Page 1
AC-EX150-BKT User Manual AC-EX150-BKT 150 m 1080p (100 m 4K) HDBaseT Extender w/ 4K60 support. Bi-DirecBonal PoE, IR, and RS232. Model Numbers: AC-EX150-BT ~ HDBaseT Transmi9er w/IR and RS-232 AC-EX150-BR ~ HDBaseT Receiver w/ IR and RS-232 Page 1...
AVPro Edge presents the quick-deployment 4K HDBaseT Extender Set. This set can deliver 4K signals over Category cable up to 100 meters (330 S) and Full HD signals up to 150 meters (492S). The AC-EX150-BKT features field-criYcal features, including Bi-DirecYonal PoH (Power Over HDBaseT) and Bi-DirecYonal RS232 for control.
AC-EX150-BKT Transmi>er Front Back Indicator Troubleshoo6ng LEDs on the Transmi;er: POWER - On the front at the power supply input: (Blue). This indicates power is connected. There are only two states for LED: LED Is On = Power supply is connected and funcYoning •...
Page 7
AC-EX150-BKT LINK - At the RJ45 (HDBaseT) Port: (Green) Indicates the AV HDBaseT link between Tx and Rx is intact. This LED should ALWAYS remain solid. If this LED is flashing or not present, verify the following: Category cable length. The maximum distances are 100 m (330 S.) at 4K and 150 m (492 S.) at 1080p.
AC-EX150-BKT Func%ons & Setup of the Transmi5er EDID Management With DIP switches on the bottom of the Transmitter The first 3 are used to set the EDID · ON/UP/1 · OFF/DOWN/0 EDID SETTINGS JUMPER BYPASS (HDBT) 1080P_2CH 1080P_8CH 4K 60Hz YC420_3D_2CH...
AC-EX150-BKT Receiver Front Back Indicator Troubleshoo6ng LEDs on the Receiver: POWER - On the front at the power supply input: (Blue). This indicates power is connected. There are only two states for LED: LED Is On = Power supply is connected and funcYoning •...
AC-EX150-BKT Use a 2-meter or longer HDMI cable. HDMI cables oSen fail to reliably sync in shorter lengths. Contact AVPro Edge Technical Support if these suggesYons do not work LINK - At the RJ45 (HDBaseT) Port: (Green) Indicates the AV HDBaseT link between Tx and Rx is intact.
From Rack (Using an IR sensor): Plug the IR receiver sensor into the IR IN on the AC- EX150-BKT transmi9er to pass infrared signals generated from a device or IR Remote. From Remote End: Use an IR-receiver sensor on the AC-EX150-BKT receiver (IR In Port) to send IR signals back to the rack and out of the TRANSMITTER IR Out Port with an emi9er.
Page 12
AC-EX150-BKT *NOTE: For best results, only use the provided IR sensors and emiZers IR Connections to AC-EX150-BKT (Transmitter) ■ IR INPUT (IR SENSOR) IR OUTPUT (IR EMITTER) IR Connections to AC-EX150-BKT (Receiver) ■ IR INPUT IR OUTPUT (RECEIVER SENSOR) (IR EMITTER)
AC-EX150-BKT Troubleshoo9ng Verify Power • Verify ConnecYons - Check that all cables are properly connected • TX Indicator TroubleshooYng Lights • RX Indicator TroubleshooYng Lights • IR Issues - Verify correct connecYons • o Flashing Emi9ers may not funcYon properly. Use the IR emi9ers supplied with the...
AC-EX150-BKT Maintenance To ensure reliable operaYon of this product as well as protecYng the safety of any person using or handling this device while powered, please observe the following instrucYons. Use the power supplies provided. If an alternate supply is required, check voltage, •...
If your product does not work properly because of a defect in materials or workmanship, AVProEdge (referred to as “the warrantor”) will, for the length of the period indicated as below, (Parts/ Labor (10) Years), which starts with the date of original purchase (“Limited Warranty period”), at its opYon either (a) repair your product with new or...
Page 18
AC-EX150-BKT Thank you for choosing AVProEdge! Please contact us with any ques;ons, we are happily at your service! AVPro Edge 2222 E 52nd St N ~ Sioux Falls, SD 57104 1-877-886-5112 ~ 605-274-6055 support@avproedge.com Page 18...
Need help?
Do you have a question about the AC-EX150-BKT and is the answer not in the manual?
Questions and answers