Advertisement
Quick Links
Translated from German to English - www.onlinedoctranslator.com
D
original operating instructions
PTO disc wheel shredder RAMBO-HC20HZ
Model: _____________
Both the model number and the serial number can be found on the rating plate on the
machine. You should keep both numbers in a safe place for future reference. This
manual explains the basic functions and uses of the machine.
DANGER!The machine is delivered without hydraulic oil.
RAMBO-HC20HZ
Serial number: ______________________________
Art. No.: RAMBOHC20HZ
www.lumag-maschinen.de
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Lumag RAMBO-HC20HZ
Summary of Contents for Lumag RAMBO-HC20HZ
- Page 1 RAMBO-HC20HZ Art. No.: RAMBOHC20HZ www.lumag-maschinen.de original operating instructions PTO disc wheel shredder RAMBO-HC20HZ Model: _____________ Serial number: ______________________________ Both the model number and the serial number can be found on the rating plate on the machine. You should keep both numbers in a safe place for future reference. This manual explains the basic functions and uses of the machine.
- Page 2 CONTENT / GENERAL GENERAL CONTENTS 1. GENERAL 2. INFORMATION ON THE OPERATING INSTRUCTIONS 3 3. INTENDED USE 4. SCOPE OF DELIVERY 5. TECHNICAL DESCRIPTION 6. SPECIFICATIONS DANGER! 7. OPERATING HOURS RESTRICTION Read safety instructions 8. ENVIRONMENT instructions. 9. SYMBOLS 10. SAFETY INSTRUCTIONS Use this manual to familiarize yourself with the GENERAL SAFETY REGULATIONS SPECIFIC SAFETY REGULATIONS...
- Page 3 INFORMATION ON THE OPERATING INSTRUCTIONS / INTENDED USE name machine The term “machine” is the commercial name of the replaced item to which this operating manual - see cover page - refers. Before starting any work on or with the machine, read the operating instructions, especially the Safety chapter and the relevant safety instructions.
- Page 4 SCOPE OF DELIVERY / TECHNICAL DESCRIPTION SPECIFICATIONS / OPERATING TIME LIMITATIONS SPECIFICATIONS SCOPE OF DELIVERY After unpacking, check the contents of the Model RAMBO-HC20HZ transport box for drive ► Completeness power requirements ► possible transport damage tractor approx. 20 hp PTO speed max.
- Page 5 ENVIRONMENT / SYMBOLS SYMBOLS WARNING! Keep hands and feet away from rotating blades. Symbols are attached to the machine. These Do not touch any openings, the feed represent important information about the product hopper or the discharge chute when the or instructions for use.
- Page 6 SYMBOLS / SAFETY INSTRUCTIONS Make sure you read and understand all the instructions and safety warnings in the manual. Do 10. SAFETY INSTRUCTIONS not attempt to operate the machine until you are familiar with the machine and know how to operate GENERAL SAFETY REGULATIONS and maintain it properly.
- Page 7 SAFETY INSTRUCTIONS part can cause injury. Stay alert and watch what you Always wear good eye and hearing protection when are doing. Use common sense when operating the operating the machine. machine. Always ensure that the surface is stable and level and that you have a secure footing.
- Page 8 SAFETY INSTRUCTIONS Always use original accessories. The use of other Check regularly and replace if necessary. Damaged tools and accessories can lead to unforeseeable cutting tools (cracked, knocked out or otherwise damage to the machine or pose a risk of injury to damaged) must be replaced immediately.
- Page 9 SAFETY INSTRUCTIONS → Feed the material to be chopped slowly and Never operate the machine without the protective carefully into the feed hopper.ATTENTION, device installed and intact. automatic feed!Never use your hands! → Always insert branches with the thick end first. Carrying persons on the machine is not permitted.
- Page 10 SAFETY INSTRUCTIONS 11. CONTROLS Adjustable discharge flap Rotatable discharge chute PTO unit (not visible on picture) three-point hitch stand tank cap / hydraulic oil tank hydraulic oil tank disc wheel housing foldable feed hopper forward- reverse feed roller speed feed roller (not visible in picture) Hydraulic oil temperature indicator (not visible in picture)
- Page 11 SAFETY INSTRUCTIONS 13. ASSEMBLY Foldable feed hopper (9) The feed hopper can be folded up for transport or The machine consists of parts that weigh more than to clean the feed roller and remove blockages. 20 kg. These parts must always be carried by at least two people.
- Page 12 FUNCTIONS / ASSEMBLY Now finally tighten the two lock nuts (M10) of the adjustment rod for the forward and reverse feed roller. (see pictures). Mount the feed roller (10) Mount the feed roller forward/reverse lever to the DANGER! feed roller using the screws and nuts already in the Before use, check that the feed roller funnel.
- Page 13 ASSEMBLY 14. BEFORE FIRST USE 16. COMMISSIONING PREPARATION FOR USE A NOTICE ■ Make sure that the machine is completely and The device is not supplied with hydraulic oil. Fill the correctly assembled. machine as described under "FUELLING". ■ Only use the machine on a level and solid surface.Attention, risk of tipping over! ■...
- Page 14 BEFORE FIRST USE / REFUELLING ■ Before starting, check that there are no chopped A NOTICE residues in the hopper. Severely damaged or bent blades must be replaced ■ Chopping may only take place once the required with new blades. PTO speed has been reached.
- Page 15 FUEL 18th MAINTENANCE hands always before Keep away from ejection openings! Improper maintenance or failure to take care of up to Ø 200 mm, branches, bushes or branches or correct a problem can create a hazard during Green waste can be chopped. operation.
- Page 16 FUEL / COMMISSIONING Never use a high-pressure cleaner to After lubricating the grease nipples, close clean the machine. Water can the safety covers properly again. penetrate into narrow slots and damage spindles, pulleys and bearings. Using a high-pressure cleaner will result in a shortened FASTENING SCREWS service life and operational capability.
- Page 17 COMMISSIONING The counter knife can be used on one side. 3. Loosen the three M10 hex bolts (Fig. 3) that secure the counter knife to the lower disc wheel The fastening screws of the blades must be housing to allow it to slide in and out freely. This tightened with 60Nm and medium screw locking movement increases or decreases the gap between compound if you change them.
- Page 18 TANKIE N N E U BNG AHME S T/AI NB H TARLIT V-BELT The four V-beltsbefore each commissioningcheck their condition. When changing a V-belt, all four V-belts must always be replaced. 1. Remove the V-belt cover/PTO cover. To do this, remove the split pin above it. 2.
- Page 19 COMMISSIONING 19. TRANSPORT NSRT Before transporting or moving the device or storing it indoors: ■ Transport the machine in an upright position to avoid oil leakage. ■ When transporting the machine on a vehicle, tie it down properly. A NOTICE Only transport the machine upright! A NOTICE The machine is not approved for use on public roads.
- Page 20 Warranty work is carried out exclusively by our LUMAG service workshop. Defects that occur The warranty is excluded with regard to parts if within the warranty period due to material or...
- Page 21 Telephone: +49 / (0)8571 / 92 556-0 Fax: +49 / (0)8571 / 92 556-19 that the product Designation: PTO disc wheel shredder Type designation: RAMBO-HC20HZ meets the essential protection requirements of the above-mentioned EC directives. Conformity is based on the following standards: EN ISO 12100:2010...
- Page 22 COMPONENTS OF THE MACHINE / Complete view (1/8)
- Page 23 COMPONENTS OF THE MACHINE / Main frame (2/8)
- Page 24 MACHINE COMPONENTS / Flywheel Housing 1 (3/8)
- Page 25 MACHINE COMPONENTS / Flywheel housing 2 (4/8)
- Page 26 COMPONENTS OF THE MACHINE / Flywheel (5/8)
- Page 27 COMPONENTS OF THE MACHINE / Feed hopper (6/8)
- Page 28 COMPONENTS OF THE MACHINE / Discharge hopper (7/8)
- Page 29 MACHINE COMPONENTS / Hydraulic hoses (8/8)
- Page 30 LUMAG GmbH Rudolf-Diesel-Straße 1a D-84375 Kirchdorf am Inn Telephone: +49 (0)85 71 / 92 556 - 0 Fax: +49 (0)85 71 / 92 556 - 19 www.lumag-maschinen.de Status: 09/2022 - RAMBOHC20HZ...
Need help?
Do you have a question about the RAMBO-HC20HZ and is the answer not in the manual?
Questions and answers