1. Manuals
  2. Brands
  3. brent Manuals
  4. Farm Equipment
  5. V1300
  6. Manual

brent V1300 Manual

Corner-auger grain cart
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Grain Handling
CORNER-AUGER GRAIN CART
MODELS V1300 / V1500
Serial Number B45580100 & Higher
Part Number 297936

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V1300 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for brent V1300

Summary of Contents for brent V1300

  • Page 1 Grain Handling CORNER-AUGER GRAIN CART MODELS V1300 / V1500 Serial Number B45580100 & Higher Part Number 297936...
  • Page 2 — Introduction Brent V1300 / V1500 Foreword This symbol identifies important safety messages. When you see it, read the message that follows and be alert to the possibility of personal injury. Remember, safety instructions stated in this manual are for your protection. Read them care- fully and follow them closely when working around or using this machine.

  • Page 3: Product Information

    — Introduction Brent V1300 / V1500 Product Information When ordering parts or when requesting further information or assistance, always give the following information: • Machine name • Model • Serial Number All products manufactured by Unverferth Mfg. Co., Inc. are warranted to be free from ma- terial and workmanship defects for one full year from time of consumer delivery.

  • Page 4: Table Of Contents

    — Introduction Brent V1300 / V1500 Table of Contents Section I Safety General Hazard Information ......................1-2 Safety Decals ..........................1-3 Following Safety Instructions ......................1-5 Before Servicing or Operating ......................1-6 During Operation ..........................1-6 Before Transporting ......................... 1-7 During Transport..........................
  • Page 5 — Introduction Brent V1300 / V1500 Table of Contents Section II Set Up Set Up Checklist ..........................2-2 Set Up............................. 2-3 SMV Emblem & SIS Decal ......................2-4 Auger Rest Retainer Removal......................2-5 Jack and Optional Hydraulic Jack ....................2-6 Jack ............................
  • Page 6 — Introduction Brent V1300 / V1500 Table of Contents Section III Operation Operating Checklist ......................... 3-2 Preparing Tractor..........................3-2 Preparing Cart..........................3-3 Hardware ..........................3-3 Pivot Pins ..........................3-3 Hitch ............................3-3 Auger ............................3-3 Auger Driveline Assembly......................3-4 Soft Start System........................3-4 Hydraulic System........................
  • Page 7 — Introduction Brent V1300 / V1500 Table of Contents Section IV Maintenance Lubrication............................4-2 Gearbox Lubrication ........................4-3 Hydraulic System ..........................4-4 Purge Hydraulic System ......................4-4 Manual Override for Optional Electric Over Hydraulic System ............4-5 Auger System..........................4-8 Lower Auger ..........................
  • Page 8 Clean Out Door Assembly......................5-7 Flow Door Seals ........................5-8 Directional Spout........................5-10 Wheel Well Cover Kit (V1300 Only) ..................5-14 Wheel Well Cover Kit (V1500 Only) ..................5-15 Rear Ladder Components ......................5-16 Rear Access Door Components ....................5-17 Sideboards..........................
  • Page 9 — Safety Brent V1300 / V1500 Section I Safety General Hazard Information ......................1-2 Safety Decals ..........................1-3 Following Safety Instructions ......................1-5 Before Servicing or Operating ......................1-6 During Operation ..........................1-6 Before Transporting ......................... 1-7 During Transport..........................1-7 Driveline Safety ..........................

  • Page 10: Safety

    — Safety Brent V1300 / V1500 General Hazard Information No accident-prevention program can be successful without the wholehearted cooperation of the person who is directly responsible for the operation of the equipment. A large number of accidents can be prevented only by the operator anticipating the result before the accident is caused and doing something about it.

  • Page 11: Safety Decals

    — Safety Brent V1300 / V1500 Safety Decals • REPLACE LOST, DAMAGED, PAINTED, OR UNREADABLE DECALS IMMEDIATELY. IF PARTS THAT HAVE DECALS ARE REPLACED, ALSO MAKE SURE TO INSTALL NEW DECALS. THESE DECALS INFORM AND REMIND THE OPERATOR WITH OPERATIONAL INFORMATION AND SAFETY MESSAGES.
  • Page 12 — Safety Brent V1300 / V1500 Safety Decals (continued) TA510514 9003475 95008 95839 9003478 9003476 PART NO. 9003125 95046 FLUORESCENT STRIP 9008714 9008720 PART NO. 9003126 REFLECTOR RED PART NO. 9003127 REFLECTOR AMBER...

  • Page 13: Following Safety Instructions

    — Safety Brent V1300 / V1500 Following Safety Instructions • Read and understand this operator’s manual before operating. • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts approved by the manufacturer.

  • Page 14: Before Servicing Or Operating

    — Safety Brent V1300 / V1500 Before Servicing or Operating • Avoid working under an implement; however, if it becomes absolutely unavoid- able, make sure the implement is safely blocked. • Ensure that all applicable safety decals are installed and legible.

  • Page 15: Before Transporting

    — Safety Brent V1300 / V1500 Before Transporting • Verify transport chain capacity meets or exceeds weight capacity of all towed implements. Secure transport chains to towing vehicle before transporting. DO NOT transport without chains. • Check for proper function of all available transport lights. Make sure that all reflectors are clean and in place on machine.

  • Page 16: Driveline Safety

    — Safety Brent V1300 / V1500 Driveline Safety • Do not allow children near equipment that is running or engaged. • Do not exceed 1000 rpm PTO speed. • Disengage the PTO, stop the tractor engine, and remove key from ignition before making inspections, or performing maintenance and repairs.

  • Page 17: Pressurized Oil

    — Safety Brent V1300 / V1500 Pressurized Oil • Relieve the hydraulic system of all pressure before adjusting or servicing. See hydraulic power unit manual for procedure to relieve pressure. • High-pressure fluids can penetrate the skin and cause serious injury or death.

  • Page 18: Preparing For Emergencies

    — Safety Brent V1300 / V1500 Preparing for Emergencies • Keep a first aid kit and properly rated fire extinguisher nearby. • Keep emergency numbers for fire, rescue, and poison control personnel near the phone. Wearing Protective Equipment • Wear clothing and personal protective equipment appropriate for the job.

  • Page 19: Set Up

    — Set Up Brent V1300 / V1500 Section II Set Up Set Up Checklist ..........................2-2 Set Up............................. 2-3 SMV Emblem & SIS Decal ......................2-4 Auger Rest Retainer Removal......................2-5 Jack and Optional Hydraulic Jack ....................2-6 Jack ............................2-6 Install Hydraulic Jack (Optional)....................

  • Page 20: Set Up Checklist

    — Set Up Brent V1300 / V1500 Set Up Checklist After the cart has been completely assembled, use the following checklist and inspect the cart. Check off each item as it is found satisfactory or after proper adjustment is made.

  • Page 21: Set Up

    — Set Up Brent V1300 / V1500 Set Up Sideboards FIG. 2-1 Wheels/Tires & Wheel Nuts Due to shipping requirements and various dealer-installed options, some initial cart set up will be required after it arrives from the factory. Use the following procedures as needed for initial cart set up.

  • Page 22: Smv Emblem & Sis Decal

    — Set Up Brent V1300 / V1500 SMV Emblem & SIS Decals Before the cart is used, the reflective surface FIG. 2-2 of the SMV must face rearward. This may re- quire removal of film protecting the reflective surface or removing and reinstallation of the SMV.

  • Page 23: Auger Rest Retainer Removal

    — Set Up Brent V1300 / V1500 Auger Rest Retainer Removal Remove and discard the retainer located on FIG. 2-6 the upper auger rest at the back of the cart, before folding out the upper auger tube, (Fig. 2-6 and 2-7) •...

  • Page 24: Jack

    — Set Up Brent V1300 / V1500 Jack & Optional Hydraulic Jack Set Up Jack • UNHITCHING A LOADED CART CAN CAUSE SERIOUS INJURY OR DEATH DUE TO THE TONGUE RISING OR FALLING. ALWAYS HAVE A LOADED CART ATTACHED TO A TRACTOR.
  • Page 25 — Set Up Brent V1300 / V1500 Jack & Optional Hydraulic Jack Set Up (continued) Install Hydraulic Jack (Optional) (continued) 9009047 FIG. 2-11 • KEEP HANDS CLEAR OF PINCH POINT AREAS. 3. Assemble the cylinder (9009047) and 9390-197 jack foot (271723B) to the jack weldment (271712B) as shown in figure 2-11 using 1”-8UNC x 7”...

  • Page 26: Lamp Set Up

    — Set Up Brent V1300 / V1500 Lamp Set Up Pivot lamp extension arms into position at sides of cart. The lamp bracket width is adjustable. Adjust lamp mount position to ensure that the reflectors are no more than 16” from the wid- est part of the tires, tracks, or grain cart body.

  • Page 27: Wheel & Tire Set Up

    — Set Up Brent V1300 / V1500 Wheel & Tire Set Up Tire Pressure Tire pressure must be verified before first use and adjusted as necessary. Refer to MAINTENANCE section of this manual for information on tire pressure. Wheel Nuts •...

  • Page 28: Spindle Positioning

    — Set Up Brent V1300 / V1500 Spindle Positioning • Single tire hubs and spindles are slid in for shipping and need to be slid out before attaching wheels/tires to provide adequate clearance between tires and wheel wells. Spindles on carts with single wheels are moved inward for transportation.
  • Page 29 — Set Up Brent V1300 / V1500 Sideboards and End Caps Installation 1. Park the empty grain cart on a firm, level surface. Block the machine to keep it from moving. Set the tractor’s parking brake, shut-off the engine, remove the ignition key and disconnect the PTO shaft.

  • Page 30: Sideboards And End Caps

    — Set Up Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 6. Remove and discard shipping bracket for FIG. 2-21 left-hand sideboard. (Fig. 2-21) 7. Lift the left-hand sideboards into position. NOTE: Hinge brackets WILL support the side- board and tarp.
  • Page 31 (Fig. 2-24) 10. ONE PIECE BRACE TUBE: FIG. 2-25 Install two sideboard brace tubes (287692B Install The - V1300; 288653B - V1500) to the left- Sideboard hand sideboards and center cross tube Brace Tube weldments, and two sideboard brace tubes (220032B) to right-hand sideboards and center cross tube weldments.
  • Page 32 — Set Up Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 12. Remove and discard the shocks and associ- FIG. 2-27 ated brackets from the left-hand sideboard. 13. Remove and discard the shipping brackets from the rear and front sideboards. Front sideboard shown in figure 2-27.
  • Page 33 (95585) and flange nuts (91263) along the bottom. (Fig. 2-30) 18. Loosely attach small rear sideboard to the left-hand sideboard using the left-hand rear sideboard corner bolt plate (295678B - V1300; 296381B - V1500) on the outside of the sideboards with (9388-051) and (91263) hardware. (Fig. 2-30)
  • Page 34 Sideboards and End Caps Installation (continued) 21. Attach small rear end cap (288343B - Small End FIG. 2-32 V1300; 288647B - V1500) on top of rear Cap Tab sideboard. Loosely secure using flange screws (95585) and flange nuts (91263) Left-Hand hardware along the bottom.
  • Page 35 Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 23. Attach large rear end cap (296131B - V1300; 296143B - V1500) on top of rear sideboard using flange screws (95585) and flange nuts (91263) along the bottom. (Fig. 2-34) NOTE: Tabs on smaller end cap go UNDER the larger end cap.
  • Page 36 — Set Up Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 25. Positon right-hand end cap plate (283431B) FIG. 2-35 Right-Hand between the end cap and right-hand side- End Cap Plate board. (Fig. 2-35 through 2-37) (283431B) 26. Loosely retain by using two truss head...
  • Page 37 — Set Up Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 27. Lift large front sideboard (297652B - V1300; 297653B - V1500) into position. (Fig. 2-38) Small End Cap Large End Cap Left-Hand Front Corner Sideboard Bolt Plate...
  • Page 38 — Set Up Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 33. Attach small front end cap (288341B - FIG. 2-40 V1300; 288646B - V1500) on top of front Left-Hand End Cap Plate sideboards. Loosely secure using flange (295668B) screws (95585) and flange nuts (91263) hardware along the bottom.
  • Page 39 Brent V1300 / V1500 Sideboards and End Caps Installation (continued) 35. Attach large front end cap (296129B - V1300; 296142B - V1500) on top of front side- boards using flange screws (95585) and flange nuts (91263) hardware along the bottom.

  • Page 40: Tarp Installation

    — Set Up Brent V1300 / V1500 Tarp Installation NOTE: Ensure RH and LH doublers are inside the sideboard lip. (Fig. 2-44) NOTE: For each of the eight tarp bows, complete the following steps: 1. Attach a doubler (right-hand 289986B, left-hand (281936B) under the sideboard lip and secure with truss screws ( and flange nuts (91263).
  • Page 41 Brent V1300 / V1500 Tarp Installation (continued) 3. Install eight long tarp bows (288339B for V1300; 288640B for V1500) across the top of the cart using 3/8”-16UNC x 3” flat hex capscrew (902703-046), 3/8”-16UNC (91263) flange nut, 5/16”-18UNC x 3/4” flange screw (91256) and 5/16”-18UNC flange nut (91257). (Fig.
  • Page 42 — Set Up Brent V1300 / V1500 Tarp Installation (continued) 7. Install four bracket & U-nut assemblies FIG. 2-48 Attach Tarp Cables (281712B) using 3/8”-16UNC x 4 1/2” Capscrew capscrews (TA0-907131-0), 3/8” lock (TA0-907131-0) washers (9005688), and 3/8” fender washers (9005696). (Fig. 2-48)
  • Page 43 — Set Up Brent V1300 / V1500 Tarp Installation (continued) 10. Attach the crank handle (287944) to the FIG. 2-52 tarp roll tube (288360) and secure with roll pin (9092-180). Roll tarp across the cart to the closed position. (Fig. 2-52) Attach to Roll Tube NOTE: Remove zip ties holding tarp roll.
  • Page 44 — Set Up Brent V1300 / V1500 Tarp Installation (continued) 13. Begining at the front of the cart, use #10-16 FIG. 2-54 x 3/4” self-drilling screws (9005197) and U- clamps (9004949) to secure tarp in place on the roll tube. Check that clips are located on the straps with an even height across.

  • Page 45: Operational Check

    — Set Up Brent V1300 / V1500 Operational Check • MOVING OR ROTATING COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH. EN- SURE SERVICE COVERS, CHAIN/BELT COVERS AND CLEAN-OUT DOOR ARE IN PLACE AND SECURELY FASTENED BEFORE OPERATING UNIT. • Before running the auger, inspect and verify all grain dust and filings are removed from inside the lower auger to prevent machine damage and the cleanout door is completely closed.
  • Page 46 — Set Up Brent V1300 / V1500 Notes 2-28...
  • Page 47 — Operation Brent V1300 / V1500 Section III Operation Operating Checklist ......................... 3-2 Preparing Tractor..........................3-2 Preparing Cart..........................3-3 Hardware ..........................3-3 Pivot Pins ..........................3-3 Hitch ............................3-3 Auger ............................3-3 Auger Driveline Assembly......................3-4 Soft Start System........................3-4 Hydraulic System........................

  • Page 48: Operating Checklist

    — Operation Brent V1300 / V1500 Operating Checklist  Read and understand all safety precautions before operating cart.  R.V. antifreeze needs to be completely flushed from the Water Delivery System and disposed of properly. Make certain the Water Delivery System only contains water before placing the Water Delivery System in service.

  • Page 49: Preparing Cart

    — Operation Brent V1300 / V1500 Preparing Tractor (continued) Verify that the tractor is adequately ballasted for drawbar operation at the anticipated draft load. See tractor manual for ballasting instructions. If possible, adjust the tractor drawbar vertically so the topside of the drawbar is approximately 17-22 inches from the ground.

  • Page 50: Auger Driveline Assembly

    — Operation Brent V1300 / V1500 Preparing Cart (continued) Auger Driveline Assembly Check all bearings, bearing mounts, lock collars, universal joint, front and rear driveshafts for wear or damage. Repair or replace all bearings, bearing mounts, lock collars, universal joint, front and rear driveshafts as necessary.

  • Page 51: Hitching To Tractor

    — Operation Brent V1300 / V1500 Hitching to Tractor Drawbar Connection This cart is intended to be hitched to a tractor drawbar. Do not attempt to hitch to FIG. 3-1 any other location on the tractor other than the drawbar.

  • Page 52: Jack Usage

    — Operation Brent V1300 / V1500 Hitching to Tractor (continued) Jack Usage • UNHITCHING A LOADED CART CAN CAUSE SERIOUS INJURY OR DEATH DUE TO THE TONGUE RISING OR FALLING. ALWAYS HAVE A LOADED CART ATTACHED TO A TRACTOR. THE JACK IS INTENDED TO SUPPORT AN EMPTY CART ONLY.

  • Page 53: Optional Hydraulic Jack Usage

    — Operation Brent V1300 / V1500 Hitching to Tractor (continued) Optional Hydraulic Jack Usage • UNHITCHING A LOADED CART CAN CAUSE SERIOUS INJURY OR DEATH DUE TO THE TONGUE RISING OR FALLING. ALWAYS HAVE A LOADED CART ATTACHED TO A TRACTOR.

  • Page 54: Transport Chain Connection

    — Operation Brent V1300 / V1500 Hitching to Tractor (continued) Transport Chain Connection • ALWAYS USE TRANSPORT CHAIN WHEN TRANSPORTING IMPLEMENTS. FAILURE TO USE A TRANSPORT CHAIN COULD CAUSE PERSONAL INJURY IF CART BECOMES DISENGAGED. • REPLACE TRANSPORT CHAIN IF ANY LINK OR END FITTING IS BROKEN, STRETCHED, DAMAGED OR NOT FUNCTIONING.

  • Page 55: Hydraulic Connections For Hydraulic Drive

    — Operation Brent V1300 / V1500 Hitching to Tractor (continued) Clean hydraulic hose couplers before connecting to the tractor. For convenience, it is recom- mended to connect the flow door circuit hoses to tractor implement coupler #1, auger spout circuit hoses to couplers #2 and #3, and attach auger fold circuit to coupler #4.

  • Page 56: Hydraulic Connections For Optional Water Delivery System

    — Operation Brent V1300 / V1500 Hitching to Tractor (continued) Hydraulic Connections For Optional Water Delivery System Pump (TA825350) FIG. 3-9 Flow Limiter/Velocity Fuse (TA827039) Closed Center System ONLY Hydraulic Hoses (See Parts Section For Sizes) Hose Grip (Blue) (+) (9009749) Pump Hydraulic Pressure &...

  • Page 57: Electrical Connections

    — Operation Brent V1300 / V1500 Hitching to Tractor (continued) Electrical Connections This cart is equipped with a seven-pin SAE con- nector plug that will connect with the receptacle found on most newer tractors. If your tractor does not have this type of receptacle, an SAE J-560 seven-point socket can be purchased from your Unverferth dealer (Part number 92824).
  • Page 58 — Operation Brent V1300 / V1500 Optional Electric Over Hydraulic Operation Optional - 4 Function Before operating cart, familarize yourself with the functions associated with the joystick con- troller by operating with an empty cart. The joystick comes with a mounting pin allowing storage inside the tractor cab when not in use.

  • Page 59: Electric Over Hydraulic Operation - 4 Function (Optional)

    — Operation Brent V1300 / V1500 Electric Over Hydraulic Operation (Optional) (continued) 5. To fold auger out from transport to operating position, depress the auger unfold button on joystick face until the upper and lower auger are engaged. See FIG. 3-12.

  • Page 60: Electric Over Hydraulic Operation - 4 Function (Optional)

    (SEE NOTE FOR SOFTWARE LOGIC) — Operation Brent V1300 / V1500 Electric Over Hydraulic Operation (Optional) (continued) 11. To open flow door, rotate the switch up- FIG. 3-13 wards. Observe flow door indicator to de- termine when to release trigger and stop FLOW DOOR OPEN flow door movement.

  • Page 61: Cart Loading Sequence

    — Operation Brent V1300 / V1500 Cart Loading Sequence • NEVER LOAD THE REAR OF A GRAIN CART FIRST. LOAD THE CART EVENLY TO MAINTAIN WEIGHT ON THE TRACTOR DRAWBAR. LOADING ONLY THE FRONT, OR ONLY THE REAR, CAN CAUSE A LOSS OF CONTROL.

  • Page 62: Towing

    — Operation Brent V1300 / V1500 Towing Ensure that the towing vehicle has adequate weight and braking capacity to tow this implement and all attachments. See your Unverferth dealer for more information. See towing vehicle’s operators manual for towing capacity. Never tow a loaded grain cart over public roads.

  • Page 63: Auger Operation

    — Operation Brent V1300 / V1500 Auger Operation • ELECTROCUTION WILL CAUSE SERIOUS INJURY OR DEATH. ELEC- TROCUTION CAN OCCUR WITHOUT DIRECT CONTACT. KEEP AWAY FROM ALL ELECTRICAL LINES AND DEVICES. • ENTANGLEMENT WITH THE DRIVELINE WILL CAUSE SERIOUS INJURY OR DEATH.
  • Page 64 — Operation Brent V1300 / V1500 Auger Operation (continued) 5. To slow or stop grain flow, close flow FIG. 3-16 door, DO NOT reduce tractor/PTO RPM as a means to control grain flow. Close flow door fully when unloading is complete. (FIG.

  • Page 65: Rear Ladder Operation

    — Operation Brent V1300 / V1500 Rear Ladder Operation • FALLING OR LOWERING EQUIPMENT CAN CAUSE SERIOUS INJURY OR DEATH. KEEP EVERYONE AWAY FROM EQUIPMENT WHEN SUSPENDED, RAISING, OR LOWERING. • DO NOT ALLOW ANYONE TO RIDE ON THE LADDER. MAKE SURE EVERYONE IS CLEAR BEFORE OPERATING MACHINE OR TOWING VEHICLE.
  • Page 66 — Operation Brent V1300 / V1500 Rear Ladder Operation (continued) 3. While holding ladder handle, slowly swing the lower ladder section completely down to working position (FIG. 3-19) Working Position Lower Ladder Fig. 3-19 Fig. 3-20 Folding Ladder 1. Slowly lift and swing the lower ladder section up to storage position.

  • Page 67: Rear Access Door Operation

    — Operation Brent V1300 / V1500 Rear Access Door Operation • ENSURE SCREENS OVER HORIZONTAL AUGERS ARE IN PLACE AND PROPERLY SECURED. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH.

  • Page 68: Weather Guard Tarp

    — Operation Brent V1300 / V1500 Weather Guard Tarp • TO PREVENT PERSONAL INJURY OR DEATH, DO NOT ALLOW ANYONE ON A CLOSED TARP. TARP SYSTEM IS NOT DESIGNED TO SUPPORT A PERSON. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. REMOVE ACCUMULATED WATER/SNOW/ICE OR ANY OTHER OBJECTS FROM TARP BEFORE OPENING TARP.
  • Page 69 — Operation Brent V1300 / V1500 Weather Guard Tarp (continued) NOTE: If equipped with wireless electric roll tarp, skip to next page. For weather guard tarp, continue to step 1. 1. Using both hands, carefully remove tarp handle weldment from tube holder. (FIG. 3-26) 2.

  • Page 70: Electric Tarp Wireless Receiver And Control Box Location

    — Operation Brent V1300 / V1500 Weather Guard Tarp (continued) Electric Tarp Wireless Receiver and Control Box Location NOTE: Refer to electric roll tarp manual (291206) FIG. 3-27 for wireless operation details. 1. Position the control box on the cart to front, left-hand side support as shown in figure 3-27.
  • Page 71 — Maintenance Brent V1300 / V1500 Section IV Maintenance Lubrication............................4-2 Gearbox Lubrication ........................4-3 Hydraulic System ..........................4-4 Purge Hydraulic System ......................4-4 Manual Override for Optional Electric Over Hydraulic System ............4-5 Auger System..........................4-8 Lower Auger ..........................4-8 Lower Auger Removal......................

  • Page 72: Lubrication

    — Maintenance Brent V1300 / V1500 Lubrication To keep your grain cart in top operating condition and to assure its proper performance and reliability for a long period of time, periodic inspection and lubrication is a must. Make sure to use NLGI-2 high quality EP grease.

  • Page 73: Gearbox Lubrication

    — Maintenance Brent V1300 / V1500 Lubrication (continued) Lubricate with quality grease before starting work and every 8 operating hours. Clean and grease PTO drive shaft before each prolonged period of non-use. Molded nipples on the shield near each shield bearing are intended as grease fittings and should be lubricated every 8 hours of operation! Check and grease the guard tubes in winter to prevent freezing.

  • Page 74: Hydraulic System

    — Maintenance Brent V1300 / V1500 Hydraulic System Refer to parts section for hydraulic component detail listing. When properly assembled and maintained, the hydraulic system of the grain cart requires little maintenance. Replacing Hoses/Fittings/Cylinders: 1. Use replacement hoses, fittings, and cylinders from your Unverferth Manufacturing dealer which are rated for 3000 psi.

  • Page 75: Manual Override For Optional Electric Over Hydraulic System

    — Maintenance Brent V1300 / V1500 Manual Override for Optional Electric Over Hydraulic System • MOVING OR ROTATING AUGER COMPONENTS CAN CAUSE SERIOUS INJURY OR MA- CHINE DAMAGE. BEFORE OPERATING MANUAL OVERRIDE(S), ENSURE EVERYONE IS AWAY FROM THE SPOUT AND THAT THE SPOUT WILL NOT CONTACT ANY OTHER PARTS OF THE GRAIN CART.
  • Page 76 — Maintenance Brent V1300 / V1500 Manual Override for Optional Electric Over Hydraulic System (continued) NOTE: Only one cartridge valve (9008416) may be in the top or bottom detent position at Cartridge Valve (9008416) a time to function properly. All other valves Top Detent must be in the middle detent postion.

  • Page 77: Auger System

    — Maintenance Brent V1300 / V1500 Auger System • TO PREVENT PERSONAL INJURY OR DEATH, ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE CART TO ASSIST THE PERSON WORKING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.

  • Page 78: Lower Auger

    — Maintenance Brent V1300 / V1500 Auger System (continued) Lower Auger 1. Hitch cart to tractor. Fully open auger flow door. Fold auger to transport position. Park the empty grain cart on a firm, level surface. Set the tractor’s parking brake, shut-off the engine and remove the ignition key.

  • Page 79: Lower Auger Assembly

    — Maintenance Brent V1300 / V1500 Auger System (continued) Lower Auger Assembly 4. The replacement auger flighting is factory balanced. Remove entire auger from shipping crate and secure from rolling. The lower auger assembly is pictured in figure 4-6 for reference.

  • Page 80: Hanger Bearing Centering

    — Maintenance Brent V1300 / V1500 Auger System (continued) Hanger Bearing Centering 8. Once the lower auger is inserted into the FIG. 4-9 auger tube, center the lower auger in the tube and support with two 5/8” thick bars/ wedges near the auger hinge plate. (Fig.

  • Page 81: U-Joint Spline Gap

    — Maintenance Brent V1300 / V1500 Auger System (continued) 10. Loosely secure the hanger bearing using one 3” x 3 9/16” left-hand shim (288679B), one 3” x 3 9/16” right-hand shim (288679B), three 5/8”-11UNC x 2” capscrews (9390-124), three 5/8” flat washers (9405-098), and three 5/8”-11UNC lock nuts (9003398). (Fig. 4-11) 5/8"...

  • Page 82: Upper Auger

    — Maintenance Brent V1300 / V1500 Auger System (continued) Upper Auger 1. Hitch cart to tractor, then fold upper auger to the transport position. Park the empty grain cart on a firm, level surface. Set the tractor’s parking brake, shut-off the engine and remove the ignition key.

  • Page 83: Soft Start Replacement

    — Maintenance Brent V1300 / V1500 Auger System (continued) Soft Start Replacement 3. Use a safe lifting device rated at a minimum of 2,000 lbs. to support the upper auger, remove auger flighting from tube. 4. Remove the 5/8”-11UNC x 9” capscrew (9390-442), 5/8”-11UNC lock nut (9801), soft start assembly, spacer bushing (405402), thrust washer (9004878), and bushing (9004877).
  • Page 84 — Maintenance Brent V1300 / V1500 Auger System (continued) Soft Start Replacement (continued) 7. Insert the 5/8”-11UNC x 9” capscrew (9390-442) through auger center-tube and soft start. Place spacer bushing (405402) over threads and retain with locknut (9801). (Fig. 4-16) NOTE: Verify that the spacer bushing is on the locknut side of the auger center tube.

  • Page 85: Upper Auger Height

    — Maintenance Brent V1300 / V1500 Auger System (continued) Upper Auger Height 9. Set upper auger in-set of 4”. With the up- per auger in the folded/transport, ensure ” the face of the soft start bushing that sits on the top of the drive dog should be 4”...

  • Page 86: Upper Auger Bearing Gap

    — Maintenance Brent V1300 / V1500 Auger System (continued) Upper Auger Bearing Gap 11. Engage PTO and test run augers to ensure FIG. 4-20 drive dogs are engaged. Stop PTO, shut off tractor and remove key. 12. Verify the upper auger bearing height by inspecting the upper auger bearing in op- 1/16”...

  • Page 87: Auger Flow Door Cylinder Replacement

    — Maintenance Brent V1300 / V1500 Auger System (continued) Auger Flow Door Cylinder Replacement • TO PREVENT PERSONAL INJURY OR DEATH, ALWAYS ENSURE THAT THERE ARE PEOPLE WHO REMAIN OUTSIDE THE CART TO ASSIST THE PERSON WORKING INSIDE, AND THAT ALL SAFE WORKPLACE PRACTICES ARE FOLLOWED. THERE IS RESTRICTED MOBILITY AND LIMITED EXIT PATHS WHEN WORKING INSIDE THE IMPLEMENT.
  • Page 88 — Maintenance Brent V1300 / V1500 Auger System (continued) Auger Flow Door Cylinder Replacement (continued) 2. On the inside of the cart, open the screen FIG. 4-23 service access panel. (Fig. 4-23) Screen Service Access Panel 3. Remove the cotter pins from the lower cylinder pin then remove the pin.
  • Page 89 — Maintenance Brent V1300 / V1500 Auger System (continued) Auger Flow Door Cylinder Replacement (continued) 6. Label the hydraulic hoses to indicate upper and lower. Disconnect them from FIG. 4-25 the cylinder, along with the lower hydraulic Remove Lower fitting. (Fig. 4-25) Hose &...

  • Page 90: Auger Floor Door Cylinder Stop

    — Maintenance Brent V1300 / V1500 Auger System (continued) Auger Floor Door Cylinder Stop • ELECTROCUTION WILL CAUSE SERIOUS INJURY OR DEATH. ELEC- TROCUTION CAN OCCUR WITHOUT DIRECT CONTACT. KEEP AWAY FROM ALL ELECTRICAL LINES AND DEVICES. • ENTANGLEMENT WITH THE DRIVELINE WILL CAUSE SERIOUS INJURY OR DEATH.

  • Page 91: Auger Driveline

    — Maintenance Brent V1300 / V1500 Auger Driveline • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING IMPLEMENT. • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED.
  • Page 92 — Maintenance Brent V1300 / V1500 Auger Driveline Disassembly 1. Park the empty unit on a firm, level surface. Block the machine to keep it from moving. Set the tractor parking brake, shut off the engine, and remove the ignition key from the tractor before disconnecting driveline FIG.
  • Page 93 — Maintenance Brent V1300 / V1500 Auger Driveline (continued) 6. Remove universal joint covers from the driveshaft. Keep hardware and universal FIG. 4-31 joint covers. (Fig. 4-31) 7. Remove driveshaft lock collars (if lock col- lars are attached to driveshaft).
  • Page 94 — Maintenance Brent V1300 / V1500 Auger Driveline (continued) 15. Lift the driveshaft into the rear mounting FIG. 4-34 bracket. Attach the flangette bearings Driveshaft to the mounting brackets using new 1/2” Cover Driveshaft hardware. Tighten all flangette bearing hardware, but do not tighten lock collars at this time.
  • Page 95 — Maintenance Brent V1300 / V1500 Auger Driveline (continued) 21. Install new flangette bearing (9005061) onto Bottom FIG. 4-37 the front bracket mount under the right- View hand standard with the lock collar on the front side of the bracket mount toward the PTO.
  • Page 96 — Maintenance Brent V1300 / V1500 Auger Driveline (continued) 24. For alignment of the yoke, the orientation of the universal joint at the gearbox must Dimple Universal Joint be in line with the driveshaft drill dimple Orientaton in Line when the driveline assembly is attached.

  • Page 97: Adjusting Cleanout Door

    — Maintenance Brent V1300 / V1500 Adjusting Cleanout Door MOVING PARTS CAN CRUSH AND CUT. KEEP AWAY FROM MOVING PARTS. • KEEP HANDS CLEAR OF PINCH POINT AREAS. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT • MUST BE WORN WHILE SERVICING THE IMPLEMENT.
  • Page 98 — Maintenance Brent V1300 / V1500 Adjusting Cleanout Door (continued) 5. Push the gear assembly toward bottom of auger to remove excess movement and prevent the door from moving upward when Push Gear Assembly Toward Bottom of Auger unloading the cart. (Fig. 4-43) FIG.

  • Page 99: Verify Telescoping Pto Shaft Length

    — Maintenance Brent V1300 / V1500 Verify Telescoping PTO Shaft Length • PROPERLY EXTENDED AND COLLAPSED LENGTHS OF THE TELESCOPING PTO SHAFT MUST BE VERIFIED BEFORE FIRST OPERATION WITH EACH AND EVERY DIFFERENT TRACTOR. IF THE EXTENDED LENGTH OF THE PTO SHAFT IS NOT SUFFICIENT, IT...
  • Page 100 — Maintenance Brent V1300 / V1500 Verify Telescoping PTO Shaft Length (continued) 4. Hitch tractor drawbar to cart, ensuring that tractor and cart are on level ground and coupled as straight as practical. 5. Connect PTO shaft to tractor, and measure length “L” from same points as used in step 1. Ensure that this measurement does not exceed the maximum recommended extended length calculated in step 3 above.

  • Page 101: Pto Shaft And Clutch

    — Maintenance Brent V1300 / V1500 PTO Shaft and Clutch Coupling the PTO driveshaft (Figs. E1 - E2) Clean and grease the PTO and implement input connection (IIC) AS-Lock 1. Pull locking collar and simultaneously push PTO driveshaft onto PTO shaft until the locking device engages.
  • Page 102 — Maintenance Brent V1300 / V1500 PTO Shaft and Clutch (continued) To Dismantle Guard (Figs. J1 - J4) 1. Remove locking screw. 2. Align bearing tabs with cone pockets. 3. Remove half-guard. 4. Remove bearing ring. To Assemble Guard (Figs. K1 - K5) 1.
  • Page 103 — Maintenance Brent V1300 / V1500 PTO Shaft and Clutch (continued) To Assemble Cone (Figs. L1 - L3) 1. Dismantle guard (Figs. J1 - J3). move old cone (e.g. cut open with knife). Take off chain. Place neck of new cone in hot water (approx 80 F) and pull onto bearing housing (Fig.

  • Page 104: Pto Quick Disconnect

    Cône de serrage + (21) + (20) + (21) + (20) — Maintenance Brent V1300 / V1500 Best.-Nr. / Part No. / Référence Best.-Nr. / Part No. / Référence Best.-Nr. / Part No. / Référence Best.-Nr. / Part No. / Référence 107540 107542 48.5...
  • Page 105 — Maintenance Brent V1300 / V1500 Wheel, Hub and Spindle Disassembly and Assembly • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. BE SURE MACHINE IS SECURELY BLOCKED. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED.
  • Page 106 — Maintenance Brent V1300 / V1500 Wheel, Hub and Spindle Disassembly and Assembly (continued) 5. Inspect the spindle and replace if necessary. If spindle does not need to be replaced, skip to Step 6; otherwise continue with Step 5. Remove the bolt and lock nut that retains the spindle to the axle.

  • Page 107: Wheels And Tires - Wheel Nut Torque

    — Maintenance Brent V1300 / V1500 Wheels and Tires Wheel Nut Torque Requirements • IMPROPERLY TORQUED WHEEL NUTS/BOLTS CAN CAUSE A LOSS OF IMPLEMENT CONTROL AND MACHINE DAMAGE. TORQUE WHEEL NUTS/BOLTS TO VALUES IN TABLE. CHECK TORQUE BEFORE USE, AFTER ONE HOUR OF UNLOADED USE OR AFTER FIRST LOAD, AND EACH LOAD UNTIL WHEEL NUTS/BOLTS MAINTAIN TORQUE VALUE.

  • Page 108: Tire Pressure

    — Maintenance Brent V1300 / V1500 Wheels and Tires (continued) Tire Pressure The following is to be used as a general guide for tire inflation and figures can vary de- IT IS IMPORTANT THAT TIRES ARE INSPECTED pending on specific brand of tire used.
  • Page 109 — Maintenance Brent V1300 / V1500 Wheels and Tires (continued) Tire Pressure (continued) 4-39...

  • Page 110: Tire Warranty

    — Maintenance Brent V1300 / V1500 Wheels and Tires (continued) Tire Warranty For questions regarding new tire warranty, please contact your local original equipment tire USED TIRES CARRY NO WARRANTY. dealer. Following are phone numbers and Websites for your convenience: Firestone www.firestoneag.com...

  • Page 111: Seasonal Storage

    — Maintenance Brent V1300 / V1500 Seasonal Storage Your cart is an important investment. Spend a little time to protect it from destructive rust and corrosion. You will be repaid in longer service life and better performance. Do the following before placing the cart in storage: 1.

  • Page 112: Hydraulic Jack Cylinder Replacement

    — Maintenance Brent V1300 / V1500 Hydraulic Jack Cylinder Replacement • HIGH-PRESSURE FLUIDS CAN PENETRATE THE SKIN AND CAUSE SERIOUS INJURY OR DEATH. LEAKS OF HIGH-PRESSURE FLUIDS MAY NOT BE VISIBLE. USE CARD- BOARD OR WOOD TO DETECT LEAKS IN THE HYDRAULIC SYSTEM. SEEK MEDICAL TREATMENT IMMEDIATELY IF INJURED BY HIGH-PRESSURE FLUIDS.
  • Page 113 — Maintenance Brent V1300 / V1500 Hydraulic Jack Cylinder Replacement (continued) 9. Remove two 7/8"-9UNC x 2 1/4" capscrews (9390-165) and 7/8" lock washers (9404-037) FIG. 4-52 Jack Weldment 271712B from mounting bracket (273808B). (Fig. 4-52) (271712B) 10. Remove hydraulic jack assembly from the...

  • Page 114: Troubleshooting

    — Maintenance Brent V1300 / V1500 Troubleshooting Problem Possible Cause Corrective Action Check the connections to the main power harness in the tractor cab, and check the 5 AMP fuse in the fuse holder of the main Not getting 12 Volt power supply to power harness.
  • Page 115 — Maintenance Brent V1300 / V1500 Troubleshooting Problem Possible Cause Corrective Action 7 pin connector is not plugged Plug in 7 pin connector to same power source as the 5 function into tractor. controller. Proximity Switch at the auger Check power and ground to the proximity switch harness on the hinge is not getting Power or vertical auger.

  • Page 116: Tarp Troubleshooting Inspection & Maintenance

    — Maintenance Brent V1300 / V1500 Tarp Troubleshooting Inspection & Maintenance PROBLEM SOLUTION TARP SAGS IN MIDDLE AREAS BOWS MAY BE BENT OR ADJUSTED TOO LOW MISSING OR LOOSE RIDGE STRAP REPLACE OR RETIGHTEN TENSION MAY BE TOO LOOSE. U-JOINT MAY...

  • Page 117: Electrical System Diagram

    — Maintenance Brent V1300 / V1500 Electrical System Diagram To Right-Side of Right-Hand Side Cart Interior Tail Light RH Sub Assembly #280847 Work Light #9008957 Amber Light - Micro Dot #9006107 Red Tail/Turn Clearance Light Wiring Harness #9006282 #9007921 Rear Wiring...
  • Page 118 — Maintenance Brent V1300 / V1500 Electrical System Diagram — Plug #92450 GRAIN CART WIRES White - Ground Green - Right amber flashing lamp Yellow - Left amber flashing lamp Brown - Tail light Black - Interior & Auger Lights...
  • Page 119 — Maintenance Brent V1300 / V1500 Electric Over Hydraulic (EOH) System Schematic 4 Function Optional NOTE: The joystick and 7-pin connector MUST be plugged into the same power source. If plugged into different power sources, the spout rotate and auger fold functions WILL NOT operate normally.
  • Page 120 — Maintenance Brent V1300 / V1500 Electrical Diagram — Front Wiring Harness #9007911 4-50...
  • Page 121 — Maintenance Brent V1300 / V1500 Electrical Diagram — Rear Wiring Harness #9007913 4-51...
  • Page 122 — Maintenance Brent V1300 / V1500 Electrical Diagram — Auger Wiring Harness #9009077 4-52...
  • Page 123 — Maintenance Brent V1300 / V1500 Electrical Diagram — Clearance Wiring Harness #9007921 4-53...
  • Page 124 — Maintenance Brent V1300 / V1500 Electrical Diagram — Proximity Sensor #9007472 Electrical Schematic — Work Light #9008957 2 PIN INTEGRATED DEUTSCH CONNECTOR POWER (PIN #1) GROUND (PIN #2) 4-54...
  • Page 125 — Maintenance Brent V1300 / V1500 Electrical Diagram — Red Tail/Turn Light #9006282 Electrical Diagram — Amber Light - Round Side Marker #9006107 Electrical Diagram — Amber Lamp Double Face #9005142 4-55...
  • Page 126 — Maintenance Brent V1300 / V1500 EOH Valve Functions and Wire Locations 4 Spool (Optional) NOTE: For hydraulic connections chart, refer to “Hitching to Tractor - Hydraulic Connections” in the OPERATION section. PORT END OF CYLINDER FUNCTION BUTT END Flow Door CLOSE...
  • Page 127 — Maintenance Brent V1300 / V1500 Electrical System Schematic - Optional Wireless Electric Tarp 4-57...

  • Page 128: Hydraulic System Plumbing Diagram

    — Maintenance Brent V1300 / V1500 Hydraulic System Plumbing Diagram Spout Out Port B Port A Spout In Flow Door Closed Flow Door Stop Valve Flow Door Open Auger Raise Pilot Operated Check Valve Auger Lower Spout Tilt Out Spout Tilt In...
  • Page 129 — Maintenance Brent V1300 / V1500 Complete Torque Chart Capscrews - Grade 5 NOTE: • Grade 5 capscrews can be identified by three radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. • Tighten U-bolts evenly and equally to have the same number of threads exposed on each end.
  • Page 130 — Maintenance Brent V1300 / V1500 Complete Torque Chart Capscrews - Grade 8 NOTE: • Grade 8 capscrews can be identified by six radial dashes on the head. • For wheel torque requirements, refer to Wheels and Tires. • Tighten U-bolts evenly and equally to have the same number of threads exposed on each end.

  • Page 131: Hydraulic Fittings - Torque And Installation

    — Maintenance Brent V1300 / V1500 Hydraulic Fittings – Torque and Installation Tightening O-Ring Fittings 1. Ins pect c o mp o n e n t s f o r da m a g e o r O-Ring fittings contamination.
  • Page 132 — Maintenance Brent V1300 / V1500 Hydraulic Fittings – Torque and Installation Tightening JIC Fittings 1. Inspect all components for damage or contamination. Do not connect any other FIG. 4-50 JIC fittings type of fitting to a JIC fitting. 2. Lubricate the threads.
  • Page 133 Clean Out Door Assembly......................5-7 Flow Door Seals ........................5-8 Directional Spout........................5-10 Wheel Well Cover Kit (V1300 Only) ..................5-14 Wheel Well Cover Kit (V1500 Only) ..................5-15 Rear Ladder Components ......................5-16 Rear Access Door Components ....................5-17 Sideboards..........................

  • Page 134: Decals

    — Parts Brent V1300 / V1500 Decals Please visit www.unverferth.com/parts/ for the most current parts listing. 9008151 31 32...
  • Page 135 Decal, IMPORTANT “Flow Control Gate” 9003475 Decal, WARNING “PTO Cut & Crush” 9003474 Decal, DANGER “Electrical Lines” 9006360 Decal, Brent Logo - 5.5 x 43 9006361 Decal, Stripe - 2.73 x 36.50 95445 Decal, WARNING “High-Pressure” 95839 Decal, WARNING “Pinch Point”...

  • Page 136: Final Assembly

    — Parts Brent V1300 / V1500 Final Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 271887B CAT 5 Hitch Conversion Kit w/Scales Includes Items 5, 8, 9, 42 & 43 271893B CAT 5 Hitch Conversion Kit w/out Scales Includes Items 5, 8, 10, 42 &...
  • Page 137 — Parts Brent V1300 / V1500 Final Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 9007178 Jack 9004171 Jack Pin, 7/8” x 3 1/2” 288381B Driveshaft Cover Plate =Black= 9000140 Cable Tie 21 1/2”...

  • Page 138: Hopper Cross Brace Components

    — Parts Brent V1300 / V1500 Hopper Cross Brace Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 297772B For V1300 Cross Brace Weldment =Black= 297833B For V1500 9003397 Flange Nut 1/2”-13UNC 91266 Flange Screw 1/2”-13UNC x 1 1/2” Grade 5 9009602 Grommet 1 3/8”...

  • Page 139: Cleanout Door Assembly

    — Parts Brent V1300 / V1500 Cleanout Door Assembly Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 268312B Door Lift/Wheel Weldment =Black= 268313B Plate - Lock =Black= 268901 Door Lift/Shaft Weldment 286801 Pad - Wear...

  • Page 140: Flow Door Seals

    — Parts Brent V1300 / V1500 Flow Door Seals Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 292294 Seal - Poly 287073 Seal - Poly 281257G Spacer Bushing =Green= 281257R Spacer Bushing =Red=...
  • Page 141 — Parts Brent V1300 / V1500 Notes Please visit www.unverferth.com/parts/ for the most current parts listing.

  • Page 142: Directional Spout

    — Parts Brent V1300 / V1500 Directional Spout Please visit www.unverferth.com/parts/ for the most current parts listing. 5-10...
  • Page 143 — Parts Brent V1300 / V1500 Directional Spout Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 288946B Spout Assembly =Black= Includes Items 2-24 285290 Bushing-Sleeve 2.0625” Long 288947B Spout Weldment =Black= 290993 Shaft-Pivot 3/4” Dia. x 25 5/16”...
  • Page 144 — Parts Brent V1300 / V1500 Directional Spout (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES TA500309 Washer/Bushing 1 1/4” OD x 3/4” ID 288383B Hose Bracket Plate =Black= 272719 Gear Rack 272748 Pad-Pivot, 22 7/8”...
  • Page 145 — Parts Brent V1300 / V1500 Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 5-13...
  • Page 146 — Parts Brent V1300 / V1500 Wheel Well Cover Kit - Model V1500 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 294784G Wheel Well Cover Kit (Green) 294784R Wheel Well Cover Kit (Red) Includes Items 1 - 4...
  • Page 147 — Parts Brent V1300 / V1500 Wheel Well Cover Kit - Model V1300 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 288203G Wheel Well Cover Kit (Green) 288203R Wheel Well Cover Kit (Red) Includes Items 1 - 4...

  • Page 148: Rear Ladder Components

    — Parts Brent V1300 / V1500 Rear Ladder Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 297608B Upper Ladder Weldment =Black= 296429B Lower Ladder Weldment =Black= 900059 Draw Latch Keeper 900060 Draw Latch Handle 900066 Pin 3/16”...

  • Page 149: Rear Access Door Components

    — Parts Brent V1300 / V1500 Rear Access Door Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 256527R Rear Access Door Weldment =Red= 256527G Rear Access Door Weldment =Green= 256527BM Rear Access Door Weldment =Black Metallic=...

  • Page 150: Sideboards

    — Parts Brent V1300 / V1500 Sideboards Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. 5-18...
  • Page 151 — Parts Brent V1300 / V1500 Sideboards Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 220032B Tube, Angle Brace/Sideboard Support 39 7/8” =Black= 271574B...

  • Page 152: Single Wheel Axle (V1300 Only)

    — Parts Brent V1300 / V1500 Single Wheel Axle — For V1300 Only Please visit www.unverferth.com/parts/ for the most current parts listing. Direction of Travel 5-20...
  • Page 153 — Parts Brent V1300 / V1500 Single Wheel Axle — For V1300 Only Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 288191B Rigid Axle Assembly w/out Scales (Black) Includes Items 1, 2 & 3 through 28...

  • Page 154: Single Wheel Axle (V1500 Only)

    — Parts Brent V1300 / V1500 Single Wheel Axle — For V1500 Only Please visit www.unverferth.com/parts/ for the most current parts listing. Direction of Travel 5-22...
  • Page 155 — Parts Brent V1300 / V1500 Single Wheel Axle — For V1500 Only Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 294593B Rigid Axle Assembly w/out Scales =Black= Includes Items 1, 2 & 3 through 29...
  • Page 156 — Parts Brent V1300 / V1500 Track Axle — For V1300 Only Please visit www.unverferth.com/parts/ for the most current parts listing. FOR TRACK INFORMATION, PLEASE REFER TO YOUR TRACK MANUAL. Direction of Travel ITEM PART NUMBER DESCRIPTION NOTES 288193B Track Axle Assembly w/out Scales =Black=...
  • Page 157 — Parts Brent V1300 / V1500 Track Axle — For V1500 Only Please visit www.unverferth.com/parts/ for the most current parts listing. FOR TRACK INFORMATION, PLEASE REFER TO YOUR TRACK MANUAL. FOR TRACK INSTALL, PLEASE REFER TO TRACK INSTALLATION GUIDE CONE KIT - 267939.

  • Page 158: Driveline Components

    — Parts Brent V1300 / V1500 Driveline Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-26...
  • Page 159 — Parts Brent V1300 / V1500 Driveline Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 289819 Drive Shaft 1 3/4” Dia. x 144 5/8” 293380 Tube Cover 52” Long 288762 Tube Cover 41 1/2” Long...

  • Page 160: Driveline U-Joint Assembly

    — Parts Brent V1300 / V1500 Driveline U-Joint Assembly For SN B45970100 and Higher Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 9010019 Complete Double U-Joint Assembly 9010012 Yoke 1 3/4”-20 Spline with Conic Bolt...
  • Page 161 — Parts Brent V1300 / V1500 Driveline U-Joint Assembly For SN B45970099 and Lower Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 9007886 Complete U-Joint Assembly 9007829 Yoke 1 3/4-20 Spline with Interference Clamp Connection...

  • Page 162: Single Wheels And Tires

    — Parts Brent V1300 / V1500 Single Wheels & Tires Please visit www.unverferth.com/parts/ for the most current parts listing. TIRES For questions regarding new tire warranty, please contact your lo- cal original equipment tire dealer. Used tires carry no warranty.
  • Page 163 — Parts Brent V1300 / V1500 Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 5-31...

  • Page 164: Upper Auger Components

    — Parts Brent V1300 / V1500 Upper Auger Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-32...
  • Page 165 — Parts Brent V1300 / V1500 Upper Auger Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 288899G Upper Auger Housing Replacement Kit =Green= 288899R Upper Auger Housing Replacement Kit =Red= 288899BM Upper Auger Housing Replacement Kit =Black Metallic=...

  • Page 166: Lower Auger Components

    — Parts Brent V1300 / V1500 Lower Auger Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-34...
  • Page 167 — Parts Brent V1300 / V1500 Lower Auger Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 291825B Lower Auger Replacement Kit =Black= Includes Lower Auger and Items 2-4 Replacement kit #296456B 296457B Lower Auger Extension Plate =Black=...

  • Page 168: Pto Cut Out Clutch Components (Benzi America)

    — Parts Brent V1300 / V1500 PTO Cut Out Clutch Components (Benzi America) Please visit www.unverferth.com/parts/ for the most current parts listing. For Benzi PTO Components, U-Joint Color is Gray. NOTE: Clutch Assembly (9009780) Must be used with the complete PTO Assembly (9009527).

  • Page 169: Pto Components (Benzi America)

    — Parts Brent V1300 / V1500 PTO Components (Benzi America) Please visit www.unverferth.com/parts/ for the most current parts listing. For Benzi PTO Components, U-Joint Color is Gray. ITEM PART NO. DESCRIPTION NOTES 9009527 PTO Assembly Complete Includes items 1 and 2...

  • Page 170: 45 Degree Gearbox

    — Parts Brent V1300 / V1500 45 Degree Gearbox Please visit www.unverferth.com/parts/ for the most current parts listing. 5-38...
  • Page 171 — Parts Brent V1300 / V1500 45 Degree Gearbox Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 9008711 Gearbox 45° Q135 Series, Complete Includes Items 1 through 20 9007488 Bearing Cup/Cone, 3.15” OD x 1.772” ID 9007507 Bearing Cone, 2 1/4”...

  • Page 172: Cylinders

    1 3/4 ROD DIA. — Parts Brent V1300 / V1500 0.75 REF 0.69 REF Cylinders — 4” x 24” (Auger Fold) 1.125 Please visit www.unverferth.com/parts/ for the most current parts listing. 1.120 ITEM PART NUMBER DESCRIPTION QTY. NOTES 9007786 Welded Cylinder, Complete...
  • Page 173 — Parts Brent V1300 / V1500 Cylinders — 3 1/2” x 8” (Optional Hydraulic Jack) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION QTY. NOTES 9009047 Welded Cylinder, Complete 9007880 Seal Kit 5-41...

  • Page 174: Hydraulics

    — Parts Brent V1300 / V1500 Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. Port B Spout Rotate Rear Port A Spout Rotate Front Flow Door Closed Flow Door Open Auger Raise Auger Lower Spout Tilt Out Spout Tilt In...
  • Page 175 — Parts Brent V1300 / V1500 Hydraulics Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 97405 Hose 1/4” x 74” (9/16”-18 JIC Female x 9/16”-18 JIC Female) 9001495 Adapter (9/16”-18 JIC Male x 9/16”-18 O-Ring Male) 9001710 Tee (9/16”-18 JIC M x 9/16”-18 O-Ring M x 9/16”-18 JIC M)
  • Page 176 — Parts Brent V1300 / V1500 Hydraulics (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9000104 Cable Tie 21 1/2” 9000106 Cable Tie 7 1/2” 9000107 Cable Tie 14 1/2” 9003814 Top Plate...
  • Page 177 — Parts Brent V1300 / V1500 EOH Tractor Circuit Hydraulic Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. CHECK VALVE MUST BE ASSEMBLED AS SHOWN ITEM PART NO. DESCRIPTION QTY. NOTES 9002283 Hydraulic Hose, 1/2 x 184” - 3000 PSI 9007842 Hydraulic Hose, 1/4 x 172”...

  • Page 178: Eoh Valve Assembly Components 4 Spool (Optional)

    — Parts Brent V1300 / V1500 EOH Valve Assembly Components 4 Spool (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. Cartridge Valve Incorrect Top (9008416) Detent Position Correct Middle...
  • Page 179 — Parts Brent V1300 / V1500 EOH Valve Assembly Components 4 Spool (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES Cartridge Valve - 4 Way, 3 Position - Closed Center...

  • Page 180: Electrical

    — Parts Brent V1300 / V1500 Electrical Please visit www.unverferth.com/parts/ for the most current parts listing. Right-Hand Side To Right-Side of Cart Interior Joystick Parts To Tractor Left-Hand Side To Directional Spout 5-48...
  • Page 181 — Parts Brent V1300 / V1500 Electrical Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 9007911 Wiring Harness, Front 280847 Tail Light RH Sub Assembly Includes Items 3A, 4 through 12, 13A, 14 280848...

  • Page 182: Weather Guard Tarp

    — Parts Brent V1300 / V1500 Weather Guard Tarp Please visit www.unverferth.com/parts/ for the most current parts listing. 5-50...
  • Page 183 — Parts Brent V1300 / V1500 Weather Guard Tarp Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 91263 Flange Nut 3/8”-16UNC 9009089 Machine Screw 3/8”-16UNC x 1 1/4” 9003078 Plastic Cap 3/16”x2”x3” 9004548 Eye Bolt 3/8”-16UNC x 1 3/4”...
  • Page 184 Flange Screw 5/16”-18UNC x 1” Grade 5 296129B End Cap Weldment - Front - Long =Black= For V1300 For V1300 Includes End Cap 296757B End Cap Weldment - Front - Long - Service Kit & Items 11 & 45 296142B...

  • Page 185: Video System Option

    — Parts Brent V1300 / V1500 Video System Option Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 265770 Video System Kit for Front View Includes Items 1,3,4,5,6,7,8 9004506 Additional Camera for Rear View Includes Items 6 & 7...

  • Page 186: Hydraulic Jack- Kit #294143B (Optional)

    — Parts Brent V1300 / V1500 Hydraulic Jack - Kit #294143B (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 271712B Jack Weldment =Black= 271723B Jack Foot Weldment =Black= 273808B Jack Mount Weldment =Black= 9009047 Hydraulic Cylinder 3 1/2”...
  • Page 187 — Parts Brent V1300 / V1500 Notes Please visit www.unverferth.com/parts/ for the most current parts listing. 5-55...
  • Page 188 www.unverferth.com MANUALS\\297936//October 2024-0...

This manual is also suitable for:

V1500

Table of Contents