Page 1
Operation and Maintenance Manual VLP-Series Hydraulic Bench Press Document Number: L4498 Document Revision: A Issue Date: August, 2021 Language: English EN Hand Pump Air Pump To reduce the risk of injury, user must read and understand this document before use.
Page 2
For additional information, visit www.enerpac.com. WARRANTY Refer to the Enerpac Global Warranty document for terms and conditions of the product warranty. Such warranty information can be found at www.enerpac.com. NAMEPLATE Refer to the nameplate decal for the press model number. Decal appearance and text may vary depending on location of product manufacture.
Page 4
Failure to observe and comply with the following tags, or decals. In the event that any questions or precautions could result in death or serious personal concerns arise, contact Enerpac or a local Enerpac injury. Property damage could also occur. distributor for clarification.
Page 5
• Always use Enerpac pumps and hoses. • Be sure your workplace is safe. Follow the • Always use Enerpac replacement parts. instructions your workplace’s...
Page 6
3. Features & Components Key: Hydraulic Cylinder Hydraulic Hose Hydraulic Pressure Gauge Gauge Adapter 5A. Hydraulic Pump, Hand Operated (Models VLP106P142 and VLP106P142U only) 5B. Hydraulic Pump, Air Operated (Models VLP106PAT1 and VLP106PAT1U only) Frame Figure 1: Features and Components L4498_a...
Page 7
[mm] per second with pump running and 100 psi [69 bar] and 12 scfm [339 l/min] present at air inlet. Approximate weight of press frame, pump, hoses, fittings and cylinder. 4.2 Specifications - Hydraulic System Max. Hydraulic Hydraulic Pump Hydraulic Cylinder Operating Pressure Press Model Stroke Number Enerpac Pump Valve Enerpac Cylinder Model No. Type Type Model No. Type...
Page 8
After unpacking the pump, be certain that the hydraulic horizontal position. It can be floor mounted or installed reservoir is filled to the proper level with Enerpac oil. Refer on a workbench or other suitable work surface. to the separate instruction manual provided with the pump Mount the frame with four bolts of appropriate size (user for complete pump setup and operation instructions.
Page 9
6. Operation Apply PTFE Tape Hyd. Pressure WARNING Before operation, be certain to read and Gauge understand all safety precautions contained in Section 1 of this manual. Also read and understand all safety precautions contained in the separate manuals included with the hydraulic pump and cylinder. Failure to observe Hyd.
Page 10
(0) psi/bar when pressure is fully relieved. 7. V-Blocks Lever OPEN CLOSE Enerpac V-Blocks (model VB-10) are available as an optional accessory. They can be used to facilitate the positioning of pipes and bars. See Figure 10. V-Blocks Release Valve Figure 8: Hand Pump Features (typical) 6.3 Using Air Operated Pump...
Page 11
9. Troubleshooting The information in the Troubleshooting Guide is intended as an aid to help diagnose and correct various possible problems that may occur. For repair service, contact your nearest Enerpac Authorized Service Center. Troubleshooting Guide Problem Possible Cause Action 1.
Page 12
10. Parts List 10.1 Exploded View, VLP-Series Hydraulic Bench Press Notes: • Threaded NPT and NPTF connections: Apply PTFE tape to male threads and tighten each item to 1.5 to 3 turns past finger tight (minimum of 40 ft-lbs [54.2 Nm] ). •...
Page 13
Decal, Enerpac - - - Enerpac V-Block Kit VB-10 VB-10 VB-10 VB-10 Indicates items included and available only as part of Label Kit, VLP10LS. Optional accessory (See Figure 10). Two V-blocks are included in each kit. Order as required.
Need help?
Do you have a question about the VLP Series and is the answer not in the manual?
Questions and answers