Lumag RAMBO-HC15PRO Original Operation Manual

Lumag RAMBO-HC15PRO Original Operation Manual

Gasoline shredder

Advertisement

GASOLINE SHREDDER
Original Operation Manual
RAMBO-HC15PRO
ATTENTION! The machine is delivered without engine oil and fuel.
Both the model number and serial number can be found on the nameplate on the machine. You should keep
both numbers safe so that you can refer to them in the future. This manual explains the functions and
applications of the machine.
FOR YOUR SAFETY
Read the user manual before commissioning,
safety and warning instructions must be observed!

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RAMBO-HC15PRO and is the answer not in the manual?

Questions and answers

Summary of Contents for Lumag RAMBO-HC15PRO

  • Page 1 GASOLINE SHREDDER Original Operation Manual RAMBO-HC15PRO ATTENTION! The machine is delivered without engine oil and fuel. Both the model number and serial number can be found on the nameplate on the machine. You should keep both numbers safe so that you can refer to them in the future. This manual explains the functions and applications of the machine.
  • Page 2 21. Warranty / Guarantee / Customer 13.1 Gasoline engine Service 13.2 Refuelling 22. EC Declaration of Conformity 13.2.1 Filling up engine oil 13.2.2 Fuelling 23. Components RAMBO-HC15PRO 14. Commissioning 14.1 Preparation for the site of operation 14.2 Start process 14.3 Switching off the engine 14.4 Stopping the engine in an emergency 13.5...
  • Page 3: Important Notice

    Information on the user manual contents to third parties are not permitted, as far as not expressly agreed. This user manual provides important instructions on the use of the RAMBO-HC15PRO gasoline shredder. A prerequisite for safe working is the correct observance...
  • Page 4: Intended Use

    Intended use Operating hours restriction The gasoline shredder - RAMBO-HC15PRO - is designed exclusively for shredding bushes, shrubs, In residential and small residential estates or on barks, branches up to a thickness of 15 cm. The the grounds of hospitals and nursing homes, machine is not suitable for preparing garden soil.
  • Page 5 Safety instructions Safety This section provides a comprehensive overview of WARNING! all important safety aspects, for adequate protection of the operator, as well as for safe and Familiarise yourself with the machine. Proper trouble-free operation. training is a prerequisite for safe operation of this machine.
  • Page 6 Carry out all work calmly and prudently. Operating personnel Never leave the machine running unattended. When starting the engine, do not stand in the area WARNING! of the ejection openings. Persons who are not familiar with the user manual, children, young people under the age of Do not start shredding until the gasoline engine 18 as well as persons under the influence of has reached maximum speed.
  • Page 7 If there are any blockages on the cutting unit and any risk to the operator. The following protective ejector, switch off the engine, remove the spark measures must be observed: plug and clean the cutting unit with a suitable tool. –...
  • Page 8 Transport and store fuel and oil only in approved out by qualified electricians. and marked canisters. Use only original – LUMAG – spare parts and Do not transport or store fuel and oil near accessories. The use of other spare parts and combustible or highly flammable materials as well accessories may increase the risk of accidents.
  • Page 9 Residual dangers and protective Electrical residual dangers Direct or indirect electrical contact measures Touching live parts when electrical or defective components are open or electrical connection cables which are not properly connected can lead to injuries. WARNING! → Never touch the spark plug connector or the spark plug when the engine is running.
  • Page 10: Mandatory Signs

    → Watch out for obstacles in the working area. Warning and information Always make sure you have a secure footing and symbols used wear safety shoes. 5.10 Behaviour in an emergency In the event of an accident, initiate the appropriate first aid measures and request qualified medical There are symbols on the machine that represent assistance as soon as possible.
  • Page 11 Shredding of branches of all kinds Wear safety shoes with steel caps. up to max. 150 mm diameter, depending on the type of wood and freshness. Wear protective gloves. Electric start, ignition key (12 V) Wear eye protection. Wear hearing protection. Nameplate Equipped with...
  • Page 12: Machine Overview

    Machine overview Gasoline engine Shredder Engine switch (main switch) = Ignition switch on E-start Starter grip Recoil starter Choke valve 1 Adjustable deflector Fuel switch 2 Ejection chute Air filter 3 Gasoline engine Muffler 4 Drawbar Throttle lever 5 Trailer coupling Spark plug, spark plug connector 6 Steering axle with 2 wheels 7 Blade chassis...
  • Page 13 Oil drain bolt (11) Functions The oil drain bolt is located at the rear of the engine. Engine Fuel tank (12) There is a fuel switch under the tank. Engine switch (main switch) = Ignition switch on E-start (1) Centrifugal clutch The engine switch in the OFF position prevents the The engine has a centrifugal clutch coupled to the machine (engine) from starting.
  • Page 14: Technical Data

    Drawbar (4) Technical data A drawbar is provided for better guidance of the machine. Model number RAMBO-HC15PRO Drive 4-stroke OHV Gasoline engine Displacement 420 cm³ IMPORTANT NOTICE! Engine power, max. 9.0 kW Motor speed max. 3,600 1/min Dismantle the drawbar when loading!
  • Page 15: Technical Description

    Connect battery: Technical description 1. Turn ignition key on E-start (1) to OFF position and remove. 2. First connect the red wire to the positive The shredder is used for shredding woody terminal (+). material, preferably in the garden area. 3.
  • Page 16: Standard Equipment

    If you have any questions or problems with the machine, please contact us. You can reach us by email: info@lumag-maschinen.de or by telephone at +49 8571/92 556-0. Standard equipment A Basic unit with gasoline engine and rotor B Infeed chute...
  • Page 17: Drive Type

    Check engine oil level Drive type Switch off the engine and let it cool down. 1. Unscrew the oil dipstick. 13.1 Gasoline engine 2. Wipe the oil dipstick with a clean rag and reinsert, do not screw in. The machine is powered by a gasoline engine. For Pull out the oil dipstick again and read off the instructions on starting and stopping the gasoline oil level, if necessary fill engine oil up to the...
  • Page 18 13.2.2 Fuelling Refuelling 1. Set fuel switch to OFF. 2. Clean the area around the fuel tank cap of dirt and foreign bodies. DANGER! 3. Unscrew the fuel tank cap. 4. Fill fuel tank with gasoline (ROZ95). To allow Health and explosion hazard due to combustion room for the gasoline to expand, do not fill engine.
  • Page 19 When shredding, shredded material, stones and Commissioning the like can splash away. No other persons or animals may be present in the ejection area = danger zone. The machine must not be set up on sloping ground. Special care must be taken to Also be careful not to damage vehicles, glass ensure that the ground does not give way windows and other objects.
  • Page 20 Release the ignition key as soon as the engine starts. This automatically turns back to the ON position. WARNING! Warning against hot surfaces! ATTENTION! The engine exhaust and other engine parts If the engine does not start within 5 seconds, become very hot during operation.
  • Page 21 IMPORTANT NOTICE! Suddenly stopping the engine at full throttle can cause engine damage. 14.4 Stopping the engine in an emergency In dangerous situations, machine movements must be stopped as quickly as possible and the energy supply must be switched off. In case of danger: 1.
  • Page 22: Shredding Operation

    In the case of blockages: Shredding operation Check the machine before each use for: – loose screws and nuts Switch off the engine and remove the spark plug – damaged rubber flap in the infeed chute, connector for safety reasons! replace if necessary –...
  • Page 23 – If the cutting unit is blocked, switch off the engine immediately to avoid overloading the engine. Remove spark plug connector and eliminate fault! Always keep hands away from infeed and ejection openings! In case of unexpected circumstances, never hesitate to operate the safety bar (EMERGENCY Branches up to Ø...
  • Page 24: Maintenance And Repair Work

    Safety goggles with side protection when working on pressurised components or in the vicinity of pressurised systems – Use only original LUMAG spare parts. Other parts may cause unpredictable damage and injury. – Work on the electrical equipment may only be carried out by qualified electricians.
  • Page 25 16.2 Maintenance plan The following sections describe the maintenance work which is required for optimum and trouble-free operation. Before After After After Every Every Every Every Maintenance work each each 1 OH* the first 25 OH* 30-50 needed season 5 OH* Check machine ■...
  • Page 26 16.3 Lubricants IMPORTANT NOTICE! Fuels and lubricants used must comply with the operating material regulations of the operator and the stated specification, consult the supplier if necessary. Fuel Assembly Specification Filling quantity Fuel Engine Gasoline 6.5 litres Lubrication points blade chassis, oscillating axle ROZ95 or higher Engine oil...
  • Page 27 Oil change, upper and lower level ATTENTION! Blade chassis Observe oil level. Do not operate the engine with too much or too little engine oil. See also... Fig. Oil change, upper and lower level. Blunted blades can be turned over. Damaged blades (cracked, chipped, severely bent or otherwise damaged)
  • Page 28 4. Clean foam filter element in warm water and ATTENTION! Place the belt loosely on the drive pulley to mild soap solution. Rinse thoroughly with prevent damage (drive belt tear). clean water and allow to dry thoroughly. 5. Tap out dirt from the paper filter insert on a hard surface, do not brush it off as this will push it into the fibres.
  • Page 29 16.11 Cleaning the machine Check the machine for contamination after use. IMPORTANT NOTICE! Dirt accumulation (twigs, wood debris, dust, A loose spark plug can overheat and damage the adhering leaf green, etc.) inside the machine must engine. Overtightening the spark plug can damage be removed.
  • Page 30 necessary, replace screw connection Transport elements that cannot be tightened with new bolts and nuts. 2. Check the technical condition of the blades by visual and tactile inspection, if necessary DANGER! replace the blades immediately if defects are detected. Danger of burns due to hot surfaces on the 3.
  • Page 31 ATTENTION! Storage If the machine is unhitched from the towing vehicle, it must be parked on a horizontal, level and firm ground. Storage of the machine and temporary shutdown. Store the machine under the following conditions: – Do not store outdoors IMPORTANT NOTICE! –...
  • Page 32 Disposal If the machine is no longer serviceable and is to be scrapped, it must be deactivated and dismantled, i. e. it must be brought into a condition in which it can no longer be used for the purposes for which it was designed.
  • Page 33: Troubleshooting

    Troubleshooting WARNING! Any faults on the machine or engine requiring major intervention must always be repaired by your LUMAG workshop or authorised specialist workshops. The warranty becomes void in the event of improper intervention. Before any troubleshooting – Switch off machine –...
  • Page 34: Warranty

    7.30 a.m. - 12.00 p.m. and 1.00 p.m. - 5.00 p.m. defects. The guarantee for LUMAG products is 24 Friday from 7.30 a.m. - 12.30 p.m. months in the case of exclusively private use, and...
  • Page 35: Ce Declaration Of Conformity

    In accordance with the provisions of the EC Directives Machinery Directive 2006/42/EC EMC Directive 2014/30/EU Outdoor Directive 2000/14/EC the company LUMAG GmbH Rudolf-Diesel-Straße 1a D-84375 Kirchdorf a.Inn Phone: +49 8571 / 92 556-0 Fax: +49 8571 / 92 556-19 explains that the product...
  • Page 36 Components RAMBO-HC15PRO WARNING! All repairs to the machine must be carried out by authorised qualified personnel. Have any necessary electrical work carried out only by an approved specialist.
  • Page 38 Subject to change without notice! Version RAMBOHC15PRO (02.20 D) LUMAG dealer can be found at www.lumag-maschinen.de LUMAG GmbH Rudolf-Diesel-Str. 1a D-84375 Kirchdorf a.Inn Germany Internet: www.lumag-maschinen.de...

Table of Contents