Page 44
Use an Universal Disassembly ESD stick or Deglue Machine ● ● Pixel 6 Cleaning Cover CG and place the cover. to clean the residual glue out of the Display. Use an Deglue Machine to clean the residual glue out of the ●...
Page 46
04. Adhesive alignment 05. Enclosure to adhesive Place the adhesive in the Pixel 6 Enclosure PSA Align & Vertically place the Enclosure into the pocket in the indicated ● ● Press Cover with the ESD tweezers. direction. Do not touch the adhesive. If it gets dirty, change for another one.
Page 47
07. Remove Enclosure Do Not press on RCAM Area(Visor). Gently press the all around adhesive by hands, to enhance Remove the Enclosure from the Pixel 6 Enclosure PSA Align & ● ● the bonding between Enclosure and adhesive. Press Cover vertically.
Page 48
08. Adhesive to enclosure 09. Remove the liner (1st layer) Pick up the tab here Place the Enclosure in the Pixel 6 Enclosure Holder & Slowly pull the liner to avoid lifting the adhesive, with the pull ● ● Graphite Align.
Page 49
10. Place the press cover 11. Press together in fixture Place the Pixel 6 Enclosure PSA Align & Press Cover ON Place on the Universal press fixture and press the handle ● ● TOP OF Pixel 6 Enclosure Holder & Graphite Align.
Page 55
23. Place in holder 22. Place in holder Place it in the Universal press fixture and press the handle Place the device in the Pixel 6 Enclosure Holder & Graphite ● ● down for 30 seconds. Align and place the Press cover on top.
Page 60
01. Apply SPACER Battery 02. Adhere SPACER Battery With the device in the Pixel 6 Enclosure Holder & Graphite Use the Universal Scraper and roll the SPACER Battery. ● ● Ensure there are no air pockets. Use the smaller scraper where Align, place the SPACER Battery, aligning with the the needed.
Page 61
03. Apply graphite sheet 04. Adhere graphite sheet With the device in the Pixel 6 Enclosure Holder & Graphite Use the Universal Scraper and roll the bottom graphite sheet. ● ● Ensure there are no air pockets. Use the smaller scraper where Align, place the Graphite sheet, aligning with the the needed.
Page 63
07. Remove the liner 08. Attach the sponges Remove the release liner. Align two sponges by the alignment Pins of Pixel 6 Enclosure ● ● and CG Press Cover & Sponge Align. Press the sponges by Universal Disassembly ESD stick.
Page 64
09. Attach the sponges (mid-frame) Align by the outline of the mid-frame. Align two sponges by the alignment Pins of Pixel 6 ● Enclosure and CG Press Cover & Sponge Align. Press the sponges by Universal Disassembly ESD stick. ●...
01. Screw cover 02. Remove screws Remove 9 Mid-frame Screws with a Torx Plus 3IP screwdriver. Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure ● ● Holder & Graphite Align. The 3 alignment pins are to avoid Then remove the Pixel 6 Screw Cover.
Page 71
03. Fitting the Mid-frame 04. Fasten the Mid-frame Assemble the Mid-frame according to the positioning posts Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure ● ● Holder & Graphite Align. on the Logic board. Tighten the 7 Screws with a Torx Plus 3IP screwdriver, take Part: G949-00186-01 (Mid-frame_mmWave) ●...
Page 76
03. Remove Screws 04. Remove bracket Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Remove the bracket with an Universal Disassembly ESD ● ● Holder & Graphite Align. stick. Remove the mmWave bracket screw with a Torx Plus 3IP ●...
Page 80
03. Assemble Sub-6 Foam 04. Assemble bracket Insert the bracket at an angle into the Enclosure. Place Pixel 6 Screw Cover on the Pixel 6 Enclosure Holder & ● ● Graphite Align. Fasten the mmWave bracket screw with a Torx Plus (3IP), ●...
Page 89
01. Remove screws 02. Remove rear camera Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Loosen 2 Rear camera connectors and disconnect from the ● ● Holder & Graphite Align. Logic board with a Universal Fish line tool.
Page 93
Attach the 2 connectors to the Logic board, applying pressure ● Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Holder ● evenly across the connectors to ensure they are fully engaged. & Graphite Align.
Page 97
01. Remove screws 02. Remove Bottom speaker Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Remove the Bottom speaker with an ESD tweezers. ● ● Holder & Graphite Align. Remove the five Bottom speaker screws with a Torx Plus ●...
Page 99
01. Attach bottom Speaker 02. Fasten the screw Before assembling, check whether the foam is off, or broken. Place Pixel 6 Screw Cover on the Pixel 6 Enclosure Holder & ● ● Insert the Bottom speaker at an angle to slot into the Graphite Align.
Page 106
01. Soften glue 02. Lift up pull jacket Place the device flat on the Heat plate and set to 158℉/70 ℃ With the device in the Pixel 6 Enclosure Holder & Graphite ● ● for 10 mins to soften the Battery adhesive equally.
Page 111
Align the Battery at the corners as the figure circles, using the ● Place the Pixel 6 Battery Press on the Pixel 6 Enclosure feeler gauge. (Fig1.) ● Holder & Graphite Align. Gently press the Battery down with the Universal adsorption ●...
Page 112
05. Press together in fixture 06. Press together in fixture Place the Pixel 6 Enclosure Holder & Graphite Align in the Return the handle to the original position and remove the Pixel ● ● Universal press fixture. 6 Enclosure Holder & Graphite Align.
01. Remove SIM tray 02. Remove the screw Remove the SIM tray with a Universal Fish line tool. Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Holder ● ● & Graphite Align. Remove the Logic board screw with a Torx Plus 3IP ●...
Page 125
09. Screw in logic board 10. Attach connectors Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Attach the side-key connector to the Logic board. ● ● Holder & Graphite Align. Tighten the screw with a Torx Plus (3IP) screwdriver, as ●...
Page 134
01.Remove screws 02. Remove Top Speaker Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure Remove the Top speaker with an Universal Disassembly ESD ● ● Holder & Graphite Align. stick. Remove the Top speaker screws with a Torx Plus 3IP ●...
Page 137
03. Fasten top speaker Place the Pixel 6 Screw Cover on the Pixel 6 Enclosure ● Holder & Graphite Align. Tighten the Top speaker screw with a Torx Plus 3IP ● screwdriver, then remove the Pixel 6 Screw Cover. Torque force : 1.4 ± 0.03kgf-cm...
Page 142
Visually check the WC&NFC flex pad, make sure it is not covered/obstructed by the ● graphite sheet or other components, and the Flex tail align on enclosure edge (Fig I) If you see flex not in right position like Fig II, please contact your google ● representative.
Need help?
Do you have a question about the Pixel 6 and is the answer not in the manual?
Questions and answers