Download
Share
Print this page
  1. Manuals
  2. Brands
  3. BUFFALO TURBINE Manuals
  4. Blower
  5. BLITZ BT-SB40
  6. Operator's manual

BUFFALO TURBINE BLITZ BT-SB40 Operator's Manual

Stand-on debris blower
Hide thumbs

Advertisement

Quick Links

Download this manual
BLITZ BT-SB40
Stand-On Debris Blower
Operator's Manual
Revision A
September 2024

Advertisement

loading
Need help?

Need help?

Do you have a question about the BLITZ BT-SB40 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BUFFALO TURBINE BLITZ BT-SB40

Summary of Contents for BUFFALO TURBINE BLITZ BT-SB40

  • Page 1 BLITZ BT-SB40 Stand-On Debris Blower Operator’s Manual Revision A September 2024...
  • Page 2 Checking Tire Pressure ..........27 Slope Guide ..............9 Checking Engine Oil Level ..........27 Warranty: Checking/Adding Transaxles’ Oil ........28 Buffalo Turbine Warranty Policy ........10 Maintenance Procedures: Warranty Registration Form ......... 11 Greasing the Machine ........... 29 Controls and Adjustment: Changing the Engine Oil and Filter .......
  • Page 3 Operator’s Manual. This manual pertains to the BLITZ BT-SB40 Stand-On Debris Blower. Keep this manual accessible for regular reference and transfer it to any subsequent operators or owners. Should you require assistance or additional information, contact your Buffalo Turbine dealer or distributor.
  • Page 4 Safety and Training As the owner, YOU are responsible for the safe operation and maintenance of your Buffalo Turbine Debris Blower. Ensure that everyone who operates, maintains, or works around this equipment is fully familiar with the procedures and safety information provided in this manual. This guide will help you...
  • Page 5 Check for Debris Accumulation: Ensure that no leaves, grass, or debris have accumulated on or near the engine or exhaust system, as this could pose a fire hazard. Following these steps will help minimize risks and ensure the Buffalo Turbine Debris Blower is prepared for safe operation.
  • Page 6  Always inspect the blower, bolts, and connections to the blower for wear or damage.  Never run the engine in an enclosed area to avoid carbon monoxide buildup.  Operate only in well-lit areas, steering clear of holes and hidden hazards. ...
  • Page 7 No Riders Allowed  Never allow passengers on the machine. Extra riders can fall, interfere with safe operation, or cause a loss of control. Parking 1. Stop the machine on level ground and ensure the motion control arms return to the neutral position.
  • Page 8 opening or disassembling any component that contains fluids. In the event of a spill, immediately contain the spill using absorbent materials, and clean the area thoroughly to prevent slipping hazards or damage to the machine. Never pour waste fluids onto the ground, down a drain, or into any source of water, as improper disposal can harm the environment.
  • Page 9  Ensure the machine is on a firm, level surface and securely blocked to prevent it from tipping or sinking into soft ground.  Cover the machine with a weatherproof cover and secure it tightly to protect it from the elements.
  • Page 10 Stickers Safety stickers and icons on the machine show essential warnings and instructions. Operators must know their locations and meanings, as these symbols highlight hazards and safe operating practices. Regularly check that decals are intact and legible. WARNING Replace any that are missing or damaged to ensure continued safety. Sticker Identification ...
  • Page 11 Slope Guide Use this guide to measure and confirm the slope for safe operation. 1. Fold the guide along the line that matches the recommended slope from your machine’s manual. 2. Hold the guide at arm’s length and align its right edge with a vertical surface, such as a tree or building. 3.
  • Page 12 DEBRIS BLOWER. This warranty shall not apply to any DEBRIS BLOWER, which has been altered outside the factory in any way so as, in the judgment of Buffalo Turbine, to affect its operation or reliability, or which has been subject to misuse, neglect, or accident.
  • Page 13 WARRANTY REGISTRATION FORM & INSPECTION REPORT Any units not registered with Buffalo Turbine are not eligible for warranty claims This form must be filled out by the dealer and signed by both the dealer and the customer at the time of delivery...
  • Page 14 Control Functions and Location Motion Control: [Left Wheel A, Right Wheel B] Fuel Tank Selector Switch [G]   Push both arms forward to drive forward Flip switch forward to select right tank   Pull both arms backwards to drive backwards Flip switch backward to select left tank ...
  • Page 15 Adjusting the Operator’s Platform The operator platform can be adjusted for ride quality using the holes labeled 1 through 5. Hole 1 provides the softest ride, and hole 5 provides the stiffest ride. To adjust the ride quality: 1. Remove the retaining clip and pin from the current hole. 2.
  • Page 16 Adjusting the Stationary Arm Adjusting the Stationary Arm: The stationary arm can be adjusted to limit the machine's speed or maintain a constant speed when using the blower. This adjustment is useful for training new operators, as it allows for speed restriction to enhance control and safety.
  • Page 17 Removing the Leaning Pad The leaning pad on the machine serves as a protective cover and ergonomic support for the operator, enhancing comfort during use. Removing the leaning pad provides necessary access to many of the machine’s internal components, facilitating maintenance and adjustments. Leaning Pad Removal: Rotate the latch until it allows for leaning pad removal [1].
  • Page 18 Adjusting/Testing the Parking Brake The parking brake secures the machine when stationary, preventing unintended movement. Regular testing is recommended to ensure it functions properly and maintains the safety of the machine during operation. Directions: 1. Position the machine on a level surface. 2.
  • Page 19 Adjusting the Position of the Motion Control Arms The control arms can be adjusted to correct slack or limited travel. Make adjustments if the control arms contact the stationary arm when pushed forward or if they are more than 1/4” away from it when the stationary arm is in its farthest position.
  • Page 20 Machine Specifications Engine Specifications Model: 40HP EFI/ETC Engine Type: 4-Stroke, EFI Displacement: 993 cc (60.60 ci) Cooling System: Air-cooled Oil Capacity: 78 - 80 oz (2.3 - 2.4 L) Fuel Type: Gasoline Fuel Filter: Replaceable Element Type Spark Plug Gap: 0.030 in (0.76 mm) Battery: 12 Volt, 340 CCA...
  • Page 21 Maintenance Schedule Initial Maintenance Schedule for BT-SB40 □ Once at 10 Hours Completed: ● Check transaxles’ oil level. ● Check parking brake operation. ● Check wheel lug nut torque. ● Check air pressure in tires. ● Check transaxles’ drive belt. □...
  • Page 22 Maintenance Log Date: Hours on Machine: Maintenance Performed: Notes:...
  • Page 23 Engine Maintenance Consult the maintenance schedule and machine operator's manual for detailed engine maintenance schedules and procedures. Transaxle Maintenance Consult the maintenance schedule and machine operator's manual for detailed transaxle maintenance schedules and procedures. Battery Maintenance Keep open flames and sparks away from the battery. When handling the WARNING battery, take care to avoid spilling battery acid, and always disconnect the negative cable first and reconnect it last to prevent short circuits.
  • Page 24 Lifting and Hoisting the Machine Jack and Support Points: This diagram illustrates the designated jack points and support points for the BT-SB40 to ensure proper lifting and stabilization during maintenance. Legend Jack Points Support Points...
  • Page 25 Hoist Pick-Up Points: This diagram illustrates the designated hoisting points for the BT-SB40 to ensure proper lifting during maintenance.
  • Page 26 Engine Component Identification Engine Oil Dip Stick: [A] Drain Hose: [D] Oil Fill Cap: [B] Oil Filter (Opposite Side of Engine): [E] Drain Valve: [C] Transaxle Component Identification Transaxle(s): [A] Oil Reservoir Cap: [C] Transaxle Oil Reservoir: [B] Reservoir “FULL COLD” Fill Line: [D]...
  • Page 27 Fuse Box Location & In-Line Fuse Identification Note: The following image shows the components located above the (+) terminal on the battery. Fuse Box Main Harness Fuse (30A): [A] Fuel Reserve Fuse (10A): [B] Fuse Box Component Identification Ignition Relay: [C] Headlights Fuse (10A): [E] Contactor/Relay Fuse (10A): [D] USB Auxiliary Port Fuse (5A): [F]...
  • Page 28 Checking/Adding Fuel WARNING Gasoline is highly flammable and should be handled with caution.  Allow the engine to cool for at least 3 minutes before refilling.  Do not permit open flames, smoking, or matches in the vicinity.  Avoid overfilling and clean up any spills immediately. ...
  • Page 29 Checking Tire Pressure WARNING Explosive Tire and Rim Separation Hazard Improper handling of tire and rim assemblies can result in serious injury or death. Tire pressures should be checked regularly and maintained according to the levels specified in the Specifications chart. These recommended pressures may differ slightly from the "Max Inflation" value stamped on the tire sidewall.
  • Page 30 Checking/Adding Transaxles’ Oil Before you check or add oil:  Ensure the machine is on a level surface.  Clean the area around the transaxles’ oil reservoirs to remove any dust, dirt, or debris.  Make sure the machine is cold before proceeding. Directions: 1.
  • Page 31 Greasing the Machine Grease Change Interval: Every 25 hours. Tools and Supplies:    Grease Gun Grease Rags Directions: 1. Grease the fittings shown on the machine, using a grease gun, until new grease appears beneath the large washer above the fitting. 2.
  • Page 32 Changing the Engine Oil and Filter Engine Oil and Oil Filter Change Interval: Every 100 hours or annually, whichever comes first. Note: It is recommended to run the engine until the oil is warmed, as this helps to thin the oil, allowing it to drain more effectively.
  • Page 33 Changing the Air Filter Air Filter Change Interval: Every 400 hours or annually, whichever comes first. Directions: 1. Apply the parking brake and remove the key from the ignition. 2. Undo the fasteners on the front and rear of the air cleaner [Figure 1]. Figure 1 Air Cleaner Clamp 3.
  • Page 34 Changing the Fuel Filter Fuel Filter Change Interval: Every 400 hours or annually, whichever comes first. Note: If this is being performed as scheduled maintenance and the fuel filter is operational, it is recommended to run a fuel tank until the engine stalls from lack of fuel. At that point continue to the Fuel Filter Removal &...
  • Page 35 Changing the Transaxles’ Oil and Filters Oil & Filter Change Interval: Perform an initial oil and filter change at 75-100 hours, followed by changes every 400 hours thereafter. Tools and Supplies:   Optional 11/16” Wrench 3/8” Socket   ...
  • Page 36 11. Remove the old filters [Figure 7] using filter wrench as shown if required. Figure 7 Oil Filter Removal 12. Remove the plugs from the location shown [Figure 8] using a 1/4” Hex Bit Socket and ratchet. *Do Not Discard* Note: This should help the transaxles drain completely. Figure 8 Plug Locations on Transaxle 13.
  • Page 37 Air Purging the Transaxles Due to the effects air has on efficiency in hydrostatic drive applications, it is critical to purge it from the system. Air creates inefficiency because its compression and expansion rate is higher than that of the oil approved for use in hydrostatic drive systems.
  • Page 38 Disconnecting and Connecting the Battery Tool & Supplies List:   1/2” Socket Extension of 6” or more   Socket-Driving Wrench Torque Wrench (15 ft-lbs) Battery Disconnect Engage the parking brake and remove the key from the ignition. Remove the leaning pad from the machine and set it aside.
  • Page 39 Removing and Installing the Battery Tool & Supplies List:   1/2” Socket Extension of 6” or more   Socket-Driving Wrench Torque Wrench (15 ft-lbs) Battery Removal Chock the wheels. Disengage the parking brake and remove the key from the ignition. Remove the leaning pad from the machine and set it aside.
  • Page 40 Battery Install Note: Skip this step if reinstalling the same battery that was previously removed. Compare the new battery to the one that was removed to make sure they are the same physical size, and share the same performance rating [Machine Specifications]. Reinstallation is the reverse of removal.
  • Page 41 Changing the Drive Belt Tools and Supplies:   Jack or Hoist 9/16” Socket   Jack Stands Rated for 1,000+ lbs. (2) 9/16” Wrenches   1/2” Drive Breaker Bar Torque Wrench (90 ft-lbs.)   1/2” Drive Ratcheting Wrench Marker ...
  • Page 42 15. With the tensioner arm securely restrained, the belt should be relieved of all tension. Reach an arm through the access panel and confirm that the belt is slack. 16. If still intact, take a look at the belt and note how it is routed prior to removal. 17.
  • Page 43 Removing and Installing the Guard Tools and Supplies:    7/16” Wrench Marker 7/16” Socket   Torque Wrench (8 ft-lbs) Ratchet Removal: 1. Remove the hardware from the top of the guard using a 7/16” socket, ratchet, and 7/16” wrench.
  • Page 44 Cleaning with Pressurized Air and Water WARNING Wear protective clothing, shoes, and eye protection (goggles or face shield) to prevent injury from debris or hot water. Note: During cleaning, cover all electrical components to shield them from water exposure, and avoid spraying water directly onto these components or sensitive engine parts to prevent water damage.
  • Page 45 Parts References...
  • Page 55 Bill of Materials PART # DESCRIPTION QUANTITY REFERENCE PGS. 1100 1-1/4" 3/8-24 Hex Bolt 43, 48 1101 1-1/2" 3/8-24 Hex Bolt 1102 1-3/4" 3/8-24 Hex Bolt 1104 2" 3/8-24 Hex Bolt 1105 3/8-24 Hex Nut 1107 3/8 Lock Washer 43, 48 1108 3/8 Flat Washer 1109...
  • Page 56 2305 2-1/4" 3/8-24 Hex Bolt 2639 5/8" Bore Rubber Grommet 2869 3/8" X 7/16-20 Set Screw 3007 Constant Tension Hose Clamp 3062 EPA Emissions Label 3067 EPA Emissions Date Label 3238 1" Wide Battery Strap 3314 Fuel Tank Cap 3398 Rotation Motor 3837 Elbow Base Ring Bearing...
  • Page 57 4810 1/4-20 Serr. Flange Hex Nut 46, 50 4811 Handle Bar Grip; Vinyl Black 4812 Fixed Handlebar Weldment 4816 Motion Control Weldment 4820 Push-Button Switch For Nozzle Rotation 4821 Motion Control Link 4822 Transaxle Extension Arm 4823 Leaning Pad Support Weldment 4827 Leaning Pad 4829...
  • Page 58 4908 Bottom Guard 4911 Fuel Tank Strap 4912 3/8" Washer 4913 9/16 OD Bronze Bushing 4914 9/16" Delrin Washer 4917 1" 5/16-18 Serr. Flange Hex Bolt 4918 Parking Brake Safety Switch 4919 Lower Parking Brake Spring 4920 Upper Parking Brake Spring 4921 Rocker Switch (4 Terminal) 4922...
  • Page 59 5057 1/4" X 1/4" 3/16 Barbed Plastic Tee 5060 5/16" Dia Clevis Pin, 3/4" Usable Length 5062 O-Ring For Transaxle Adapter 5063 19" X 5.5" "Buffalo Turbine" Decal 5064 AX52 V-Belt 5073 Wheel/Yoke Spacer 5074 Wheel Bearing Spacer 5075 Transaxle Sub Assembly...
  • Page 60 Troubleshooting Guide Symptom Causes Actions Out of fuel Add fuel to fuel tanks. Gas is old or stale. Replace fuel in fuel tanks. Water in fuel. Replace blown fuse. See Fuse Location & Blown fuse Identification. Clean and tighten battery terminals. See Loose or corroded battery connections Battery Maintenance.
  • Page 61 Adjust tire pressure. See Machine Incorrect tire pressure. Specifications. Check blower for damage, cracks, broken Blower is out of balance. or bent blades. Contact Buffalo Turbine Excessive Machine Service Department. Vibration Excessive dirt or debris on rotating Free rotation components of dirt or components.
  • Page 62 Notes __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________ __________________________________________________________________________________________________...