I-Tech WMPC1900i5-C1D2-V3 User Manual
  1. Manuals
  2. Brands
  3. I-Tech Manuals
  4. Touch Panel
  5. WMPC1900i5-C1D2-V3
  6. User manual
I-Tech WMPC1900i5-C1D2-V3 User Manual

I-Tech WMPC1900i5-C1D2-V3 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WMPC1900i5-C1D2-V3
User's Manual
Version V 1.7
Copyright  2023, ALL RIGHTS RESERVED.
All other brand names are registered trademarks of their respective owner
i-Tech Company LLC
EMAIL: info@i-techcompany.com • WEB: www.iTechLCD.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WMPC1900i5-C1D2-V3 and is the answer not in the manual?

Questions and answers

Related Manuals for I-Tech WMPC1900i5-C1D2-V3

Summary of Contents for I-Tech WMPC1900i5-C1D2-V3

  • Page 1 WMPC1900i5-C1D2-V3 User’s Manual Version V 1.7 Copyright  2023, ALL RIGHTS RESERVED. All other brand names are registered trademarks of their respective owner i-Tech Company LLC EMAIL: info@i-techcompany.com • WEB: www.iTechLCD.com...
  • Page 2 Acknowledgments Greeting & Setup Thank you for purchasing the WMPC1900i5-C1D2-V3 Panel PC. We wish that this unit will be durable and reliable in providing your needs. Please follow the instructions below to ensure the unit continues to have high performance Unpacking After opening the carton, there will be a unit with an accessory box.
  • Page 3 Unless proper ventilation is present, do not place unit in an enclosed area; such as a built-in shelf. Keep a minimum distance of 10 cm between the display unit and wall. Cleaning the unit Remember to turn off the power source and to unplug the cord from the outlet before cleaning the unit. Carefully dismount the unit or bring the unit down from suspension to clean.
  • Page 4 Original and Configuration A: COM1: Uo = 10.0 V, Io = 38.9 mA, Po = 389 mW Co = 2.8 µF, Lo = 52.867 mH COM2: Uo = 9.0 V, Io = 31.6 mA, Po = 284 mW Co = 0.3 µF, Lo = 80.115 mH Configuration B/C: COM: Uo = 9.0 V, Io = 31.6 mA, Po = 284 mW...
  • Page 5 Version Change History Date Version Description Remark 2018/02/15 V1.0 First release 2019/08/26 V1.1 Remove cables installation guide 2020/10/14 V1.2 Add EU DoC 2021/01/22 V1.3 Update new ISO board and USB receiver information and cable installation guide, delete NEMA X4, add description: - Do not power the device before installation is complete.

  • Page 6: Table Of Contents

    How to Use This Manual ............. 6 Specifications ............7 System View ............13 WMPC1900i5-C1D2-V3 Outline Drawing ........13 WMPC1900i5-C1D2-V3 I/O Port description ......14 DC Power Cable Assembly Method ...... 17 USB Cable Assembly Method ....... 19 COM Cable Assembly Method ......21 LAN Cable Assembly Method .......

  • Page 7: How To Use This Manual

    This manual is written for the system integrator, PC technician and knowledgeable PC end user. It describes how to configure your WMPC1900i5-C1D2-V3 Panel PC to meet various operating requirements. The user’s manual is divided into three chapters, with each chapter addressing a basic concept and operation of the server board.

  • Page 8: Specifications

    Specifications System FCBGA1356 6th generation Intel® Core i7/i5/i3 processor (15W max.) Chipset Graphic Intel® integrated HD Graphics 520 Audio Realtek ALC262 Audio Codec, 2+2 watts power amplifier Intel i219LM x 1 (vPro not default, supported by specific CPU) + i210AT x 1 Memory Two 2133 MHz DDR4 SODIMM socket support dual Channel, non-ECC Generates system reset;...
  • Page 9 External I/O Original Cable Gland M16 Connector (Max. I.O.X 4) Unused openings Swappable M12 Connector (I.S. Outputs): RS-232 x2, 8pin (with extension cable to connect EX ic device) ATEX Entity parameters: COM1: Uo = 10.0 V, Io = 38.9 mA, Po = 389 mW, Co = 2.8 μF, Lo = 52.867 mH COM2: Uo = 9.0 V, Io = 31.6 mA, Po = 284 mW, Co = 0.3 μF, Lo = 80.115 mH C1D2/C2D2 Non-incendive Field Wiring Parameters: COM1: Uoc = 10.0 V, Isc = 38.9 mA, Po = 389 mW, Ca = 2.8 µF, La = 52.867 mH...
  • Page 10 Installation definition Configuration B/C Cable Gland M16 Connector (Max. I.O. X 4) (cable kit must be installed by user) USB2.0x2, ports can be easily connected by opening connector panel (EX ec solution) Gigabit Ethernet LANx2, ports can be easily connected by opening connector panel (EX ec solution) RS-232/422/485x1, port can be easily connected by opening connector panel (EX ec solution)
  • Page 11 Installation definition Configuration D Cable Gland M16 Connector (Max. I.O. X 4) (cable kit must be installed by user) USB2.0x2, ports can be easily connected by opening connector panel (EX ec solution) Gigabit Ethernet LANx2, ports can be easily connected by opening connector panel (EX ec solution) RS-232/422/485x1, port can be easily connected by opening connector panel (EX ec solution)
  • Page 12 Installation definition Power AC-DC power adapter: 100-240V AC-DC power adapter with 24V DC output (Class III earthed SELV), 1.2M cable, power supply unit with PSE mark Power Input DC24V Power consumption 46.7 watt Power connector cable gland M16 Connector x 1, (EX ec solution) (cable kit must be installed by user) Mechanical &...
  • Page 13 Connector panel for easy USB and LAN cable installation Ventilation connector Packing list 1. WMPC1900i5-C1D2-V3 x 1 2. DVD-Title for driver and manual x 1 3. 100-240V AC-DC power adapter with 24V DC output (Class III earthed SELV), 1.2 meter DC cable length x 1 4.

  • Page 14: System View

    Configuration WMPC1900i5-C1D2-V3, Core i5-6200U CPU, 2.30GHz, 4G RAM, 128SSD Operation system Windows Embedded Standard 7 32/64-bit Windows 7 Professional 32/64-bit Win10 Embedded 64-bit Windows 10 Professional 64-bit System View WMPC1900i5-C1D2-V3 Outline Drawing Front view Side and Rear View (ATEX / C1D2 / C2D2)

  • Page 15: Wmpc1900I5-C1D2-V3 I/O Port Description

    Configuration A, B, C and D (ATEX / C1D2 / C2D2) WMPC1900i5-C1D2-V3 I/O Port description Original (ATEX / C1D2 / C2D2)
  • Page 16 I/O ports Description Please refer to the DC Power Cable Assembly Method DC in (i.e. Ex “e” Cable Gland ) COM ports RS-232 cable connecting to device ( Ex ic ) Earth ground Always ground yourself against electrostatic damage to the device Locking plugs Unused in hazardous location ( "Ex e"...
  • Page 17 COM2 RS-232 cable connecting to device ( Ex ic ) Configuration B/C USB cable connecting to device ( Ex ic ) USB cable connecting to device ( Ex ic ) Configuration D USB cable connecting to device ( Ex ic ) Earth ground Always ground yourself against electrostatic damage to the device Port 1...

  • Page 18: Dc Power Cable Assembly Method

    DC Power Cable Assembly Method Note: If install 50m & 100m DC power cable, please repeat the above steps Step 1: Remove the back cover plate. Step 2: Put the cable through cable glands in sequence like showing below. Step 3: DC_IN housing need to follow cable pin assignment installation.
  • Page 19 Step 4: The power cable_Housing install to PJ5, refer Jumper settings and Connectors in User Manual. Step 5: Tighten the cable gland and screw the back cover plate. Note: (1) Cable glands Torque value is 6 N•m (2) M12 connector Torque value is 6 kgf-cm (3) M3 screw Torque value is 6 kgf-cm...

  • Page 20: Usb Cable Assembly Method

    USB Cable Assembly Method Step 1: Remove the back cover plate. Step 2: Put the cable through cable glands in sequence like showing below. Step 3: The Housing need to follow cable pin assignment installation.
  • Page 21 Step 4: The USB cable install to J48/J49, refer Jumper settings and Connectors in User Manual. Step 5: Tighten the cable gland and screw the back cover plate. Note: (1) Cable glands Torque value is 6 N•m (2) M12 connector Torque value is 6 kgf-cm (3) M3 screw Torque value is 6 kgf-cm...

  • Page 22: Com Cable Assembly Method

    COM Cable Assembly Method Step 1: Remove the back cover plate. Step 2: Put the cable through cable glands in sequence like showing below.
  • Page 23 Step 3: The Housing need to follow cable pin assignment installation. Step 4: The COM cable install to J51, refer Jumper settings and Connectors in User Manual.
  • Page 24 Step 5: Tighten the cable gland and screw the back cover plate. Note: (1) Cable glands Torque value is 6 N•m (2) M12 connector Torque value is 6 kgf-cm (3) M3 screw Torque value is 6 kgf-cm...

  • Page 25: Lan Cable Assembly Method

    LAN Cable Assembly Method Step 1: Remove the back cover plate. Step 2: Put the cable through cable glands in sequence like showing below and follow cable pin assignment and crimping tool installation.
  • Page 27 Step 3: LAN cable install to J42, refer Jumper settings and Connectors in User Manual. Step 4: Tighten the cable gland and screw the back cover plate. Note: (1) Cable glands Torque value is 6 N•m (2) M12 connector Torque value is 6 kgf-cm (3) M3 screw Torque value is 6 kgf-cm...

  • Page 28: Bios Setup Information

    BIOS Setup Information BIOS Introduction The AMI BIOS (Basic Input / Output System) installed in your computer system’s ROM supports Intel processors. The BIOS provides critical low-level support for a standard device such as disk drives, serial ports and parallel ports. It also adds virus and password protection as well as special support for detailed fine-tuning of the chipset controlling the entire system.
  • Page 29 Advanced Intel(R) I210 Gigabit Network connection Configure Gigabit Ethernet device parameters Intel(R) Ethernet Connection I219-LM Configure Gigabit Ethernet device parameters driver Health Provides Health status for the Drivers/Controllers Trusted Computing Configuration Enables or disables BIOS support for security device. O.S. will not show Security Device.
  • Page 30 OEMFLag Bit 2:Enable/Disable MEBx selection screen. Hide Un-Configure ME Confirmation Prompt OEMFlag Bit 6:Hide Un-Configure ME without password Confirmation Prompt. Un-Configure ME OEMFlag Bit 15:Un-Configure ME without password. Serial Port Configuration Serial Port 1 Configuration Serial Port Select an optimal settings for super IO Device. Change Settings Select an optimal settings for Super IO Device.
  • Page 31 Enable or disable System wake on alarm event. Select FixedTime, System will wake on the hr::min::sec specified. Select DynamicTime , System will wake on the current time + Increase minute(s). CPU Configuration CPU Configuration Parameters Active Processor Cores Number of cores to enable in each processor package. Intel Virtualization Technology When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool...
  • Page 32 SATA DEVSLEP Idle Timeout config Enable/Disable SATA DTIO Config Serial-ATA Port 1 Enable / Disable Serial ATA Port 0. Port 0 Enable or Disable SATA Port HotPlug Designates this port as hot Pluggable. External SATA External SATA Support Spin Up Device On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device.
  • Page 33 SATA DEVSLEP Idle Timeout config Enable/Disable SATA DTIO Config Info Report Configuration Post Report Post Repost Support Enabled / Disabled. Info Error Message Info Error Message Support Enabled / Disabled. Summary Screen Summary Screen Support Enabled / Disabled. USB Configuration USB Support USB Support Parameters.
  • Page 34 Chipset System Agent (SA) Configuration System Agent (SA) Parameters. VT-d VT-d capability Graphics Configuration Graphics Turbo IMON Current Graphics Turbo IMON current values supported(14-31) Skip Scaning of External Gfx Card If Enable, it will not scan for external Gfx Card on PEG and PCH PCIE Ports Primary Display Select which of IGFX/PEG/PCI Graphics device should be Primary Display or Select SG for Switchable GFX.
  • Page 35 PCI Express Configuration settings USB Configuration USB Precondition Precondition work on USB host controller and root ports for faster enumeration. PCI Express Configuration settings XHCI Disable Compliance Mode Options to disable Compliance Mode. Default is FALSE to not disable Compliance Mode. Set TRUE to disable Compliance Mode.
  • Page 36 Security Administrator Password Set Administrator Password. User Password Set user Password. P3：TS64GSSD370 HDD Security Configuration for selected drive. Secure Boot menu Secure Boot Secure Boot can be enabled if 1.System running in User mode with enrolled Platform key(PK). 2. CSM function is disabled. Secure Boot Mode Secure Boot mode selector.
  • Page 37 Boot Setup Prompt Timeout Number of seconds to wait for setup activation key. 65535(0xFFFF) means indefinite waiting. Bootup Numlock State Selects the keyboard NumLock state. PXE Boot PXE Network Boot Enable / Disable. Quiet Boot Enable or disables Quiet Boot option. Boot Option #1 Sets the system boot order.
  • Page 38 Save Changes and Exit Exit system setup after saving the changes. Discard Changes and Exit Exit system setup without saving any changes. Save Changes and Reset Reset the system after saving the changes. Discard Changes and Reset Reset system setup without saving the changes. Save Changes Save the changes done so far to any of setup options.

  • Page 39: Appendix

    Appendix A. Jumper settings and Connectors This appendix gives the definitions and shows the positions of jumpers, headers and connectors. All of the configuration jumpers on WMPC1900i5-C1D2-V3 are in the proper position.  Jumper and Connector Definition Block Note: (1) connectors not mounted:...
  • Page 40  JP1 – Touch Panel Type Selection Description Jumper Setting 3M type 1-2, 3-4 (default) ELO type 5-6,7-8  JP2 – PCT/RES Touch Selection Description Jumper Setting PCT Touch RES Touch  JP3 –TPM2.0 Pin # Signal Description Pin # Signal Description DEBUG_CLK LPC_FRAME#...
  • Page 41  JP6 – Sensor Selection Description Jumper Setting No Panel Sensor 1-2(default) No MB Sensor 3-4(default) Reserved  JP7 –Panel Resolution Selection  JP8 – Backlight control level Selection Description Jumper Setting +3.3V OPEN (default)  JP9 – Heater Test Selection Description Jumper Setting Normal...
  • Page 42  JP14 – RTC Register Clear Selection Description Jumper Setting Normal Open (default) RTC Register Clear  JP15 – SATA / SATADOM Selection Description Jumper Setting SATA 2-3(default) SATA DOM  JP16 – COM1 RI# / 12VS / 5VS Selection Description Jumper Setting 12VS...

  • Page 43: Connector Definition

    1.1 Connector Definition  PJ1 /PJ2 – HDD Power Connector Pin # Signal Description +12VS +5VS  PJ5 – Power Input Connector Pin # Signal Description DC In DC In  J1, J48, J49 – Internal USB 2.0 Pin Header Pin # Signal Description +5VSB...
  • Page 44  J2 – LCD Inverter Wafer Header Pin # Signal Description +12VS +12VS Backlight Control Backlight Enable  J3 – MB Heater Connector Pin # Signal Description +12VSB  J8 – Internal USB 2.0 Pin Header for Webcam Pin # Signal Description +5VSB +5VSB...
  • Page 45  J10 – Resistance Touch Screen Interface Signal Description Pin # 8-wire 4-wire 5-wire UL(X+) UL(X+) UL(X+) UR(Y+) UR(Y+) UR(Y+) PROBE LR(X-) LR(X-) LR(X-) LL(Y-) LL(Y-) LL(Y-) X+_DRIVE Y+_DRIVE X-_DRIVE Y-_DRIVE  J11 – LVDS Interface Pin # Signal Description Pin # Signal Description Ground...
  • Page 46  J12 – Panel Temp Sensor Connector Pin # Signal Description PANEL_SENSOR  J13 – 80 Port Pin # Signal Description Pin # Signal Description LPC_AD0 +5VS LPC_AD1 +3.3VS LPC_AD2 L80HLAT LPC_AD3 L80LLAT  J14 – M.2 E_Key Pin # Signal Description Pin # Signal Description...
  • Page 47 CLKREQ0#(I/O)(0/3.3V) BT_DISABLE2#(I)(0/3.3V) PEWAKE0#(I/O)(0/3.3V) W_DISABLE1#(I)(0/3.3V) RSVD RSVD RSVD +3.3V +3.3V  J16 – Light Sensor Connect Pin # Signal Description +3.3VS Ground SMBCLK LIG_SEN_INT# SMBDATA  J17 –TPM / ID-394 Pin # Signal Description Pin # Signal Description +3.3VSB SUS_STAT# SMB DATA SMB CLK Debug CLK CLKRUN#...
  • Page 48  J20 / J21 – DDR4 SO-DIMM Interface J20 H5.2mm J21 H9.2mm...
  • Page 49  J25 – Battery Socket  J26 – JTAG For EC Pin # Signal Description Pin # Signal Description Reserved Reserved +3.3V Reserved +3.3V +3.3V  J27 – Mini PCI Express / mSATA Socket Pin # Signal Description Pin # Signal Description WAKE# +3.3VSB...
  • Page 50  J28 – Standard SATA / SATA DOM Interface Pin # Signal Description Ground Ground Ground / +5VS  J29 – BIOS Socket Pin # Signal Description Pin # Signal Description CS0# MOSI MISO SCLK HOLD +3.3VS  J30 – Standard SATA Interface Pin # Signal Description Ground...
  • Page 51 +5VSB +3.3VSB KP_SCL KP_SDA PWR_LED# KP_P_LED SATA_LED#  J36 – Internal COM5 Serial Port Pin # Signal Description Pin # Signal Description 232_DSR# 232_DCD# 232_RTS# 232_SIN 232_CTS# 232_SOUT 232_RI# 232_DTR# +5VS  J37 – Internal COM4 Serial Port Pin # Signal Description Pin # Signal Description...
  • Page 52 Pin # Signal Description Pin # Signal Description 232_DSR# 232_DCD# 232_RTS# 232_SIN 232_CTS# 232_SOUT 232_RI# 232_DTR# +5VS  J40 – Power / HDD LED Pin # Signal Description SATA_LED# +3.3VSB +3.3VSB PWR_LED#  J41 – Internal COM6 Serial Port Pin # Signal Description Pin # Signal Description...

  • Page 53: Eu Declaration

    Pin # Signal Description Pin # Signal Description 232_DSR# 232_DCD# 232_RTS# 232_SIN 232_CTS# 232_SOUT 232_RI# 232_DTR# +5VS/+12VS  J51 – Internal COM1 Serial Port Pin # Signal Description Pin # Signal Description 232_DSR# 232_DCD# 232_RTS# 232_SIN 232_CTS# 232_SOUT 232_RI# 232_DTR# +5VS/+12VS ...

Table of Contents