of 1 Back Fixed Shelf 1 of 1 Wooden Dowel 1 of 1 Bottom Support 1 of 1...
  • Page 4 PREPARATION Before beginning assembly of product, make sure all part are present. Compare part with part contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. Estimated Assembly Time: 60 minutes. STEP1: STEP2: Insert Cambolt (A) into Upper Front Drawer (18) And Lower Front...
  • Page 5 STEP5: Combine Back Fixed Shelf (3) into Bottom support (4) STEP6: Insert Wooden Dowel (C) into front fixed shelf (5), top support (6), then tighten camlock (B) using screwdriver. right inner front cross (7) And left inside front cross (8) FRONT 1 2 3 BACK...
  • Page 6 FRONT 1 2 3 BACK 1 2 3 STEP9: Insert Cambolt (A) into left side panel (2).Insert Wooden Dowel (C) into left Side Panel (2). STEP10: Install the mini slide runner (AS) into position as shown in picture. Attach Left side panel (2) and Left inside front cross (8) Secure with screws M5x8,5mm (AY).
  • Page 7 STEP13: Insert Back panel 2x (9), And List "H" (CP) STEP14:Insert Cambolt (A) into top panel (12) STEP15: STEP16: Insert top panel (12), Secure with Camlock (B) and Attach the plastic stopper (O) to the back panel Secure tighten it using screwdriver. with screw M4x19 mm (H) and tighten it using screwdriver.
  • Page 8 STEP17: Insert the assembled drawer, Secure with Bolt M4x10 mm (CQ) and tighten it using screwdriver. STEP18: Attach cover cap sticker (S) to the panel that has lamination STEP19: Assembly is complete...

This manual is also suitable for:

Conall nst3103a