TABLE OF CONTENTS TOPICS PAGE 1-INTRODUCTION 2-TECHNICAL DATA 3-WARNING SIGNS AND SAFETY DETAILS 4-TRANSPORTING AND MOVING 5-OPERATION OF THE MACHINE 6-CLEAN-UP AND MAINTENANCE 7-ELECTRICAL CIRCUIT DIAGRAM 8-TROUBLESHOOTING...
1-INTRODUCTION Dear User, Thank you for purchasing our device and for your reliance upon our company. Our devices have been used within our customers kitchen, your kitchen in 100 countries. Our devices are produced in compliance with international standards. Important notice: Please read or ensure that the users read this user’s manual in order to achieve the desired performance in line with your expectations and to use your device for long years.
WARNING SIGNS AND SAFETY DETAILS 3.1 Warning Signs Power Network Attention Important Grounding Electricity Grounging The machine should never be exposed to direct sunlight. The machine should never be left in water and its outer surface should never be cleaned with high pressure water.
TRANSPORTING AND MOVING The machine should be placed vertically on a palette by manpower. Transportation should be carried out by inserting the forklift forks under the machine. If the transported distance is far, the machine should be moved slowly and fixed to the palette or supported by another personnel to prevent jolt, if necessary.
Page 10
4.3 Electrical Connections: All electrical connections must be made by authorized service personnel in accordance with local and national standards and directives. All products must be connected to the residual current device of 30mA. Use the power socket and an appropriate connector to connect the appliance. Power socket is on the side. This connection is additional to existing grounding.
Page 11
4.6.2. Models With a Drain Pump: If drain vent is below the appliance’s drain outlet, attach the hose to the drain vent with a downward slope. Otherwise, drain vent height should be 60 cm max. The Ø28 mm (3/4ʺ) drain vent should not be below the appliance base.
Page 12
Water temperatures can be adjusted. During production, our appliance is set to the following temperature values. The temperature should not be set higher than these temperatures. OBM 1080D / OBM 1080D P / OBM 1080D R/ OBM 1080D RT / OBM 1080D PD / Models:...
5- OPERATION OF THE MACHINE 5.1 Getting to know our device: To understand the information in the user manual correctly, the main parts of the machine should be known, please have the information by examining the picture below. HANDLE RACK HOUSING RACK WASHING/RINSING ARMS FILTER...
Page 14
5.2 Operation: 5.3 Description of the Appliance Unlike domestic appliances, industrial dish and glass washers are designed for almost uninterrupted operation. 5.4 Control Panel Before starting the appliance, first get familiar with the control buttons and signal items on the front panel. In addition, get familiar with the location of power and water cut-off switches.
Page 15
5.7. Starting a Wash Cycle 5.7.1 Starting a Wash Cycle Models; OBM 1080D / OBM 1080D P / OBM 1080D R / OBM 1080D RT / OBM 1080D PD/ OBM 1080D PDT / OBM 1080D PDR / OBM 1080D PDRT) Open the door, load the first basket and check that upper and lower arms turn freely.
Page 16
(Factory Settings) finished,the drain pump will stop automatically. After finish the drain process press the’On/Off’ switch for the turn off the machine. Note: Once draining is complete, it is recommended to disconnect mains water and electrical supply, and clean the appliance as described.
Page 17
5.10. Recycling: If you intend to recycle or dispose of the appliance, make sure that local and national regulations are observed. NOTE: 1- Hardness of water supplied to the appliance should be softened to 0-10 °fH. 2- Extremely hard water both shortens the service life of the appliance and drops its washing performance. Calcified parts are outside the warranty coverage.
6- CLEAN-UP AND MAINTENANCE 6.1 Periodical Maintenance and Clean-up Daily maintenance should be carried out by people informed about the safety instructions as following, after disconnecting power supply and water connections. 6.1.1 Daily Maintenance: Daily maintenance should be carried by the user. In order to clean up the machine within the day following should be carried out periodically after the washing operation: 1.
8- TROUBLESHOOTING Please check the following items before calling the call centre: 1. Equipment does not run partially or completely, check the electrical supply to the appliance. 2. Check mains water and electrical connection is in place and active. 3. Electrical supply to the appliance should be 400 V 3NPE~/50 Hz. 4.
Page 21
10. Appliance does not drain; Check and clean the filters. Check if drain hose and drain vent are not clogged. In appliances with a motorized drain unit, drain system should comply with section 4.6. 11. Water intake is slow; ...
Need help?
Do you have a question about the OBM 1080D and is the answer not in the manual?
Questions and answers