Related Manuals for AVProEdge AC-FRESCO-CAP-4
Summary of Contents for AVProEdge AC-FRESCO-CAP-4
- Page 1 User Manual 1 HDMI Input/4 HDMI Outputs - Dedicated Video Wall Processor Supports up to 18Gbps 4K60 (4:4:4) Output Resolutions Cascade Multiple Processors for Larger Video Wall Arrays AC-FRESCO-CAP-4...
-
Page 2: Table Of Contents
Table of Contents Introduction, Features, In the Box ......................3 Specifications ............................4 Device Overview ............................. 5 Device Overview ............................5 Front Panel .............................. 5 Rear Panel Overview ..........................5 Connection Diagram ..........................6 Initial Setup: Videowall ..........................7 Initial Setup: WebUI ..........................8 WEBUI: I/O Config - Input Settings ...................... -
Page 3: Easy To Use
Introduction The AC-FRESCO-CAP-4 is a Dedicated Video Wall Processor supporting Output Resolutions up to18Gbps 4K60 (4:4:4) through its 1 HDMI Input and 4 HDMI outputs. The FRESCO is a "Plug-and-Play" 4-panel Video Wall which is expandable by cascading multiple FRESCO processors to build larger Video Wall arrays. -
Page 4: Specifications
Specifications Video: Video Resolutions Up to 4k 60HZ 4:4:4 420, 422, 444 (10 AND 12 DEEP COLOR) HDR Formats/Resolutions HDR10, HDR10+, DOLBY VISION, HLG YUV (Component), RGB Color Space (CSC: Rec. 601, Rec. 709, BT2020, DCI, P3 D6500) Chroma Subsampling 4:4:4, 4:2:2, 4:2:0 Supported Deep Color Up to 16 bit (1080), up to 12 BIT (4k) -
Page 5: Device Overview
Device Overview: • Definition - A Video Wall is a special array consisting of multiple computer monitors, video projectors, or television sets tiled together contiguously or overlapped to form one large image/picture. • Video Walls are widely used in commercial and various entertainment venues. Front Panel: •... -
Page 6: Connection Diagram
FRESCO CONNECTION DIAGRAM & OUTPUT-TO-DISPLAY ASSIGNMENTS... -
Page 7: Initial Setup: Videowall
THE FRESCO VIDEO WALL WEB GUI THE BIGGEST CHALLENGE TO SETTING UP A FRESCO VIDEO WALL IS HANGING THE PANELS! Five easy steps to video wall perfection 1. Do a great job hanging the panels 2. Launch the Web GUI using the FRESCO’s IP 3. -
Page 8: Initial Setup: Webui
Initial Setup: WebUI The AC-FRESCO-CAP-4 can be controlled using the Micro USB port, 3pin RS232, or over TCP/IP using the LAN connection. For initial setup it is recommended to connect the videowall processor to a local area network (LAN) and use a computer on the same network in conjunction with the built in WebUI. -
Page 9: Webui: I/O Config - Input Settings
WebUI: I/O Config - Input Settings Input Settings Label - Use this to give an name/alias to your inputs (Apple TV, Cable Box, Roku, etc). Note: There is a 15 character limit to this field, the name will replace the default “IN #” throughout the rest of the WebUI (for instance the Video Videowall processor tab). - Page 10 WebUI: I/O Config - Input Settings Cont. Input Settings EDID - Use these four dropdowns to select your preferred EDID. The available combinations are as follows. 0:Bypass(Follow Output 1) 1:4K60HZ_2CH 2:4K30HZ_2CH 3:1080P_2CH 4:1280x2160 5:1920x2160P60 6:2560x2160 7:3840x720P60 8:3840x1080P60 9:3840x1440 10:USER1 NOTE: If you select USER1 EDID, then drop-downs change to allow you to select from and output to copy from.
-
Page 11: Webui: I/O Config - Output Settings
WebUI: I/O Config - Output Settings Output Settings Label - Use this to give an name/alias to your outputs (Living Room, Den, Kitchen, etc). Note: There is a 15-character limit to this field, the name will replace the default “OUT #” throughout the rest of the WebUI (for instance the Video Videowall processor tab). -
Page 12: Webui: System - Ip Settings
WebUI: System - IP Settings This area contains relevant network information of the AC-FRESCO-CAP-4. Host Name - Devices name on the network. This field is automatically filled with Model Name by default. Model Name - Displays the AVProEdge Model/Part number. -
Page 13: Webui: System - Telnet Settings
WebUI: System - Telnet Settings This area contains relevant Telnet settings for the AC-FRESCO-CAP-4. There are two fields that can changed, Enable Disable switch and the Port Number. • Enable - This switch has two options, Green/Enabled (Default) and Red/Disabled. -
Page 14: Webui: System - User Web Interface
WebUI: System - User Web Interface This switch has two options, Red/Disabled (Default) and Green/Enabled. When enabled (green) there will be three fields that appear, Username, Password, and Confirm Password. NOTE: The Admin Web Interface must first be Enabled and setup before this field will be available to change. -
Page 15: Webui: System - Cloud Services
With the Cloud Services enabled you can use the System tab to check for new Firmware OTA (over the air). This will check the firmware versions currently loaded on the AC-FRESCO-CAP-4 and compare to the latest available. -
Page 16: Webui: System - Firmware Update
4. 45 Seconds Keypad Lock - Enable or Disable (default) the front panel Keypad Lock. MCU/Version - Lists the current Firmware Versions UPDATE FIRMWARE - Check/upload firmware. FACTORY RESET - Restores unit to Factory Defaults REBOOT - Reboots the AC-FRESCO-CAP-4... -
Page 17: Webui: Diagnostics - Hdmi In
WebUI: Diagnostics - HDMI IN Input Settings Label - Use this to give an name/alias to your inputs (Apple TV, Cable Box, Roku, etc). Note: There is a 15-character limit to this field, the name will replace the default “IN #” throughout the rest of the WebUI (for instance the Video Videowall processor tab). - Page 18 WebUI: Diagnostics - HDMI IN Cont. On the left, you will see the current applied EDID information. In the example above, you will see a canned 1080P - No 3D - SDR - 2CH EDID applied to IN 1. Any EDID change, once applied will display here. Signal Info shows the connected source’s current output information.
-
Page 19: Webui: Diagnostics - Hdmi Out
WebUI: Diagnostics - HDMI OUT HDMI Output Label, State, and Connection Reset. Connected Device EDID shows the connected sync’s preferred EDID information and current state. This includes · Manufacturer · Monitor Name · Sink Device Type · Preferred Timing · Supported Audio Formats ·... -
Page 20: Webui: Console
WebUI: Console There is a built in Command Console Using the command API (command list) you can send device specific commands or use as a live monitor while sending commands from a control system (helpful in troubleshooting). Example 1. Click in the white box and type a. -
Page 21: Rs-232 And Tcp/Ip Control
RS-232 and TCP/IP Control: The AC-FRESCO-CAP-4 can be controlled with either RS-232 or TCP/IP commands. Certain switching or format configurations can only be done using these commands. We recommend using either the MyUART (RS-232- free) or Hercules (TCP/IP - free) apps as they are very easy to use for sending commands to the machine. -
Page 22: Command List
Command List: Command Description Help Show Global System Status SET RST Reset to Factory Defaults SET RBT System Reset to Reboot SET ADDR xx Set System Address to xx {xx=00~99} SET INx RST Set Input Port Reset {x=0~1} SET OUTx RST Set Output Port Reset {x=0~4} SET BAUDR x Set System BaudRate to x {x=0~5}... - Page 23 Command List Continued: SET OUTx STREAM ON/OFF SET OUTx STREAM ON/OFF {x=0~4} SET OUTx EXA EN/DIS Set Ex-Audio Output Enable/Disable {x=0~1} GET OUTx VFMT Get Output x Video Timing Format {x=0~4} GET OUTx STREAM Get Output x Stream ON/OFF Status {x=0~4} GET OUTx EXA Get Ex-Audio Output Enable/Disable Status {x=0~1} GET OUTx EDID DATA...
-
Page 24: Troubleshooting
Troubleshooting • Verify Power - The LED on the front of the FRESCO should be lit up RED when power is applied. Check power supply connections to device and power • Verify Connections - Check all cables are properly connected •... -
Page 25: Maintenance, Damage Requiring Service
Maintenance To ensure reliable operation of this product as well as protecting the safety of any person using or handling this device while powered, please observe the following instructions. · Use the power supplies provided. If an alternate supply is required, check voltage, polarity and that it has sulicient power to supply the device it is connected to. -
Page 26: Support, Warranty
Support Should you experience any problems while using this product, first, refer to the Troubleshooting section of this manual before contacting Technical Support. When calling, the following information should be provided: · Product name and model number · Product serial number ·... - Page 27 Dealers, Re-sellers, and Installers can request an RMA AVPro Edge Tech Support Rep or their Sales Engineer. Or you may email support@avproedge.com or fill out the general contact form at www.avproedge.com End users may not request and RMA directly from AVPro Edge and will be referred back to the Dealer, Re-seller or Installer.
- Page 28 LEGAL STUFF. Limitation on Liability The maximum liability of AVPro Global Holdings LLC under this limited warranty shall not exceed the actual purchase price paid for the product. AVPro Global Holdings LLC is not responsible for direct, special, incidental or consequential damages resulting from any breach of warranty or condition, or under any other legal theory to the maximum extent permitted by law.
- Page 29 Thank you for choosing AVProEdge! Please contact us with any questions, we are happily, at your service!
Need help?
Do you have a question about the AC-FRESCO-CAP-4 and is the answer not in the manual?
Questions and answers