Related Manuals for Elsys EMS2 Door
Summary of Contents for Elsys EMS2 Door
- Page 1 Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se Specifications in this document are subject to change without notice. ©Elektroniksystem i Umeå AB 2020...
- Page 2 For additional information and how to carry out disposal, please contact the certified disposal service providers. The sensors contain a lithium battery, which must be disposed of separately. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 3 Specifications ........................13 Sensor payload format ....................13 Regulations ........................14 Legal Notices ......................14 Federal Communication Commission Interference Statement ......14 Declaration of conformity ..................15 Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 4 Dimensions of the EMS Door sensor (mm) Dimensions of the magnet (mm) The barcode contains DevEUI and sensor type. This label is located at the back of your device. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 5 • Supported channel plans: US902-928, EU863-870, AS923, AU915- 928, KR920-923, RU864, IN865 & HK923 • CE Approved and RoHS compliant *Depending on settings and environmental factors Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 6 Dispose of properly, observing environmental protection rules. 3. Mount the back panel on the surface using the adhesive tape. 4. Attach the cover to the back panel. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 7 Detection range will be affected by the materials of the door and frame, different materials result in different ranges. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 8 NFC to make end-users unable to read or change settings on the sensor. NFC Configuration 1. Download ELSYS “Sensor Settings” application from Google Play and install it on a smartphone or tablet. The device must support NFC. 2. Enable NFC on the device and start the application.
- Page 9 When you have written data to the sensor, let the sensor reboot and restart before trying to write again. You should always validate your settings by reading the NFC data after the sensor has restarted. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 10 After successful connection to a network, the sensor sends a settings packet and enters sampling mode. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 11 Note: The configured sending interval can be overridden by network limitations. Due to this, the spreading factor and sending interval settings might result in longer intervals than intended. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 12 After values has been added to the packet, the EMS schedules a transmission. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
- Page 13 Specifications Sensor payload format The device uses the standard ELSYS payload format. Please see the specified document on our webpage. Power supply: 3.6V DC Battery type: AA 14505 (Li-SOCI EU directives compliance: RoHS 2011/65/EU WEEE 2012/19/EU Radio protocol: LoRaWAN® Radio frequency band:...
- Page 14 All information, including, but not limited to, information regarding the features, functionality, and/or other product specification, are subject to change without notice. ELSYS reserves all rights to revise or update its products, software, or documentation without any obligation to notify any individual or entity. ELSYS and ELSYS logo are trademarks of Elektroniksystem i Umeå...
- Page 15 Declaration of conformity å Hereby, Elektroniksystem i Ume AB declares that EMS Door complies with the essential requirements and other relevant provisions of Directive 2014/30/EU and 2014/53/EU. Elektroniksystem i Umeå AB Industrivägen 12, 90130 Umeå, Sweden E-mail: support@elsys.se ǀ Web: www.elsys.se...
Need help?
Do you have a question about the EMS2 Door and is the answer not in the manual?
Questions and answers